thebarberOriginal postGrand Rapids, MI · Jul 11, 2012#1They had a yaris sedan on a rotisserie at the dealer today so I snapped some photos of its exhaust for those who don't know where the piping shrinks to 1.75"..
Cat, cat, Res from L to R
Picture not included in this copy
Shrinkage after resonator
Picture not included in this copy
Cats...
Picture not included in this copy
Replies 23
new-yaris-ownerMontreal, Qc · Jul 11, 2012#2a yaris needs repair ? must be fake...
thebarberThread starterGrand Rapids, MI · Jul 11, 2012#3Was for display of undercoating...
tooterLos Angeles · Jul 12, 2012#4Hey Barber, 🙂
Thanks for posting the pics. 👍
You convinced me to get a larger catback to axle pipe made after I get the prototype manifold dyno runs done. I took a good look and mine is exactly like those pictures of the demo car (except without the rust 😉 )
Does anyone here know of a competent SoCal exhaust guy who does good custom mandrel bent pipework?
thebarberThread starterGrand Rapids, MI · Jul 12, 2012#5 Originally Posted by
tooter ↑ Hey Barber, 🙂
Thanks for posting the pics. 👍
You convinced me to get a larger catback to axle pipe made after I get the prototype manifold dyno runs done. I took a good look and mine is exactly like those pictures of the demo car (except without the rust 😉 )
Does anyone here know of a competent SoCal exhaust guy who does good custom mandrel bent pipework?
The right-most can I'd actually the resonator....as I've personally done it (before unmodding), just get a res-back exhaust built. The cat and Res are 2" thru and I went with a crush-bent 2.25" to a Megan axleback (also 2.25"). Was awesome.
1.5Tampa · Jul 12, 2012#6Great pics!
Thanks Barber
tooterLos Angeles · Jul 12, 2012#7 Originally Posted by
thebarber ↑ The right-most can I'd actually the resonator....as I've personally done it (before unmodding), just get a res-back exhaust built. The cat and Res are 2" thru and I went with a crush-bent 2.25" to a Megan axleback (also 2.25"). Was awesome.
I'll likely leave all the cans intact and just have a larger pipe fabricated from the exit of the last can to the axleback flange.
1.5Tampa · Jul 12, 2012#8Lets get Malibu in here to fab some sedan midpipes now
07typeSSouthern California · Jul 13, 2012#9 Originally Posted by
tooter ↑
Does anyone here know of a competent SoCal exhaust guy who does good custom mandrel bent pipework?
If you find someone, let me know.. I wanna replace the resonator back piping too and dont know of any reputable places..
malibuguyWestminster, MD · Jul 14, 2012#10 Originally Posted by
1.5 ↑ Lets get Malibu in here to fab some sedan midpipes now
That would not be a problem
1.5Tampa · Jul 14, 2012#11Would you be willing to do some bulk production for some of us
malibuguyWestminster, MD · Jul 14, 2012#12Yes. However the flange on ghe end is going to be an issue...i can only do it flat flange style...vs ball
1.5Tampa · Jul 14, 2012#13do both ends use the ball style? Would you have to leave it flange-less then?
baseballfan416Milwaukee, Wi · Jul 15, 2012#14The lack of a readily available de-catted/free-flowing mid pipe for the sedan is a major setback... It's the one performance piece that the sedan truly lacks from the hatchbacks. Its bottleneck design essentially mitigates performance potential from the a-back exhausts (sorry but I can't justify 2-300bucks for a different exhaust tone, blingy-looking tip, and a butt-dyno gain of 1-2hp that's a placebo effect). I'm sure even the "race" header applications could be enhanced by a free-flowing mid pipe.
So are we just going to sit and talk about it or actually get the ball rolling on this?
tooterLos Angeles · Jul 15, 2012#15I found a local custom exhaust shop with their own mandrel bender, and am going to drop by to get a price on a midpipe for my hatchback. I want to keep the stock cat and all of the stock resonators, and just do the necked down section between the last resonator and the axleback.
cali yarisCanoga Park, CA · Jul 15, 2012#16Which shop? And they will mandrel bend 2"?
tooterLos Angeles · Jul 15, 2012#17 Originally Posted by
cali yaris ↑ Which shop? And they will mandrel bend 2"?
I have no idea, but it's LaBree Motorsports in Canoga Park on Strathern not far from you. I found their business with an online search. It's highly likely that you already know them. I haven't talked to Brent yet, but I will this comng week after the flange is CNCed.
cali yarisCanoga Park, CA · Jul 16, 2012#18^ He doesn't do 2".
Shops that mandrel-bend 2" are very rare. Most will piece together stainless and weld it instead.
tooterLos Angeles · Jul 16, 2012#19I'm open to either possibility. 🙂
Bob's Muffler in Bakersfield has 4 mandrel benders and does up to 3 1/2 inches... but it's not worth the drive. Welded pieces are just fine. No one is going to see them anyways. 😉
malibuguyWestminster, MD · Jul 16, 2012#20in a couple weeks when our back log slows down, ill work on a replacement midpipe for both sedans & hatchies.
tooterLos Angeles · Jul 16, 2012#21Maybe for the sedans, Malibu. I'm going to have one made here locally since I'll be paying the exhaust shop to cut off the old pipe and weld the new one on anyways.
baseballfan416Milwaukee, Wi · Jul 21, 2012#22bumping this one up... The sedan needs a mid-pipe option, better flowing cat or cat less, nothing can be worse than what we already have...
jRossIndianapolis, IN · Dec 9, 2013#23Did this ever happen?
malibuguyWestminster, MD · Dec 11, 2013#24Was trying to make stuff. Sold very few. Dropped the effort.