ChinoCharlesOriginal postOH · Mar 14, 2007#1Ah, the famed port and polish. It is usually a step taken towards the end, but lets assume for a second I had this done on my car right now.
Forget about price... don't sit here and say how the expense isn't worth the gains. A port and polish can run over a thousand dollars alone... this isn't something a lot of people will end up doing to a 1NZ.
My question is assuming a 1NZ was ported, what would happen? I know literally nothing about this... its supposed to net gains, and likely more with a tune like any part. What I am wondering is what do you have to worry about when tuning a car with a P&P? What will happen to timing, air/fuel, engine temps, horsepower... give me (us) an idea.
Replies 75
07typeSSouthern California · Mar 14, 2007#2i think it depends upon what your port and polishing. most common is the intake manifold and that seems to be a problem for us lol. next is your throttle body but then you need a larger butterfly. those are the only 2 i know of....
largeorangefontSo Cal, OC · Mar 14, 2007#3If you did a port and polish to your car as it sits now, the results would be less dramatic than adding a lightened crank pulley.
For all intents and purposes, the intake is already done, as it is smooth plastic. Cleaning the throttle body up, gasket matching the intake and exhaust, cleaning up the ports and doing a bowl blend won't net you too much. Definately less than 5 HP.
RazrChiangmai, Thailand · Mar 14, 2007#4Think about it this way - what gains do you get by freeing up flow with an intake or exhaust? A PP job will have the same sort of effect as it's also just about increasing air flow as well.
Bottom line is it'll kill your low down torque, but increase HP at high RPM.
The question is: is it really worthwhile? I mean the 1NZ-FE bottom-end is not designed to be a high revving powerhouse, in fact it's optimized to be pretty much the opposite. So tweaking/tuning this engine for high RPM performance (with a stock bottom end) will quickly get to the point of little to no net gains IMHO.
Now if you're thinking about forced induction and rebuliding the bottom end, that's a different story! But I would definately be working on these before I'd even consider a PP job.
Many moons ago I was getting 200WHP from a Mazda B6 1.6L Turbo with 15PSI boost, a monster air-air intercooler, a 3" dump pipe through a cat-less system, and a 6" cold-air intake.. Porting and Polishing the heads and putting in custom grind cams (all done by a local rally team that ran the same car) lifted that to 242WHP, so a good 20% gain. BUT you'll notice that it was the last step taken - had this been done before any of the other mods it would have been a WOFTAM.
eTiMaGoBangkok, Thailand · Mar 15, 2007#5ChinoCharlesThread starterOH · Mar 15, 2007#6That thread is legendary. Bet your ass I've seen it before. He made one huge mistake... that Camcon.
Bottom line, if you could have your heads ported for free, would you take it? Yes or no.
I'm not asking your warranty. I'm asking you.
RazrChiangmai, Thailand · Mar 15, 2007#7Free? sure, then I'd Ebay 'em :)
RazrChiangmai, Thailand · Mar 15, 2007#8Let me clarify that a little.. I'd Ebay them and put the money into the "2ZZ-GE engine swap fund".
From everything I've learnt about this engine in the past 2+ years (my last car was a 1NZ-FE as well), it takes mega bucks to make minimal gains.
Our resident sticker guy and all-round good fella eTiMaGo tells me we can get 2ZZ-GE's retrofitted into our Yarii by TRD Thailand for ~100K Baht (USD $2850). Given that the 2ZZ-GE makes 180HP stock, by the time it's in a Yaris with a custom mandrel bent exhaust and intake we should be looking at 200+HP.
There's nothing you can do to a 1NZ-FE for that money that would get remotely close, plus you've got the headroom for forced induction and other mods (if your mother dropped you on your head as a baby, and 200HP in a tiny FWD egg isn't enough) 😁
Anyways, you can see where my thoughts are at 😉
If I could get 4WD and a DSG box to go with a 2ZZ-GE for this thing, I'd order it all tomorrow - along with some blowage, 'cause that'd be a fuckin fun car.
RazrChiangmai, Thailand · Mar 15, 2007#9 Originally Posted by
eTiMaGo ↑
That was a
really good read in fact - thanks!
Kinda confirms everything I've learnt from anecdotal reports with some hard facts for a change. 👍 Too bad you have to sift through all the replies to get to the meaty bits though - a blog would've been awesome.
If you're thinking about tweaking out your Yaris, reading that thread is a must!
eTiMaGoBangkok, Thailand · Mar 15, 2007#10 Originally Posted by
ChinoCharles ↑ That thread is legendary. Bet your ass I've seen it before. He made one huge mistake... that Camcon.
Bottom line, if you could have your heads ported for free, would you take it? Yes or no.
I'm not asking your warranty. I'm asking you.
who could refuse a free head job? 😁
RazrChiangmai, Thailand · Mar 15, 2007#11 Originally Posted by
eTiMaGo ↑ who could refuse a free head job? 😁
Well, there's a few girls I've seen who might give you second thoughts about that 😲 I'm pretty sure it's free too 😉
eTiMaGoBangkok, Thailand · Mar 15, 2007#12 Originally Posted by
Razr ↑ If I could get 4WD and a DSG box to go with a 2ZZ-GE for this thing, I'd order it all tomorrow - along with some blowage, 'cause that'd be a fuckin fun car.
Amen... You could get the transmission and AWD system off an older Celica GT Four, though I have no idea if it'll mate to a 2ZZ... so how about a 3S-GTE Yaris? 😁
eTiMaGoBangkok, Thailand · Mar 15, 2007#13 Originally Posted by
Razr ↑ Well, there's a few girls I've seen who might give you second thoughts about that 😲 I'm pretty sure it's free too 😉
Isn't that what paper bags were invented for?
(it's official, I am going to Hell, or will be reborn as a cockroach)
cleongSingapore · Mar 15, 2007#14 Originally Posted by
eTiMaGo ↑ Amen... You could get the transmission and AWD system off an older Celica GT Four, though I have no idea if it'll mate to a 2ZZ... so how about a 3S-GTE Yaris? 😁
They do have a 4WD 1.3 litre NCP91 Vitz in Japan, though I have no idea how you will get your hands on it. There's all your needed bits right there.
RazrChiangmai, Thailand · Mar 15, 2007#15Could have difficulties lining up a decent 3S-GTE these days, AFAIK they've been out of production for 8+ years now? been a while since Ive seen a GT-4 or MR2, so could be wrong :)
I was thinking more along the lines of the 4WD system from the 1.3L JDM model, and of course
DSG is just a pipe dream - the only Jap brand I know of that's even hinted at one is Honda in the concept/proposed 5dr Civic Type-R :(
RazrChiangmai, Thailand · Mar 15, 2007#16snap! err.. wtf :(
eTiMaGoBangkok, Thailand · Mar 15, 2007#17With the right combination of luck and skill you might be able to import just the front end from a crashed car from japan if it can't be found locally... I have a friend in Krabi who's looking into that, to get a VQ30DE for his Cefiro, I think they quoted something like 30,000B for the engine.
Anyway look into the UK-based Fensport Celica, it's amazing work, they took a latest generation Celica and transplanted the engine and drivetrain from an older GT-4. 650hp or so to all four wheels, nothing to laugh at 😁
MooseCumming, GA · Mar 15, 2007#18OK, I can't read the Scion thread at work because it's blocked, so here's my experience with porting and polishing a head.
And Chino Charles, you are correct in that a P&P is, typically, one of the final steps, and is usually done to compliment your bolt-on power adders- but I'll help you out. 😉
Standing alone, a P&P will gain very little- 15hp is realistic on our little engine- and that's with a very good, thorough job done on a flow bench including valve angles and fuel atomizing dimples.
Now, here is where it gets fun- adding very little to that, we can see much bigger gains- with just I/H/E, cams w/adjustable sprockets (springs and retainers, as well, by default), a fuel pump and injectors (a better fuel pump and AFR wouldn't hurt, either), and a piggyback. With these add-ons, and a dyno-tuner that knows what he is doing, you can make some really great horsepower and torque.
Cliffs?
You can P&P your heart out, but it all comes down to what else you have, and tuning, tuning, TUNING.
ChinoCharlesThread starterOH · Mar 15, 2007#19 Originally Posted by
Moose ↑ OK, I can't read the Scion thread at work because it's blocked, so here's my experience with porting and polishing a head.
And Chino Charles, you are correct in that a P&P is, typically, one of the final steps, and is usually done to compliment your bolt-on power adders- but I'll help you out. 😉
Standing alone, a P&P will gain very little- 15hp is realistic on our little engine- and that's with a very good, thorough job done on a flow bench including valve angles and fuel atomizing dimples.
Now, here is where it gets fun- adding very little to that, we can see much bigger gains- with just I/H/E, cams w/adjustable sprockets (springs and retainers, as well, by default), a fuel pump and injectors (a better fuel pump and AFR wouldn't hurt, either), and a piggyback. With these add-ons, and a dyno-tuner that knows what he is doing, you can make some really great horsepower and torque.
Cliffs?
You can P&P your heart out, but it all comes down to what else you have, and tuning, tuning, TUNING.
Heyyyy, someone that didn't try and convince me to swap my engine! 🙄 Thanks Moose!
15?! That is pretty damn good, even if that is with a tune. It sounds like the optimistic side of the argument compared to Ashley's "its another cold air intake," so I'm anxious to see who is right. Honestly, everything I've been told so far backs you up Ashley... gains will be tiny, but once I have all this stuff done and I slap the piggyback on there and hand my car to Kevin, I'm expecting something crazy... for a Yaris. We shall see.
You may see a P&P 1NZ head next week.
DragonaccAtl, GA · Mar 15, 2007#20 Originally Posted by
ChinoCharles ↑ Heyyyy, someone that didn't try and convince me to swap my engine! 🙄 Thanks Moose!
15?! That is pretty damn good, even if that is with a tune. It sounds like the optimistic side of the argument compared to Ashley's "its another cold air intake," so I'm anxious to see who is right. Honestly, everything I've been told so far backs you up Ashley... gains will be tiny, but once I have all this stuff done and I slap the piggyback on there and hand my car to Kevin, I'm expecting something crazy... for a Yaris. We shall see.
You may see a P&P 1NZ head next week.
If it's free does it matter if the gains are small? 😆
If you had to pay for it on the other hand, I wouldn't recommend the expense.
ChinoCharlesThread starterOH · Mar 15, 2007#21My concern is this.
I get my head ported next week and go to the dyno. We dyno the new head and everything is whacked out. I lost 5 HP throughout and the ECU is now running a 9.5 AFR. In other words, my main concern is that the stock ECU isn't even going to know where to start.
If this is the case, so be it... the P&P just has to wait until I have a piggyback.
If not, I'll do the P&P first.
What ends up happening is I am literally loading my car like a slingshot right now. With every mod I do, I'm getting power earlier, although I'm not necessarily getting more of it. The engine is running richer and richer. The power also comes on sooner.
Then I get a piggyback and it is the proverbial launch of the slingshot. All of the sudden AFR is where it ought to be, the HP curve doesn't flatten out at 5000 RPM anymore and my car literally nets 25 HP in one day... at least I hope.
If it does, it proves my theory that there is power in this engine and that kid on Scionlife spent all the right money on all the wrong shit. If not, I'll probably be the last person to mod a 1NZ. 😆
DragonaccAtl, GA · Mar 15, 2007#22 Originally Posted by
ChinoCharles ↑ My concern is this.
I get my head ported next week and go to the dyno. We dyno the new head and everything is whacked out. I lost 5 HP throughout and the ECU is now running a 9.5 AFR. In other words, my main concern is that the stock ECU isn't even going to know where to start.
If this is the case, so be it... the P&P just has to wait until I have a piggyback.
If not, I'll do the P&P first.
What ends up happening is I am literally loading my car like a slingshot right now. With every mod I do, I'm getting power earlier, although I'm not necessarily getting more of it. The engine is running richer and richer. The power also comes on sooner.
Then I get a piggyback and it is the proverbial launch of the slingshot. All of the sudden AFR is where it ought to be, the HP curve doesn't flatten out at 5000 RPM anymore and my car literally nets 25 HP in one day... at least I hope.
If it does, it proves my theory that there is power in this engine and that kid on Scionlife spent all the right money on all the wrong shit. If not, I'll probably be the last person to mod a 1NZ. 😆
Normally I'd expect an engine to lean out as more airflow mods are added, if yours isn't it makes me think the ECU is "learning" and trying to keep inside some kind of stock parameters. If that's the case the P&P will probably be more of the same.
MooseCumming, GA · Mar 15, 2007#23Charles, wait until you have the piggyback and some better injectors, or you will run lean. On top of that, with these ECUs the knock sensor may start bitching as well because the engine will try to adjust timing to match the new amounts of air flowing through the head- this is one of the reasons I built a non-VTEC B18 in my Civic.
The goal is a nice, FLAT 12:1 air fuel ratio- and don't get mad when your MPG goes sub-30.
ChinoCharlesThread starterOH · Mar 15, 2007#24Sub-30 I can live with. I don't drive much. (Yeah right 😉)
Wait... or I will run LEAN? I'm running rich now... is there a chance a P&P will balance it out a bit, or at least enough so that I can go with the P&P now and roll around on it for a month before its piggyback time?
MooseCumming, GA · Mar 15, 2007#25 Originally Posted by
ChinoCharles ↑ Sub-30 I can live with. I don't drive much.
Wait... or I will run LEAN? I'm running rich now... is there a chance a P&P will balance it out a bit, or at least enough so that I can go with the P&P now and roll around on it for a month before its piggyback time?
How rich are you running? 10:1? Worse?
Never mind, I just saw 9.5:1. Holy shit! Is that all across the powerband or just in one place, like a peak?
ChinoCharlesThread starterOH · Mar 15, 2007#2610.75:1 at worst, 11.5:1 66% of the powerband.
9.5 was a hypothetical.
2000-5000 RPM: about 11.5:1 AFR
5000-5800 RPM: descends to 10.75:1
5800 on: stays around 10.75:1, horsepower flattens out, torque decreases 10%.
largeorangefontSo Cal, OC · Mar 15, 2007#27 Originally Posted by
ChinoCharles ↑ 10.75:1 at worst, 11.5:1 66% of the powerband.
9.5 was a hypothetical.
2000-5000 RPM: about 11.5:1 AFR
5000-5800 RPM: descends to 10.75:1
5800 on: stays around 10.75:1, horsepower flattens out, torque decreases 10%.
Taking AFR through through the tailpipe on a dyno through OEM cats will give you invlalid results. You need a wideband with a bung installed pre cat.
Your mileage will improve after a tune. That is if you aren't flooring it more than you were to begin with.
If you are gonna get a PnP done free by a reputable shop in your area, yes It may be worth it. If some toolbox shop does it, it will most likely do more harm than good. I wouldn't pay to have it done to this motor. The funds are better spent elsewhere, either an engine swap, or a turbo\supercharger.
I used to work at a shop porting cylinder heads for many championship race teams in various forms of racing, so I know all the processes and methodologies pretty well. Moose is correct, although I doubt you would see 15 Hp on this particular engine without cams or other component upgrades.
jdubau55Blacksburg, VA · Mar 15, 2007#28The 2ZZ is out of the question IMHO. There will be much easier swaps soon. I really think your best bet is to just find a Yaris thats totaled and rape the engine out of it. Make it your coffee table and then slowly build it in your living room. Build it bulletproof and slap a turbo on it. A 1.5 liter motor with a proper turbo build should have no problem making 250 WHP and be perfectly stable. Its all about the build though.
DragonaccAtl, GA · Mar 15, 2007#29 Originally Posted by
jdubau55 ↑ The 2ZZ is out of the question IMHO. There will be much easier swaps soon. I really think your best bet is to just find a Yaris thats totaled and rape the engine out of it. Make it your coffee table and then slowly build it in your living room. Build it bulletproof and slap a turbo on it. A 1.5 liter motor with a proper turbo build should have no problem making 250 WHP and be perfectly stable. Its all about the build though.
You are going to spend a lot of money to get that 250hp... Why build an engine if you are only going to get 250hp? If someone is hell bent on making a lot of power in a Yaris the 1nz is not the way to do it.
jdubau55Blacksburg, VA · Mar 15, 2007#30As far as the PnP goes. I say do it. All it can do is help if its done right.
I am talking reliable, easy, HP. Swapping a 1NZ for a 1NZ would be straight forward. Sure you could make more HP, but the more you make the more risks you are taking.
MooseCumming, GA · Mar 15, 2007#31 Originally Posted by
largeorangefont ↑ Taking AFR through through the tailpipe on a dyno through OEM cats will give you invlalid results. You need a wideband with a bung installed pre cat.
Yeah, I was wondering what was up with your AFR.......that's not even close to what it should be! I mean, 11.5:1 is acceptable, but when you start dipping into the 10.X:1 area, that's not good. You could start having problems long term- excessive carbon buildup, detonation, premature O2 sensor failure, etc.....
acrbillchicago · Mar 15, 2007#32The thing about porting and polishing is that every head design requires different work. A lot of the time there is a long trial and error process before every bit of power is extracted.
There are basic things that every head port & polish should include.
Port match intake ports to the manifold.
have a slightly rough texture to the intake ports to help the fuel mix with the air.
open up the exhaust ports and get them as smooth as possible.
unshroud the valves if needed and polish the combustion chambers.
A bad port job can cost you power all over the place too. Keep in mind that it takes 8-12 hours to port and polish a head (for someone who does it often) so if some guy is offering it for free I would be suspect.
Porting heads traditionally offers huge gains. The problem with the Yaris is that it has a relatively low rev limit so much of the potential gains will be beyond the stock rev limiter.
If the guy is just going to clean up the ports I wouldn't bother. Once you open the motor up you are opening the proverbial can of worms.
ChinoCharlesThread starterOH · Mar 15, 2007#33Wow, a lot to respond to.
About the AFR being wacky, it was taken through the tailpipe.
The next question would be when I dyno the car with the new test pipe this Sunday, should I get an accurate AFR reading due to the fact that the cats are being removed?
And about the shop... this is a local area shop involved in racing engines and they want to break into the subcompact market. They offered me a P&P to display a sticker. They said it would take four days. I told them I am very interested, but I would like to know what they suggest on a low displacement engine like the 1NZ. If they say "nothing different from a Ford V8" I'll be weary.
acrbillchicago · Mar 15, 2007#34Man it kills me to do this to you. It seems like every thread you create I pop on and attempt you ruin your fun.
I would run away from that deal. Nothing in life is free.
Here is an example of how shops with good intentions end up screwing people in the long run. Unfortunately its far too common.
A few years back I took a side job working for a very well known person in the car community.
My job was to fabricate turbo kits from scratch. He had very good intentions up until the point he stopped paying me and he took a lot of peoples money.
One guy actually let the shop use his car in order to build the turbo kit. In return he was supposed to get a free kit.
He ended up picking up the car after over a year went by and the car was worse off than when he dropped it off.
Now if a shop says they are going to do free work, they are not going to give the car a whole ton of attention if paying customers come in.
You also have to think about all the potential problems that might come up.
Removing the head means that you will need a new headgasket, headbolts, intake and exhaust manifold gaskets at a minimum. What if they skip a few teeth on the timing belt when they install it and the valves contact the pistons? The fact that you are not paying them means you will have zero recourse if something goes wrong.
If they have no experience with a Yaris head they won't know where the water jackets are in the head. If the guy porting the head takes away too much material in the wrong spot the head will be scrap.
Are you willing to have your entire valve train removed? Toyota engineers who set the torque specs for every nut and bolt know what they are doing. The shop that is not getting paid might not take the same care.
They say it will take 4 days, I would budget 2 weeks at a minimum.
They say they will do the work for free. I would make damn sure that you buy an OEM headgasket and headbolts and bring them in with the car. Those are non reusable parts that they might try and reuse.
I would be very very careful.
largeorangefontSo Cal, OC · Mar 15, 2007#35 Originally Posted by
ChinoCharles ↑ Wow, a lot to respond to.
About the AFR being wacky, it was taken through the tailpipe.
The next question would be when I dyno the car with the new test pipe this Sunday, should I get an accurate AFR reading due to the fact that the cats are being removed?
And about the shop... this is a local area shop involved in racing engines and they want to break into the subcompact market. They offered me a P&P to display a sticker. They said it would take four days. I told them I am very interested, but I would like to know what they suggest on a low displacement engine like the 1NZ. If they say "nothing different from a Ford V8" I'll be weary.
Theoretically, yea the AFR should be accurate. however, I rarely have seen a dyno tailpipe sniffer that is accurate. They are dropped, stepped on, dirty, and run in the worst possible conditions (super rich, super lean) etc. Just take it for what its worth.
It sounds like they aren't going to do anything radical with the head. Probably just some cleanup and smoothing if they think it is only going to take 4 days. Keep in mind car work is like construction work. 4 days equals 4 weeks. And that is if all the new gaskets are available from your local dealer. They may even use aftermarket gaskets to replace the OEM stuff, so be aware of that.
Ashley
ChinoCharlesThread starterOH · Mar 15, 2007#36Advice noted. Thanks.
Decision shortly.
Black YarisToledo, OH · Mar 16, 2007#37So what are the plans for TI for this week end..... I can't wait to hear/see that exaust... shit if I have time, and they have time, see if they can change my exaust up a bit... hit me up L8er
GalavoxxSan Francisco · Mar 16, 2007#38Does anyone know if bigger valves have ever been fitted to this head? Or if it might be possible? I have no idea what the inside of the head looks like on the 1NZ but larger valves can net more gains when used in conjunction with the P&P. Just a thought. 🤷
DragonaccAtl, GA · Mar 16, 2007#39 Originally Posted by
Galavoxx ↑ Does anyone know if bigger valves have ever been fitted to this head? Or if it might be possible? I have no idea what the inside of the head looks like on the 1NZ but larger valves can net more gains when used in conjunction with the P&P. Just a thought. 🤷
Larger valves won't help unless you increase the redline or go FI. Bigger valves kill air velocity which hurts bottom end power.
GalavoxxSan Francisco · Mar 16, 2007#40 Originally Posted by
Dragonacc ↑ Larger valves won't help unless you increase the redline or go FI. Bigger valves kill air velocity which hurts bottom end power.
I don't entirely agree with that. OF course a higher redline is going to showcase the potential of larger valves. However, with a flow bench designed head and larger valves, the hp should be avilable everywhere, not just up high. I'm not saying that the 1NZ has the potential to make more power with just valves and a head job but the potential of a stock internal 1NZ engine with just head work has yet to be realized. Many head jobs (good ones) will bear the ideal combination of performance, reliability, and drivability. This is done by balancing all of the head elements such as matching valve size and shape to seat geometry to port configuration. Bottom line: a head alone on many cars can conservatively net horsepower gains of 5 – 10% (and occasionally even more) and this is stage 1 on stock internals. But you probably already know this. Of course we will also have to get into the electronics...
DragonaccAtl, GA · Mar 16, 2007#41 Originally Posted by
Galavoxx ↑ I don't entirely agree with that. OF course a higher redline is going to showcase the potential of larger valves. However, with a flow bench designed head and larger valves, the hp should be avilable everywhere, not just up high. I'm not saying that the 1NZ has the potential to make more power with just valves and a head job but the potential of a stock internal 1NZ engine with just head work has yet to be realized. Many head jobs (good ones) will bear the ideal combination of performance, reliability, and drivability. This is done by balancing all of the head elements such as matching valve size and shape to seat geometry to port configuration. Bottom line: a head alone on many cars can conservatively net horsepower gains of 5 – 10% (and occasionally even more) and this is stage 1 on stock internals. But you probably already know this. Of course we will also have to get into the electronics...
It's true headwork and larger valves
can gain power everywhere. But unless the stock valves are too small for the airflow requirements of the engine adding larger valves will hurt bottom end performance.
Now, I suppose the only way to really know if the valves are too small is to spend time with the heads on a flowbench and the car on a dyno.
GalavoxxSan Francisco · Mar 16, 2007#42 Originally Posted by
Dragonacc ↑ Now, I suppose the only way to really know if the valves are too small is to spend time with the heads on a flowbench and the car on a dyno.
If I only had the cash. A good flowed head job alone with valves, if needed, could cost anywhere from $2 to $3 grand. At Least!!
MooseCumming, GA · Mar 16, 2007#43 Originally Posted by
Galavoxx ↑ If I only had the cash. A good flowed head job alone with valves, if needed, could cost anywhere from $2 to $3 grand. At Least!!
When I had my B18 head worked (5 angle valve job, intake gasket matching, polishing and "ported as wide open as possible"), I paid $3750. The work took a week and a half.
I should add, though, that included balancing my rods and pistons, jet-hot coating the piston tops, and installing valvetrain. So, $3000 is a good figure for a good head job.
Yup, shit's expensive.
joey1320Lakewood, Ohio · Mar 16, 2007#44a good, reputable shop should know how to clean a head for better flow-no matter what name is on the hood of the car. now if it's a small shop with not much knowledege, trying to get into a new market then i might be worry about it.
they should definitely bench flow it to see the before and after and you should be there to see the difference. you don't wanna get the car back together to figure out they messed up big. good luck!
mikeukrainetzCanada · Mar 16, 2007#45listening to all this amazes me, im really not used to the import engine build and the lengths people will go to for 5 - 10hp. what I am used to is gaining 60hp with an aftermarket set of heads for a small block. It seems like theres maybe one or two here who actually know whats involved in a P&P job. Its not one of those DIY on the weekend kind of things. Most people, even shops who arent familiar with certain types or model variations of heads can ruin a 1k set of heads by removing too much material. people also think they can just hog out material to the max and expect huge gains in flow. Ive seen heads so thin they literally cant hold water. Overheating winds up being a problem and cracking around valve stems. The only way I can see this being a justifiable expense is if the bottom end is built and your boosting. I wouldnt worry about valve size either.
Are you guys actually serious of doing this to this engine? If so go with the advice of a good shop with a flow bench.
Just because the heads flow better wont net you much without opening everything else up.
ChinoCharlesThread starterOH · Mar 16, 2007#46Listen. You guys don't know Ohio.
Summit Racing... if I'm not mistaken, one of the largest domestic parts distributors in the country... and one of the largest distributors overall. They have everything. Their warehouse is HUGE. you can walk in on any day and leave with anything from crate engines to the little condom that goes on your LED. There are also a few tracks around here... a few.
So, I live in what is basically the best 50 square miles to build a domestic muscle car. There are 18 year old kids where I live that can tell you how to put 550 to the rear in a Nova.
I drive a Yaris.
Somehow I have an intake in my car that people are drooling for. And these domestic guys can manufacture MAF plates. And I can buy the rest at... you guessed it.
I'm on here so much I could almost tell you anything about this specific car. If not, I'm on here asking you guys within 12 hours. This is my finest resource, and the main reason isn't necessarily because of the advice. Its the vendors. If you want people who won't bullshit you on cars, talk to someone who deals with them every single day.
Yadda yadda yadda... now I'm sitting here with a car that looks 5 steps short of sex, I have a dyno and tuner to play with and I have a P&P sitting in my fucking lap.
In the heart of domestic country, there is a Yaris getting attention. This is easily the funniest shit I've ever done in my life. There is a LOT of pulling up and just having a good laugh.
Now, I'm at a point where I'm staring something in the face and I don't know if I can take the next step. I could possibly get this done, continue trying to tune this car and get lucky. If it takes hold, I now have a successful P&P sponsorship in my pocket... and I have an intake on the market. My goal from day one has been to just try and bring attention to it. Now I'm possibly holding the Yaris with the most interesting story in the country... and in debt 10 grand in a warranty-void car. Lets hope the poor bastard sells some intakes.
Flipside... I blow my car up and I'm fucked for life. You guys do such a wonderful job of reminding me of this, I couldn't thank you enough. 😆 The question is do I trust these domestic shops to play with a 1NZ. Keep in mind I have Baskin as my main guide, and I have literally never seen a problem he couldn't fix. Granted, there is no way to fix an overported head.
Now tell me what you'd do.
Black YarisToledo, OH · Mar 16, 2007#47Chino... is our head the same as a XA, XB or Echo? If so.... I am sure I can get you those all day long if there is a fuck up
ChinoCharlesThread starterOH · Mar 16, 2007#48I'd assume so... same engine, similar HP specs. Guys?
DragonaccAtl, GA · Mar 16, 2007#49 Originally Posted by
mikeukrainetz ↑ lIts not one of those DIY on the weekend kind of things. Most people, even shops who arent familiar with certain types or model variations of heads can ruin a 1k set of heads by removing too much material.
Depends on the heads. I can port a set of E7 heads for a SBF and they'll make quite a bit more power than stock. 😉
Import cars can cost a bunch to get power out of, but when done properly they make serious power. Just look at some of the 800 hp B series turbo engines out there.
DragonaccAtl, GA · Mar 16, 2007#50Chino, your part of Ohio sounds like where I live. We have a Summit here too, and several really really good engine/machine shops. Atlanta Motor Speedway, Road Atlanta up north etc. etc.
I wish you the best of luck with your endeavors in 1NZ power production.