Yarisworld Archive

AEM F/I C

19 posts · 6,578 views

packetraceOriginal postQuebec · May 28, 2012#1
Some one have done a DIY or something on the install of the AEM FIC ? 😁

Thank you!

Replies 18

packetraceThread starterQuebec · May 28, 2012#3
Nice scott! I will check it ou later today :)

Does the aem fic come with a long harness to go from the cabin to the engine bay to get plugged to the pnp ?
packetraceThread starterQuebec · May 28, 2012#4
DOes the AEM FIC replace the stock ECM and so on I could take the stock ecm out of there ?
CTScottUSA, CT · May 28, 2012#5
The F/IC has a two connector harness that is about 4' long, which they intend for you to cut into the factory harness. My DIY shows how to make the equivalent to a boomslang PNP harness for less than 1/2 the cost. A PNP one means that you unplug the existing OEM harness connector and plug the PNP in, in between the connector and the ECM. This avoids cuts and splices to the factory harness.

It is a piggy back ECU, so you connect its harness on top of the existing ECM harness and leave the ECM in place. I mounted mine behind the passenger glove box to minimize the wire length.
packetraceThread starterQuebec · May 28, 2012#6
SO you can't use only the AEM as engine computer....?

I must used the ECM plus the AEM to controle only SOME of the settings ? If I ever put a turbo in...

IS that what I should understand ?
CTScottUSA, CT · May 28, 2012#7
Originally Posted by packetrace ↑
SO you can't use only the AEM as engine computer....?

I must used the ECM plus the AEM to controle only SOME of the settings ? If I ever put a turbo in...

IS that what I should understand ?
The F/IC is a Fuel and Ignition Controller. The stock ECM does all of its normal functions and the F/IC sits on top of it to provide the ability to add fuel and pull timing where necessary.

It is of little use with a NA car, but a device of its nature is required when adding FI to compensate for the additional air with proportionately more fuel.
fnkngrvIn The Hotbox · May 28, 2012#8
The AEM F/IC, Greddy eManage, Greddy Blue, CAMCON, etc are all called Piggyback ECUs. They are not standalone replacements.
packetraceThread starterQuebec · May 28, 2012#9
Originally Posted by CTScott ↑
The F/IC is a Fuel and Ignition Controller. The stock ECM does all of its normal functions and the F/IC sits on top of it to provide the ability to add fuel and pull timing where necessary.

It is of little use with a NA car, but a device of its nature is required when adding FI to compensate for the additional air with proportionately more fuel.
Yeah it is not for a NA car...I am just taking information if I put a turbo somewhen....and just learn for learning since I am no good at mecanic....
packetraceThread starterQuebec · May 28, 2012#10
Originally Posted by fnkngrv ↑
The AEM F/IC, Greddy eManage, Greddy Blue, etc are all called Piggyback ECUs. They are not standalone replacements.
Thank you!

Was is the exact definition of piggyback ?
cali yarisCanoga Park, CA · May 28, 2012#11
^ Already explained in this thread. A piggyback computer takes over some (but not all) of the functions the stock ECU performs to run the motor. Usually this includes fuel, timing and sometimes rev limit, etc. It is wired into the ECU, which must stay in the car to run all the other functions.
cali yarisCanoga Park, CA · May 28, 2012#12
If you leave the title of the thread as "AME" it will be hard to find for anyone searching for the information to find this thread -- best to edit that, IMO.
packetraceThread starterQuebec · May 28, 2012#13
Originally Posted by cali yaris ↑
If you leave the title of the thread as "AME" it will be hard to find for anyone searching for the information to find this thread -- best to edit that, IMO.
Changed :) sorry 😉
packetraceThread starterQuebec · May 28, 2012#14
Originally Posted by cali yaris ↑
^ Already explained in this thread. A piggyback computer takes over some (but not all) of the functions the stock ECU performs to run the motor. Usually this includes fuel, timing and sometimes rev limit, etc. It is wired into the ECU, which must stay in the car to run all the other functions.
I just was not sure thank you! 😳
cali yarisCanoga Park, CA · May 28, 2012#15
no problem! 🙂
g.q.viosOrange County · Sep 14, 2012#16
So bringing and old thread back to life!!! I was over at aem web site and found
INFINITY STAND-ALONE PROGRAMMABLE ENGINE MANAGEMENT SYSTEM from aem... I mean the haltech system are like 1500 each plus tunning and wiring the sucker ouch!!! @ garm A lil birdie told me you where running aem series 2 but lost your power steering... And the cheap option is the f/ic but i hear alot of people having problems with it!!! I live in so cal and have at least 20+ tunners in the area certified by aem so i dont think tunning the F/ic would be a problem but it has its limits... So i was wondering what would be a better solutin for etheir a good piggy back or a good stand alone that will work and keep all parts of the car working... Like in garms car i think you lost the A.C power steering and anything else!!! I would like to keep these features Any good advive thanks ...👍
packetraceThread starterQuebec · Sep 14, 2012#17
Actually i am still questionning myself about goong standalone or piggyback...for budget reason and for simplicity reason...

Buy i dont want a fic...if i go with a piggyback i will choose the gredy ultimate or the haltech sprint 500...

I will try to keep the power steering...i dont have ac so no problem
With it....idle is controlled by the standalone...you dont losse many stuff with thr standalone :p

If standalone..haltech 1000, aem ems plug n play or megasquirt 3
g.q.viosOrange County · Sep 14, 2012#18
I was just wondering Cause you had bought the F/Ic from Garm then Sold It Why??? And If You Do go With greedy E manage or haltech is it going to be plug and play or D.I.Y
packetraceThread starterQuebec · Sep 15, 2012#19
I bought it used with my engine, piping, intercooler etc...

Thats why I sold it :P dont want that shitty fic! Because i am goong 15psi more or less..and i want it reliable and viable...