tooterOriginal postLos Angeles · Apr 30, 2012#1The header just arrived today, and it looks like a piece of jewelery... 🙂
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
This is a view looking into the exit pipe. You can see the split Y nature of the header.
Picture not included in this copy
I'll post more pics during the installation effort. It also came with a new donut gasket, but not an engine gasket. I don't think that will be an issue since the engine has less than 200 miles on it.
Replies 79
1.5Tampa · Apr 30, 2012#2ooooooooo so shiny
GolddeenohColumbia, SC · Apr 30, 2012#3^ what he said but more excited and louder.
WeeYariGeorgetown, Ontario, Canada · Apr 30, 2012#4Installed yet??? No!! Why not???
Come on, come on, hurry it up!!! 😉
goliath1812Ocala Florida · Apr 30, 2012#5:) let's see it installed and tested!! :)
marcustoronto, canada · Apr 30, 2012#6subscribed
tooterThread starterLos Angeles · Apr 30, 2012#7Well, it only took 2 hours to get the old header off! 😆
The car needs to be jacked up so that you can get underneath to loosen the 2 spring bolts holding the downpipe to the header. All the header bolts were easy compared to the one lower bolt that holds the bottom flange of the header to a support bracket. That one was an absolute b*****rd to get off.
Here's comparative pics of the headers. At 5 pounds 12 ounces, the Weapon R header is 6 ounces heavier than the stock header because it has a really thick flange.
Picture not included in this copy
The stock tubes are 28mm diameter, while the Weapon R tubes are 36mm in diameter. This is an increase of 30%.
Picture not included in this copy
I'll begin to install the new header today just to see if it fits, but won't be able to complete it because I need to get some new bolts. The bottom exit tubing needs to be ground down as it's about 3/8 inch too long. This isn't a problem that a grinder can't fix. 🙂
CrankyOldManWest Michigan · Apr 30, 2012#8I'm curious about how the change in diameter affects flow velocity and scavenging efficiency. There has been lots of discussions centered around those mechanics for intakes, exhaust headers, mid-pipes, axle-backs and even short downpipes.
Also, are you going to heat-wrap it? I've seen a few people do that to reduce engine bay temps--but I think they have a CAI as well.
tooterThread starterLos Angeles · Apr 30, 2012#9 Originally Posted by
CrankyOldMan ↑ I'm curious about how the change in diameter affects flow velocity and scavenging efficiency. There has been lots of discussions centered around those mechanics for intakes, exhaust headers, mid-pipes, axle-backs and even short downpipes.
Also, are you going to heat-wrap it? I've seen a few people do that to reduce engine bay temps--but I think they have a CAI as well.
I have no idea. I'm just going to install it and drive it and see how it works. Tri Y headers are a very old tried and true exhaust design based on sound physical principles, so I trust in the manufacturer's R & D that it will work just fine.👍
Discovered that the stock donut gasket won't fit the new header because the stock exit tube is 45mm in diameter while the Weapon R is 47mm for an increase of 4.5%. Thankfully it came with its own oversized donut. 🙂
Ground off the excess tubing to fit the donut...
Picture not included in this copy Next comes the installation...
cali yarisCanoga Park, CA · Apr 30, 2012#10Can you post a few more pictures of the new stock header? Looks different than previous years.
auxmikeLI, New Yawk · Apr 30, 2012#11Any trouble getting the airflow sensor out of the OEM manifold?
tooterThread starterLos Angeles · Apr 30, 2012#12Ta da... 🙂
Picture not included in this copy
Picture not included in this copy
As Ace Ventura would say... "Like a glove..."
Picture not included in this copy
Idles nice and quiet and smooth and did not trigger the Check Engine Light. Gonna take it for a test ride, then I'll disconnect the battery to let everything reset to allow for the new parameters.
tooterThread starterLos Angeles · Apr 30, 2012#13 Originally Posted by
auxmike ↑ Any trouble getting the airflow sensor out of the OEM manifold?
No, it came off very easily. 🙂
I took the old manifold out first... and then removed the sensor by slipping a 19mm box end wrench over the sensor plug to get to the nut. I had plenty of leverage with it out on the ground and there was no way for the wrench to slip off.
Took the car for a test run to town to gas it up and calculate the mileage. The benchmark pre header mileage is 36.5 for the first 207 miles. Next fillup I'll have a pretty good idea of how much the mileage improves with the header.
I do know this... the header works
great! 👍
It has a bottom end sweet spot from 2,000 to 3,000 rpm which is right where I drive the most. There's a really steep hill going up to the house, and the car used to bog down in 2nd gear so you had to press more on the gas to get it to go. Now, that's completely
gone! You just press like normal and it goes right up the hill with no bogging down.
I really didn't expect a whole lot of difference seeing as the rest of the exhaust is totally stock, pumpkin muffler and all, but this marked improvement in low end torque is
far beyond my expectations. 👍
The installation took me a total of 6 hours including an hour of grinding the excess tubing off the header. Everything was done by the "Braille method" because there was no way to directly view what I was doing. I was able to use
all of the original bolts including the OEM spring bolts whiwh attach the header to the downpipe. Later I'm going to get some longer engine bolts because the thickness of the flange, but there was still plenty ot threads on the stock ones, and the torque on them was light because they came off without any hesitation even from the awkward working conditions.
tooterThread starterLos Angeles · Apr 30, 2012#14 Originally Posted by
cali yaris ↑ Can you post a few more pictures of the new stock header? Looks different than previous years.
Yes, it's very different.
I'll post detailed pics tommorrow when there's good daylight. It's a really strange combination of tubing with a falafal like shell molded over them with a welded seam all around the edges. It must work pretty well overall, because the factory has the luxury to test its designs to see what works best over the widest range of driving conditions.
Bottom line: I'm
totally pleased with the low end torque of this Tri Y header. It outperformed my expectations. 🙂
vtencolumbus · Apr 30, 2012#15its the same design witht the one I have since a couple years ago .
it's a good buy
1 attachment not included in this copy
1.5Tampa · May 1, 2012#16Looks great what does the butt dyno say?
tooterThread starterLos Angeles · May 1, 2012#17 Originally Posted by
cali yaris ↑ Can you post a few more pictures of the new stock header? Looks different than previous years.
Hey Cali, 🙂
Here's some pics of the 2012 OEM header. Note the horizontal bulges connecting the outer two tubes...
Picture not included in this copy ...and on the other side horizontal bulges connecting the inner tubes. Toyota configured their OEM header a semi-tri y design although none of the tubes are discretely separated from each other like the WR header.
Picture not included in this copy The inside is all one open smooth undulating chamber.
Picture not included in this copy Picture not included in this copy What had appeared to be tubes welded inside the engine flange are actually the two halves of the formed metal header shell. Each side makes up 180 degrees of the tubes.
Picture not included in this copy It reminds me of those hot pressed sandwich makers that seal the sandwich all around the edges, except in this case the sandwich is welded. 😆 Side view shows the full length weld.
Picture not included in this copy malibuguyWestminster, MD · May 1, 2012#18that reminda me of a 5th gen terseo manifold.
prior to installing my weapon r header i ported the lower weld joints to smooth them out. i did not have the longer bits to go further in.
mine did not come with a new donut gasket...i just ordered a replacement from advanced auto...fit perfectly on.
mr_milesPortland, OR · May 1, 2012#19Do want! looks good.
tooterThread starterLos Angeles · May 1, 2012#20I think that the seller threw the gasket in extra because it wasn't inside the sealed header bag.
I did a lot of searching, and BeanGarage.com had the very best price for the Weapon R, $20 cheaper than the next closest seller...
...it was only $209 with free shipping and no sales tax. 🙂
CrankyOldManWest Michigan · May 2, 2012#21 Originally Posted by
malibuguy ↑ prior to installing my weapon r header i ported the lower weld joints to smooth them out. i did not have the longer bits to go further in.
You mean these rough spots? Seems like it wouldn't be hard for WR to put a wire wheel down in there and clean it up.
Originally Posted by
tooter ↑ This is a view looking into the exit pipe. You can see the split Y nature of the header.
Picture not included in this copy
tooterThread starterLos Angeles · May 2, 2012#22Might need some sort of specialized grinding tool as those joints in the picture are about 6 inches or so up inside. Anyways, mine won't be coming coming off as it works great just as it is, and the car isn't being entered in competition. 😉
malibuguyWestminster, MD · May 2, 2012#23no wire wheel is going to fix that. i use a head porting kit..or in my case one left over bit from a kit then about 2min of my time.
i paid more for mine...but i got from a licensed dealer jic there is any issues
tooterThread starterLos Angeles · May 3, 2012#24BeanGarage.com is an authorized Weapon R merchant and carry a full line of their products. They specialize in sub compact parts and accessories. They had hands down the very best price and good service with prompt free shipping. 👍
pennyracergrants pass · May 4, 2012#25do you use any thread compound on the 02 sensor threads ?
tooterThread starterLos Angeles · May 5, 2012#26 Originally Posted by
pennyracer ↑ do you use any thread compound on the 02 sensor threads ?
Yes. I put a little dab of antisieze on everything that gets hot... and learned to do that the hard way. 😉
tooterThread starterLos Angeles · May 5, 2012#27 Originally Posted by TPA5 ↑
That looks hot, definitely a mod I want to do for my Yaris! Very clean install.
Thanks. 🙂 It was suprizingly straightforward. No one had listed 2012's as being applicable. I just took a chance that the relationship between the engine and downpipe would remain the same over the years, even though the design of the OEM header had changed. I wrote to BeanGarage and let them know the header fit so they could update their listings.
Are you planning to do a cat-back as well?
No. Just going to flux weld a cheap $15 twin tip onto the pumpkin muffler pipe. My wife likes it quiet. 😉
DeathBeardLos Angeles, CA · May 6, 2012#28excellent 👏
why?harnett county NC · May 6, 2012#29keep us updated on the gas mileage. More low end torque is a good sign.
pennyracergrants pass · May 7, 2012#30okay i just called in my order to spencer at BeanGarage.com for the same header looks like a quality product the price was right and i hope to gain a tiny bit of power and mileage unit comes with exhaust donut but no header flange gasket not a problem
tooterThread starterLos Angeles · May 8, 2012#31 Originally Posted by TPA5 ↑
Gotta keep the little lady happy, cause if the missus ain't happy, no ones gonna be happy.
That reminds me of a friend of mine who said his wife told him:
"If I'm happy... you're happy."
...and she made it sound like a threat. 😆
I bought the car for my wife for our 20th anniversary, so even though it's her ride and she drives it more than I do, I still get the fun of pimping it out. 😉
Still, if your able an exhaust note video would be nice after. Did you find the sound changed much with the header/stock pipe combo?
No change... it sounds just like before. A video would be truly unimpressive. I think it didn't make any sound difference because the stock header was just two thin stamped metal sheets welded together around the edges. So the thin header tubes aren't any louder than that already was. The biggest difference is climbing a steep hill in second gear at 2,000 to 3,000rpm. It's noticeably stronger in that range. A nice low end sweet spot. Higher rpms there isn't a noticeable difference because the rest of the exhaust system is totally bone stock.
cali yarisCanoga Park, CA · May 8, 2012#32pennyracergrants pass · May 8, 2012#33ya i screwed up i did not see it for sale on the site i only seen the megan and dc header i would have been happy to give micro image the business i do have a question when will the under body panel kit be back in stock for the yaris hb ?
cali yarisCanoga Park, CA · May 8, 2012#34^ It's ok, I'm glad the thread got posted and I had a chance to promote the product too.
We just got confirmation on the correct Dzuz fasteners, so I should have a few complete kits soon -- just need to go over to the aircraft hardware store -- yeah, we do have one of those. 😆
why?harnett county NC · May 8, 2012#35 Originally Posted by
cali yaris ↑
was going to ask that question. Great price. save save save.
tooterThread starterLos Angeles · May 9, 2012#36 Originally Posted by
pennyracer ↑ ya i screwed up i did not see it for sale on the site i only seen the megan and dc header i would have been happy to give micro image the business.
I didn't see it listed at Micro Image either. For me it would be hard to beat buying out of state as it saved $18 in sales tax as well as free shipping.
malibuguyWestminster, MD · May 9, 2012#37 Originally Posted by
cali yaris ↑
i did. and i waited about 2-3weeks for a response and then got fed up and ourchased elsewhere
cali yarisCanoga Park, CA · May 9, 2012#38 For me it would be hard to beat buying out of state as it saved $18 in sales tax as well as free shipping.
It's an even better price to pick up with cash, no sales tax, and we are in SoCal. 👍
pennyracergrants pass · May 9, 2012#39in oregon we have no sales tax . just think of going to buy a new car and paying zero sales tax on it :) that is a nice perk not to pay sales tax from a vendor in ca if you live there most company's wont even consider that these days but cash is king in my book
tooterThread starterLos Angeles · May 9, 2012#40 Originally Posted by
cali yaris ↑ It's an even better price to pick up with cash, no sales tax, and we are in SoCal. 👍
Good point! 🙂
I'll certainly keep that in mind. Because I buy more stuff online than I do in person, it doesn't even occur to me.
cali yarisCanoga Park, CA · May 9, 2012#41@ pennyracer: I love that about Oregon
@ tooter: Definitely come by the shop sometime. No one leaves empty handed. :)
Sent a Weapon R header off today, thank you!
pennyracergrants pass · May 10, 2012#42does any one have the torque spec on the header flange bolts ?
cali yarisCanoga Park, CA · May 10, 2012#43tooterThread starterLos Angeles · May 10, 2012#44Hey Garm, speaking of studs... I notice that you have Ichiba spacer kits. Do you sell stud sets of 8 separately? If you do, how much are they?
pennyracergrants pass · May 10, 2012#45no numbers for me anybody :(
WeeYariGeorgetown, Ontario, Canada · May 10, 2012#46 Originally Posted by
pennyracer ↑ no numbers for me anybody :(
20 ft.lbs. according to factory service manual.
tooterThread starterLos Angeles · May 10, 2012#47All I know is thatToyota Camry 4 cylinder exhaust manifold bolt torque is 27 ft lbs. The bolts on my new Yaris weren't very tight and they were put on by the factory. I'd guess not over 20 ft lbs.
Hey Wee, you beat me to it! 🙂
tooterThread starterLos Angeles · May 10, 2012#48 Originally Posted by
cali yaris ↑ @ pennyracer: I love that about Oregon
@ tooter: Definitely come by the shop sometime. No one leaves empty handed. :)
Sent a Weapon R header off today, thank you!
You're right, Garm. I didn't leave empty handed. 😆
It was a pleasure meeting you and Jeff, and thanks for your good service!
cali yarisCanoga Park, CA · May 10, 2012#49ha, nice! I meant freebies which I'm quite sure we forgot to give you. 🙁
It's really great to meet our customers in real life - we obvously get a big kick out of it. (I gave tooter a long-ish tour of the shop and cars). Thanks!
blacksandiegovitzJust chillin' out brah ! · May 10, 2012#50 Originally Posted by
cali yaris ↑ ha, nice! I meant freebies which I'm quite sure we forgot to give you. 🙁
It's really great to meet our customers in real life - we obvously get a big kick out of it. (I gave tooter a long-ish tour of the shop and cars). Thanks!
^^ yeah I haven't been up to the shop in a while but its like a yaris candy store lol