Yarisworld Archive

2007 yaris cv passanger axle and cardone select cv axle picture )

23 posts · 15,653 views

yaris4062007Original postnorthern california · Apr 8, 2012#1
cardone select doesnt have rubber thing in the middle like the stock cv drive axle. Do I need it or not on cardone select.. thanx

Replies 22

yaris4062007Thread starternorthern california · Apr 8, 2012#2
stock cv axle and cardone new cv axle
014.jpg
yaris4062007Thread starternorthern california · Apr 8, 2012#3
pic
002.jpg
CTScottUSA, CT · Apr 8, 2012#4
That rubber thing is a vibration damper. There is only one on the right (longer) drive shaft.

I am not sure how much of a difference you will feel without it, so I think I would contact Cardone to see if they intentionally leave it off.
yaris4062007Thread starternorthern california · Apr 8, 2012#5
i noticed stock axles are little bit heavier then cardone select. I am just going to install it and see if it makes difference or not.. do i need to lubricate the inner cv joint with transmission fluid or white litium grease. if yes where do i lubricate on inner cv joint thread with c-clip and outer cv joint thread. thanx :)
CTScottUSA, CT · Apr 8, 2012#6
The inner should be lubed with ATF. Just dip your finger in it and coat the spline and snap ring before you insert the shaft. The service manual doesn't indicate lubing the outer spline.
yaris4062007Thread starternorthern california · Apr 8, 2012#7
Got it, thank you ;)
022.jpg
yaris4062007Thread starternorthern california · Apr 8, 2012#8
...
025.jpg
yaris4062007Thread starternorthern california · Apr 8, 2012#9
picture of inner cv joint 😉
004.jpg
CoryMWhite Rock BC · Apr 9, 2012#10
As mentioned the rubber is a vibration dampener. You should not notice any problems with it gone.
A little late, but for the next person; Put a little lube on the area where the seal rides on the inner CV axle. This way your seals are lubed from the start. Also, I see in the last pic you have the sharp axle splines resting on the seal. The idea is to not touch the seal with the splines at all. If the seal gets even a small nick, it will leak.
I typically use a bungee cord or strap to pull the knuckle assy back so I can get a straight shot at the transmission with the shaft.

Cheers,
Cory
auxmikeLI, New Yawk · Apr 9, 2012#11
I had to pull my axels to do a clutch swap on a '97 Saturn. Had the whole job done and buttoned up. Next day the freakin' axel seal leaked at the tranny side. Smoke all over from the oil landing on the hot exhaust. I almost broke my hand with a 3ft. pry bar doing the job. I was fed up and that's the day I said... F' this,I'm buying a new car.
Thus the new Yaris back in '08.....
yaris4062007Thread starternorthern california · Apr 9, 2012#12
Is it hard to replaces seal if it leaks. My car does viberate inside maybe i need wheel alignment. Next time i remove the cv axle i will make sure to grease seal ;). Thanx for info. :)
TRXPANAMA · Jun 4, 2012#13
I wonder if these axles are the same for a 2007 HB with a 1.3L engine? I need to replace the LH on mine, but the dealer wants $800.00 bucks.
CTScottUSA, CT · Jun 4, 2012#14
Originally Posted by TRX ↑
I wonder if these axles are the same for a 2007 HB with a 1.3L engine? I need to replace the LH on mine, but the dealer wants $800.00 bucks.
Do you have the 2NZFE or the 2SZFE and which transmission do you have?
jayycanada · Apr 11, 2013#15
did you need to remove both balljoints to get at the axle? and how did you get the axle out of the tranny ? please reply i really need to replace mines, thanksss
CTScottUSA, CT · Apr 11, 2013#16
Originally Posted by jayy ↑
did you need to remove both balljoints to get at the axle? and how did you get the axle out of the tranny ? please reply i really need to replace mines, thanksss
You just need to remove the ball joint on the side you are working on. For getting the axle out, there is a lip on the inner cup that you push or pull out by.

The left side is trickier than the right, as you have to pull that one out using something like the Toyota SST shown in the top image. The right is easy in that you can pull it out using a large screwdriver and a mallet.


Drive Shaft Removal.jpg
jayycanada · Apr 11, 2013#17
i REAAALLY apreciate the reply, im planning on removing the lower control arm balljoint, will i be able to get the axle out just by removing the lower control arm? and can the outer joint be removed from the axle by pounding it out wit a brass hammer(im trying to replace my outer joint on Passenger side)
CTScottUSA, CT · Apr 11, 2013#18
Originally Posted by jayy ↑
i REAAALLY apreciate the reply, im planning on removing the lower control arm balljoint, will i be able to get the axle out just by removing the lower control arm? and can the outer joint be removed from the axle by pounding it out wit a brass hammer(im trying to replace my outer joint on Passenger side)
To pull the hub off the axle I removed:

1. Tie rod end
2. Ball Joint
3. Stabilizer link (the strut support rod)

With those disconnected I was able to easy yank the hub off the outer spline. Then you just have to deal with popping the inner spline out.
jayycanada · Apr 11, 2013#19
sorry , that was a horibble explination on my part. what i was trying to say was, i dont have a ball joint remover, will taking just the lower control arm balljoint off enable me to remove the hub and have enough space to remove the axle out of the tranny ?
CTScottUSA, CT · Apr 11, 2013#20
Originally Posted by jayy ↑
sorry , that was a horibble explination on my part. what i was trying to say was, i dont have a ball joint remover, will taking just the lower control arm balljoint off enable me to remove the hub and have enough space to remove the axle out of the tranny ?
I don't believe so, unless maybe if you separate the knuckle from the strut. I found that I could separate the ball joint using just a plastic hammer.
jayycanada · Apr 11, 2013#21
sorry that was a horible explination on my part. what i was trying to say was, i dont have a balljoint tool. Will removing JUST the lower control arm balljoint enable me to remove the hub and have enough space to remove the axle out the tranny?
jayycanada · Apr 11, 2013#22
oh okay thanks alot
yaris4062007Thread starternorthern california · Apr 15, 2013#23
did you get it removed jayy??