lcastrobOriginal postcr · Jan 16, 2012#1hi all
i bought a kit from microimage, did the engine bay part ok but i dont know how to proceed in the interior and will really appreciate your help
the relay is installed in the right place
the switch has 3 cables coming out as the picture.
what i need to do with these 3 cables.???
1 attachment not included in this copy
Replies 10
OTA'sTOYHilo, Hawaii · Jan 16, 2012#2lcastrobThread startercr · Jan 16, 2012#3i am using those but im confused... please excuse me as i am rookie on this things
b. For the fogs to turn on with the parking lights, low beams or high beams connect the
outside red wire to pin 3 and the green wire next to it to pin 13 of Connector D4,
which is the headlight stalk connector
red wire? i only have one orange... and it has a strange connector that i dont know how to use.
i am supposed to cut the wires? or remove one wire and replace the other?
the black one has a different connector it looks like a ground you will connect to a bolt.
OTA'sTOYHilo, Hawaii · Jan 16, 2012#4lcastrobThread startercr · Jan 16, 2012#5thanks i think i almost got it...
1. remove pin 3 cable from D4 connector
2. connect the cable i just removed from D4 and connect it to my orange cable
3.connect my green cable to the pin 3
4. connect ground cable
am i correct?
i found the 2 set of instructions a litle different... did i receive an outdated switch?
woulndt i be missing the connection for the switch light?ç
also i would like help on how to remove the pin from D4 connector i tried but i was not able and i was afraid of breaking it.
i appreciate all the help at this moment i have my fogs in the bumper but no lights!
lcastrobThread startercr · Jan 17, 2012#6can someone confirm? i think im going to try tomorrow...
OTA'sTOYHilo, Hawaii · Jan 18, 2012#7 Originally Posted by
lcastrob ↑ thanks i think i almost got it...
1. remove pin 3 cable from D4 connector
2. connect the cable i just removed from D4 and connect it to my orange cable
3.connect my green cable to the pin 3
4. connect ground cable
am i correct?yes
i found the 2 set of instructions a litle different... did i receive an outdated switch?instuctions are good just the kit wiring changed colors
woulndt i be missing the connection for the switch light?çare you talking about the switch that comes with the kit?
also i would like help on how to remove the pin from D4 connector i tried but i was not able and i was afraid of breaking it.get yourself a paperclip and file the end into a angled tip use it to separate the terminal wire from connector
i appreciate all the help at this moment i have my fogs in the bumper but no lights!
.
OTA'sTOYHilo, Hawaii · Jan 18, 2012#8 Originally Posted by
lcastrob ↑ i am using those but im confused... please excuse me as i am rookie on this things
b. For the fogs to turn on with the parking lights, low beams or high beams connect the
outside red wire to pin 3 and the green wire next to it to pin 13 of Connector D4,
which is the headlight stalk connector
red wire? i only have one orange... and it has a strange connector that i dont know how to use.
i am supposed to cut the wires? or remove one wire and replace the other?
the black one has a different connector it looks like a ground you will connect to a bolt.
http://www.microimageonline.com/down...ts_install.pdf PAGE #4 red wire would need to be extended and routed up to steering column for foglight to be able to turn on with marker,low light and high light
lcastrobThread startercr · Jan 18, 2012#9thanks a lot man! i will try it and i hope soon ill post a success picture of my fog lights!!
lcastrobThread startercr · Jan 19, 2012#10omg !!!
today i came back from work, open everything... had my paper clip at hand and wasnt able to remove the pin...
im afraid of pulling too hard and leaving the connector but removing the wire...
any tips? i think i will have to ask a friend who has more experience on cars...
CTScottUSA, CT · Jan 19, 2012#11 Originally Posted by
lcastrob ↑ omg !!!
today i came back from work, open everything... had my paper clip at hand and wasnt able to remove the pin...
im afraid of pulling too hard and leaving the connector but removing the wire...
any tips? i think i will have to ask a friend who has more experience on cars...
I prefer an Xacto knife blade to a paperclip (if I don't have a proper pin popper). The tab that you are lifting is only in about 1/4". lift the pin lock tab and insert the blade in as shown below. I like to angle the blade towards the metal of the pin to get the blade to go on the correct side of the plastic tab (it is very easy to go above it, which makes it impossible to pull the pin). Once the blade is in position, lift the tip away from the metal pin and you will hear a slight click from the plastic tab. At that point the pin will easily slide out the back of the connector.
Picture not included in this copy1 attachment not included in this copy