Hello yojabbajabba. I have done this install and can offer some assistance.
First of all, I would recommend going with the Axxess Metra ASWC.
The ASWC install requires fewer steps but more importantly it seems to respond faster than the PAC SWI when you press a button on the steering wheel.
If your car came from the factory with steering wheel audio controls:
The spot that you would connect the steering wheel control interface to your Toyota Yaris is Connector D74 (Radio Receiver Assembly).
Connector D74 is one of three Radio Receiver Assembly wiring harnesses that can be located once your remove your stock head unit.
D74 may be plugged into the back of your stock head unit or it may be unplugged and found near the other two Radio Receiver Assembly wiring harnesses (D10 and D11, which would be connected to the back of your head unit).
To add either the Axxess Metra ASWC or PAC SWI you tap into the following three wires from connector D74:
Pin 6: SWG (ground)
Pin 7: SW1 (Steering1)
Pin 8: SW2 (Steering2)
Those three wires from Connector D74 connect back to to the Steering Wheel buttons via the Spiral Cable assembly connector D3 (located under the steering column):
Connector D3:
Pin 4: EAU (common/ground for steering wheel control)
Pin 5: AU2 (mode switch circuit)
Pin 6 AU1 (volume +/-, Seek +/- circuits)
The image below shows the two connectors:
Picture not included in this copy The diagram below shows how this circuit is wired together:
Picture not included in this copy If you are installing the Axxess Metra ASWC, you would wire it as follows:
1. Connect the Black wire of the ASWC to ground.
2. Connect the Red wire of the ASWC to a 12 volt accessory wire, one that turns on and off with the ignition key.
3. Connect the Green/Orange wire of the ASWC to Pin 7: SW1 (Steering1) on Connector D74 [which leads to Pin 6 (AU1) on Connector D3]
4. Connect the Black/Green wire of the ASWC to Pin 8: SW2 (Steering2) on Connector D74 [which leads to Pin 5 (AU2) on Connector D3]
5. Connect Pin 6: SWG (ground) on Connector D74 to ground
6. All other wires on the ASWC would be taped up (to avoid short circuits) as they are not used.
The reason I mentioned Connector D3 and included a diagram of the whole circuit is for those who wish to add steering wheel controls to a Yaris which did not come from the factory with Steering wheel controls.
Since mine did not come with the factory with Steering wheel controls, it was not pre-wired to support them at connector D74.
I was able to add the steering wheel controls by purchasing the missing pieces:
-Steering Wheel Switches - Toyota Name: Switch Assy. Toyota Part #: 84250-52010-C0
-Spiral Cable assembly - Toyota Name: Cable Sub-Assy. Toyota Part #: 84306-52090 (#09) G-BOOK
-New Airbag with smaller airbag cover that supports Steering Wheel Switches
-an old CD ROM cable from a computer. (Cable consisting of three twisted wires which was used to provide analog sound signal from the CD ROM drive to a sound card)
Once installed, I wired the Axxess Metra ASWC directly into Connector D3 (located below the steering column) since there was no wiring in my car that connected D74 back to D3.
The old CD ROM cable was used because it already had the small molex connectors crimped on to its three wires and could be easily inserted into connector D4 at one end.
The other end of the old CD ROM cable was cut off and connected to the Axxess Metra ASWC as detailed above.
I hope this information helps you. Please feel free to post back with any questions. Good luck with your installation
2 attachments not included in this copy