Yarisworld Archive

Painted Headlights

22 posts · 8,116 views

StoveOriginal postTigard Oregon · Sep 11, 2011#1
I haven't worked on my Yaris or been on here for quite a long time. I'm finally back to a place where I can work on my car. This weekends project was painting the unnecessary shiny bits in the headlight housings.
Before and after pics.

Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy

6 attachments not included in this copy

Replies 21

ilikericesavannah, ga · Sep 11, 2011#2
I have mixed feelings about this....
deathwisherBC · Sep 12, 2011#3
I think there has to be more "black" in your colour scheme to match those painted headlights.
NZ-FE ViosGeorgia · Sep 12, 2011#4
I like it. Get your windows tinted to match. But I think painted headlights always look good. Adds finer lines to the front end. Looks nice tho again. Cheers. Want to do mine?
yaris2010RSAngus, Ontario · Sep 12, 2011#5
u did a very nice job, if i didnt have to drive my car everyday i would definatly do this
KCALB SIRAYVirginia · Sep 12, 2011#6
Get some eye lids and I think it will look even better. Nice job!!
403RSCalgary, Canada · Sep 12, 2011#7
Would love to do this on my black pearl!
StoveThread starterTigard Oregon · Sep 12, 2011#8
Originally Posted by yaris2010RS ↑
u did a very nice job, if i didnt have to drive my car everyday i would definatly do this
Originally Posted by 403RS ↑
Would love to do this on my black pearl!
Its not that hard to do. I did one light on Saturday and the other on Sunday. It took me about 3.5 hours per light.

I used the HID Install thread to disassemble the light. Yaris LB HID Installation

Two differences, I didn't completely remove the front bumper, I left the bottom bots/fasteners in place and lightly pulled it out of the way to remove the light. I didn't bake/heat the light housings, I was able to work the lights apart and cut the sealant as I went.

FYI if you end up doing this:
The chrome finish on the housings is really easy to scratch. Wiping it with anything other than a really soft cloth will dull the finish and leave scratches. The masking tape didn't leave any blemishes but I was careful to place it and not move it when it was partially stuck down.

Finger prints are a pain to get off of the housing, don't touch any part that you aren't planning on painting and wear clean latex gloves while disassembling, masking and reassembling the light.
cali yarisCanoga Park, CA · Sep 13, 2011#9
excellent - I think it looks great.
bzinn 1University Place,WA · Sep 13, 2011#10
I like em.....looks really good.
catliektheifLeesburg, VA · Sep 13, 2011#11
Originally Posted by Stove ↑
I didn't bake/heat the light housings, I was able to work the lights apart and cut the sealant as I went.
how did you seal it back up?
StoveThread starterTigard Oregon · Sep 13, 2011#12
Originally Posted by catliektheif ↑
how did you seal it back up?
High Temp Silicone. I used it sparingly around the joint between the lens and the lower housing after I reassembled them. I wanted to be able to separate the parts easily if I decide later to add some LED's or do something else to dress them up little. If I end up with a little condensation in them, I'll pull them and reseal them.
JBougieBeech Bluff, TN · Sep 14, 2011#13
I painted mine also - and I took out the amber inserts .... with the amber being out of there, it really made a *huge* difference and made it look a *ton* better, IMO. Nice job though :)
NZ-FE ViosGeorgia · Sep 14, 2011#14
Originally Posted by JBougie ↑
I painted mine also - and I took out the amber inserts .... with the amber being out of there, it really made a *huge* difference and made it look a *ton* better, IMO. Nice job though :)
JBougieBeech Bluff, TN · Sep 14, 2011#15
haha fair enough ....

here is one from this morning (my car got wrecked, so its filthy and I just went out and snapped a shot real fast, so I apologize for the lack of quality photgraphy here...)

1 attachment not included in this copy

JBougieBeech Bluff, TN · Sep 14, 2011#16
lol - I am still in my PJs, I didn't notice that showed up in the pic. Oops. Oh well, I work from home - I have an excuse :P

Here is also a picture farther away:

1 attachment not included in this copy

NZ-FE ViosGeorgia · Sep 14, 2011#17
Looks so good. This mod has been around for at least a decade. Never ceases to amaze me how much a difference it makes. Cheers
JBougieBeech Bluff, TN · Sep 14, 2011#18
I had projectors, and they didn't work - and with the lack of aftermarket options available; I said "screw it" and just painted them. The car wasn't but a month old when I did it, and it was still wasn't set fully so I just pulled them apart with my hands and a pry tool; very little effort was involved in it. And just taping them off and I sprayed mine with black chrome which I think added a little bit of depth to it (I'm a nerd) and made it a bit different from the norm.

I love how they turned out, and now I will never replace them because I love them so much :)
Betriventedmonton · Sep 14, 2011#19
I'm glad I'm not the only one who thought "Why not just straight up retrofit to projectors?".

Great job, and that's exactly why I think you can do a real good retrofit.
JBougieBeech Bluff, TN · Sep 14, 2011#20
^ aren't retrofits HIDs? Maybe I'm just confused.
catliektheifLeesburg, VA · Sep 15, 2011#21
Originally Posted by JBougie ↑
lol - I am still in my PJs, I didn't notice that showed up in the pic. Oops. Oh well, I work from home - I have an excuse :P

Here is also a picture farther away:
your car is so tight.
Betriventedmonton · Sep 15, 2011#22
Originally Posted by JBougie ↑
^ aren't retrofits HIDs? Maybe I'm just confused.
Well retrofits are hids.. in the sense that they're MEANT for HIDs. You could very well run normal bulbs in a retrofit but that's kind of a huge waste.