Yarisworld Archive

Installed Rain Sensing Wipers Sensor

28 posts · 47,816 views

toy_torontoOriginal postTarrana, Canada · Aug 15, 2011#1
Since I couldn't find a cheap Prius stalk to replace the stock wiper arm for front intermittent delay, I ended up installing a 'Rain Tracker' rain sensing wipers control system (model RT-50A from http://www.raintracker.com)

The package arrived on Friday and I spent about 1 hr installing it today. I have to say I'm quite happy with the result -- check it out:


http://www.youtube.com/watch?v=woW1Z38GDok



-toy

Replies 27

ciscobearBarbados · Aug 15, 2011#2
Very neat, thanks for posting.......Any gotchas we should look for?
Lil AbnerDublin, Ohio · Aug 15, 2011#3
That's pretty slick!
toy_torontoThread starterTarrana, Canada · Aug 15, 2011#4
thanks 🙂

After the install we had a good thunderstorm / showers right after so I went for a drive. The sensor worked really well however I found the sensitivity a little less than I would've liked so I adjusted the sensitivity just a little (turned the pot 1/4 turn). Everything is all good now.

I'll upload another video later when I went for my drive so you can see how the wipers adjust themselves at the right speed.


-toy
AltitudeColorado · Aug 15, 2011#5
Nice. Does it have a defeat switch so you can disable it or does it only work when you turn your wipers on at least one click?
toy_torontoThread starterTarrana, Canada · Aug 15, 2011#6
Yes the module does have an ON/OFF switch so that you can bypass the system if you don't want it to be automatic (example: car wash).

The yaris wiper stalk remains in the OFF position as normal and can be used in parallel with the system if you like, so if you want extra wipes you can trigger the wipers manually.

Here's a good overview of the system for those thinking of getting one (installed ona tractor but the same idea):

http://www.youtube.com/watch?v=0c58Hu7XRf0


-toy
mazillaSan Jacinto California · Aug 15, 2011#7
I wonder how long the unit will last without issue...my only concern being the sensor.
eTiMaGoBangkok, Thailand · Aug 15, 2011#8
love the video, the car's like "hey quit it!" each time you spray it :D
toy_torontoThread starterTarrana, Canada · Aug 15, 2011#9
^ that's exactly what I thought, lol!

Originally Posted by mazilla ↑
I wonder how long the unit will last without issue...my only concern being the sensor.
I wonder myself. I think it's not too bad as they'll refund you within 30 days if you aren't satisfied plus the unit comes with a standard 3yrs warranty.


I'm holding on to my receipt! http://www.hydreon.com/warranty.php




-toy
mazillaSan Jacinto California · Aug 15, 2011#10
Originally Posted by toy_toronto ↑
^ that's exactly what I thought, lol!



I wonder myself. I think it's not too bad as they'll refund you within 30 days if you aren't satisfied plus the unit comes with a standard 3yrs warranty.


I'm holding on to my receipt! http://www.hydreon.com/warranty.php




-toy

A 3 year warranty is pretty good! You guys should in the harsher weather areas should be able to give it a run for it's money over three years...
AltitudeColorado · Aug 15, 2011#11
Where did you mount the sensor? Up near the rear view mirror like it shows on the site or somewhere else on the windshield?

The sensor looks kind of thick. What's your impression of it? Is it an eyesore?
toy_torontoThread starterTarrana, Canada · Aug 15, 2011#12
I mounted it just a bit to the left of the rear view mount because of the cable which I managed to tuck away underneath the headliner.

The sensor is about 1.75" x 1.75" and a little over half-inch thick. It might actually be slightly smaller than some of the OEM ones.

You don't actualy see it because it's behind the rear view mirror. From the outside, it looks like a rear-view mirror mount and not noticeable at all.



-toy
toy_torontoThread starterTarrana, Canada · Aug 15, 2011#13
I forgot to mention that the unit also comes with auto headlamp control built-in. Besides rain it can also sense light and will turn your headlights on automatically at night.

I'm going to have to get CTscott to help me figure out how to wire that part up. The manual specifically say the auto headlamp install should be attempted by the PROS only, that I am not 😆.


Here's the basic wiring hookup for the built-in head lamp control. I'm not sure how it ties in with the Yaris existing headlight relay system:

http://www.raintracker.com/docs/head...rol_rt-50a.pdf



-toy
CTScottUSA, CT · Aug 15, 2011#14
Originally Posted by toy_toronto ↑
I forgot to mention that the unit also comes with auto headlamp control built-in. Besides rain it can also sense light and will turn your headlights on automatically at night.

I'm going to have to get CTscott to help me figure out how to wire that part up. The manual specifically say the auto headlamp install should be attempted by the PROS only, that I am not 😆.


Here's the basic wiring hookup for the built-in head lamp control. I'm not sure how it ties in with the Yaris existing headlight relay system:

http://www.raintracker.com/docs/head...rol_rt-50a.pdf

-toy

You will follow the instructions for: -VEHICLE RELAY, GROUND SIDE CONTROL


The Yaris doesn't have a headlight on and then separate beam control switch, so you will use one relay to switch the light blue wire in pin 8 of the headlight stalk connector (low beams) to ground and the other relay to switch the white wire in pin 13 (tail lights) to ground.
landrym28Saint John, NB, Canada · Aug 15, 2011#15
That's pretty cool!
toy_torontoThread starterTarrana, Canada · Aug 15, 2011#16
Originally Posted by CTScott ↑
You will follow the instructions for: -VEHICLE RELAY, GROUND SIDE CONTROL


The Yaris doesn't have a headlight on and then separate beam control switch, so you will use one relay to switch the light blue wire in pin 8 of the headlight stalk connector (low beams) to ground and the other relay to switch the white wire in pin 13 (tail lights) to ground.

Thanks CTScott, so basically I'll need to get 2 relays:

- Use 1st relay to switch the Pin 8 (HL) to ground.
- Use 2nd relay to switch Pin 13 (B1) to ground.


Pins to GND:
Picture lost · i54.tinypic.com


-toy
CTScottUSA, CT · Aug 15, 2011#17
Originally Posted by toy_toronto ↑
Thanks CTScott, so basically I'll need to get 2 relays:

- Use 1st relay to switch the Pin 8 (HL) to ground.
- Use 2nd relay to switch Pin 13 (B1) to ground.


Pins to GND:
Picture lost · i54.tinypic.com


-toy
Correct if you have factory DRLs. If you don't then the tails are the opposite polarity and you have to provide +12V to pin 10 (T1) instead of a ground to 13 (B1).
toy_torontoThread starterTarrana, Canada · Aug 16, 2011#18
Originally Posted by CTScott ↑
Correct if you have factory DRLs. If you don't then the tails are the opposite polarity and you have to provide +12V to pin 10 (T1) instead of a ground to 13 (B1).
I do have factory DRLs however I disabled it, does this change anything? At any rate, I'll gather the relays/diodes I need and work on this sometime this week or next.

Can you kindly do one final review of what I'm about to do based on this diagram I created?

Many thanks again Scott 🙂


* Headlamp control status after low-light is detected by sensor -> Relays switch pin 13 (tail) and 8 (Low) to GND:

Picture lost · i54.tinypic.com


-toy
Lil AbnerDublin, Ohio · Aug 16, 2011#19
Nice diagrams!! Is there a sensitivity adjustment for the headlights?
CTScottUSA, CT · Aug 16, 2011#20
Originally Posted by toy_toronto ↑
I do have factory DRLs however I disabled it, does this change anything? At any rate, I'll gather the relays/diodes I need and work on this sometime this week or next.

Can you kindly do one final review of what I'm about to do based on this diagram I created?

Many thanks again Scott 🙂


* Headlamp control status after low-light is detected by sensor -> Relays switch pin 13 (tail) and 8 (Low) to GND:

Picture lost · i54.tinypic.com





-toy

Perfect.
toy_torontoThread starterTarrana, Canada · Aug 16, 2011#21
Originally Posted by Lil Abner ↑
Is there a sensitivity adjustment for the headlights?
Besides the sensitivity adjustment for rain/moisture detect in the sensor area, I can't find anything in the manual that mentions about sensitivity adjustment for ambient light unfortunately.


How the Rain Tracker Controls Headlamps
Really, really well. The Rain Tracker senses the ambient light level outside the vehicle, and turns
on the headlamps when it is dark, or when it is raining. Most US States require you to have your
headlamps on when it is raining, and it is simply a good idea.




Originally Posted by CTScott ↑
Perfect.
Great -- I will report my results later this week. 👍



-toy
toy_torontoThread starterTarrana, Canada · Aug 25, 2011#22
Came here to report that the auto headlamp feature works! The same sensor detects both ambient light and rain that automatically triggers the headlights when it gets dark out and/or when it rains.

The system allows you to install 2 switches: 1 to bypass rain sensing (comes with the kit), and another switch you need to buy seperately to bypass the auto headlights and disable these features anytime.

Thanks again CTScott!


-toy
Lil AbnerDublin, Ohio · Aug 25, 2011#23
Nice! I guess now it makes it tough for you to stalk people late at night.......
toy_torontoThread starterTarrana, Canada · Aug 25, 2011#24
Stalk people at night? No problem.

Solution: bypass switch 😁

Originally Posted by toy_toronto ↑
The system allows you to install 2 switches: 1 to bypass rain sensing (comes with the kit), and another switch you need to buy seperately to bypass the auto headlights and disable these features anytime.


-toy
dnagardToronto · Sep 27, 2011#25
I would like to know : How much drilling of the dash board is involved? Where is the best place to put the On/Off switch on the dash board? Does it take lot of space up?
How you do attach the sensor to windshield (glue or suction cup) as some glues for rear view mirrors can crack the windshield.
How you detach the plastic cover along the windshield (to run sensor wire from underneath the hood to the top of the windshield).
Is it snap on/off?
I tried to understand the writing diagram from the Rain Trackers site but, I am still confused with which wire to attach to which one and where those wires are located in the first place. 🤷
I would really appreciate all your help!
Thank you
dnagardToronto · Sep 27, 2011#26
@ toy_toronto,
In addition, to my previous question I was wondering if it was possible, if you were able to create a youtube video or photos outlining step by step directions. As I don't follow the writing instructions confidently.
toy_torontoThread starterTarrana, Canada · Sep 28, 2011#27
Originally Posted by dnagard ↑
@ toy_toronto,
In addition, to my previous question I was wondering if it was possible, if you were able to create a youtube video or photos outlining step by step directions. As I don't follow the writing instructions confidently.

I would but it has been quite busy for me lately. Work and life in general have been getting in the way of me tweaking the Yaris.

It might seem confusing /overwhelming right now as you might think it is but it really is not difficult, plenty of help around here to get you through and the device comes complete with good documentation. Read this entire thread from the start and things will begin to make sense even more especially once you get a hold of the unit.

As for the switch and drilling it's more of a personal preference. I put the switch that came with the unit around the parking brake console (drilled ¾” hole).


Picture lost · i55.tinypic.com



-toy
dnagardToronto · Sep 29, 2011#28
at toy_toronto
Thanks, I will order Raintracker system.