Yarisworld Archive

Advice on Blitz S/C

89 posts · 32,518 views · page 2 of 2

Replies continued

MGarganoThread starterNJ · Jul 11, 2011#51
Originally Posted by Bluevitz-rs ↑
Then the problem I most definitely hardware related to what you installed. If there a leak anywhere the will not run
That's what I'm figuring. I'm taking the whole thing out now and keeping my fingers crossed the car runs properly when I'm done.
MGarganoThread starterNJ · Jul 11, 2011#52
Ladies and gentlemen- we have BOOST! Not! Gotcha!

But I pulled everything back out and returned the car to OEM and it's running without an issue!
MGarganoThread starterNJ · Jul 11, 2011#53
Ladies and gentlemen- we have BOOST! Not! Gotcha!

But I pulled everything back out and returned the car to OEM and it's running without an issue!
Bluevitz-rsOshawa, Ontario, Canada · Jul 11, 2011#54
So there must have been a leak or something letting in un-metered air. Or you had the MAF installed backwards LOL.
Focus_Sh1ftNew Jersey · Jul 12, 2011#55
If I let off the throttle, the RPMs nose-dive and the car stalls.
Agreed with Bluevitz; You're letting unmetered air in somewhere, the engine runs lean then dies. It'll be especially noticable while simply idling as compared to driving.

Too bad you don't live a little more north 😉
MGarganoThread starterNJ · Jul 12, 2011#56
CTScott has been helping me with some suggestions privately and he believes the cause of the problem was the intake manifold gasket that came with the Blitz kit. The one I received was tan and papery (CTScott's was metal) and was used by the kit's previous owner, but I assumed I could reuse it.

It's the only thing either of us could think of. The vacuum hoses were all connected correctly and the wiring obviously wasn't the problem, since the problem continued after I cut all the wiring out. The MAF was connected to the AFE intake as it has been for about two years now, so it couldn't have been that. The only thing that makes sense is the intake manifold gasket, right?
Bluevitz-rsOshawa, Ontario, Canada · Jul 12, 2011#57
I guess you didn't add any silicone to the gasket when you installed it. The other two entry points would be the top of the unit where the intake is and then further down where the throttle body bolts on.
borozinskiLittle Rock, AR · Jul 12, 2011#58
I was just gonna ask if you guys who have done the supercharger install use silicone. Sounds like it's a good idea from what happened with you. Sucks it happened, but it good for others to hear. It's made my mind up though, to use it. I have a weapon r themal gasket that goes inbetween the intake manifold and the head. I'm wondering if it'd be a bad idea to sandwich that in with silicone. I wanna keep it, since I know I wouldn't even get close to the money I paid for it.
MGarganoThread starterNJ · Jul 12, 2011#59
Originally Posted by Bluevitz-rs ↑
I guess you didn't add any silicone to the gasket when you installed it. The other two entry points would be the top of the unit where the intake is and then further down where the throttle body bolts on.
The kit was partially assembled when I received it, so the compressor was already mounted tightly to the intake manifold and I didn't mess with it for fear of breaking any seals and creating a leak.

The throttle body was bolted on just as tightly as it is to the OEM manifold now, so that really only leaves the intake manifold gasket, which I did not use silicone or any kind of gasket sealer on. I assumed it didn't need sealer, since the OEM one doesn't and it didn't look like the previous owner had used any either.
Bluevitz-rsOshawa, Ontario, Canada · Jul 12, 2011#60
The OEM one is like a giant O-ring though. If the one you're using is paper, then there could be high and low spots on it from being used already.
MGarganoThread starterNJ · Jul 12, 2011#61
Originally Posted by Bluevitz-rs ↑
The OEM one is like a giant O-ring though. If the one you're using is paper, then there could be high and low spots on it from being used already.
Agreed. This definitely seems like the most likely culprit. Any idea where I can find another gasket for this kit? And is the metal one a better idea than the paper?
borozinskiLittle Rock, AR · Jul 12, 2011#62
I know you guys are talking about the Blitz kit, but the Greddy instructions say to use silicone on it. Just throwing it out there, lol.
Bluevitz-rsOshawa, Ontario, Canada · Jul 12, 2011#63
Yeah, just put an 1/8 inch bead of RTV silicone on the gasket, on both sides and around each port and put it back on.
MGarganoThread starterNJ · Jul 12, 2011#64
Originally Posted by Bluevitz-rs ↑
Yeah, just put an 1/8 inch bead of RTV silicone on the gasket, on both sides and around each port and put it back on.
Use the same paper gasket? Or should I try to find a new one?
Focus_Sh1ftNew Jersey · Jul 12, 2011#65
As long as there's no cracks or obvious damage then you can reuse the old one. The key part is definitely the addition of silicone though. I've reused my turbo oil gaskets without any problems - but I always added some silicone when reapplying.
MGarganoThread starterNJ · Jul 12, 2011#66
Thanks for the info guys. I feel confident this gasket was definitely the problem. If it's possible, I'd like to be on the safe side this time and pick up a new gasket. Any idea where I can get one?
Bluevitz-rsOshawa, Ontario, Canada · Jul 12, 2011#67
You should be able to get one at your local car parts store. I'd still use a thing layer if silicone on a new gasket just to be certain. <-- if it's paper. A metal type one shouldn't require anything.
MGarganoThread starterNJ · Jul 12, 2011#68
All I'm seeing are the OEM o-ring style gaskets from local stores, not the flat type that came with the Blitz kit.
MUSKOKA800Chatham, Ontario, Canada · Jul 12, 2011#69
The Blitz offering is paper.
The oem gasket is a plastic seal that sits in a groove within the plastic intake (just bought one and found out the hard way. Actually less the CDN$7.00 which surprized me).
Go to a performance shop and buy gasket paper material to make you own (grade 9 auto shop) if Blitz cannot be contacted to supply one. They do seem to be MIA as the website shown on the instruction manual is not valid.
MGarganoThread starterNJ · Jul 13, 2011#70
Originally Posted by MUSKOKA800 ↑
The Blitz offering is paper.
The oem gasket is a plastic seal that sits in a groove within the plastic intake (just bought one and found out the hard way. Actually less the CDN$7.00 which surprized me).
Go to a performance shop and buy gasket paper material to make you own (grade 9 auto shop) if Blitz cannot be contacted to supply one. They do seem to be MIA as the website shown on the instruction manual is not valid.
Thanks for the info. I'm going to contact Garm to see if he can help me source one of the Blitz gaskets.
cali yarisCanoga Park, CA · Jul 13, 2011#71
Blitz USA is no more, all parts must be sourced from Blitz in Japan. I will inquire about it, but this is not something you'd get quickly. I will also look in my spare parts box and see if there is some magic in there. 👍
MGarganoThread starterNJ · Jul 13, 2011#72
Originally Posted by cali yaris ↑
Blitz USA is no more, all parts must be sourced from Blitz in Japan. I will inquire about it, but this is not something you'd get quickly. I will also look in my spare parts box and see if there is some magic in there. 👍
Thanks Garm. I wasn't aware Blitz USA was no more and I would assume a little thing like the from Japan would take forever and probably wouldn't be worth it. I was hoping someone had an extra laying around they wouldn't mind parting with. 🤷
borozinskiLittle Rock, AR · Jul 13, 2011#73
Just use some black rtv. The greddy kit only calls for sealant and doesn't even have any gaskets. It'd be cheaper that way to and less time to wait.
LtNoogieWest Hills, CA · Jul 16, 2011#74
If air is leaking in behind the intake manifold, wouldn't that be readable as low vacuum on any hose behind the throttle body?

After you make your new gasket and if you have the same problem, I sugget you put a vacuum gauge on a hose to confirm.
MGarganoThread starterNJ · Jul 16, 2011#75
Originally Posted by LtNoogie ↑
If air is leaking in behind the intake manifold, wouldn't that be readable as low vacuum on any hose behind the throttle body?

After you make your new gasket and if you have the same problem, I sugget you put a vacuum gauge on a hose to confirm.
In all honesty, if I go through all the trouble of re-installing the kit (using RTV on the gasket) and end up having the same problem, it's coming right back off and going up for sale. 🙁
PETERPOOPOahu · Jul 16, 2011#76
You probably should figure it out and not sell it. People might think something is wrong with the kit.
MGarganoThread starterNJ · Jul 16, 2011#77
Originally Posted by PETERPOOP ↑
You probably should figure it out and not sell it. People might think something is wrong with the kit.
I thought of that right after I posted my last message
Focus_Sh1ftNew Jersey · Jul 16, 2011#78
Don't give up!
MGarganoThread starterNJ · Jul 17, 2011#79
Originally Posted by Focus_Sh1ft ↑
Don't give up!
I really don't want to, especially after the money I coughed up for this thing, but it's hard since it's my only car and I need it for work everyday.
cali yarisCanoga Park, CA · Jul 17, 2011#80
Maybe a few days car rental can be part of the budget? ...just suggesting....
MGarganoThread starterNJ · Jul 17, 2011#81
Originally Posted by cali yaris ↑
Maybe a few days car rental can be part of the budget? ...just suggesting....
Definitely an option. I'm sure I'll get it done one way or another, and hopefully sooner rather than later. Besides, I'm saving that budget for a few of those sweet AEM gauges of yours, and hopefully one of those S/C engine covers you used to carry?
PETERPOOPOahu · Jul 17, 2011#82
I have one of those S/C engine covers. Black. Used once (believe it or not). I preferred to not have it. Let me know if you want it. PM me.
cali yarisCanoga Park, CA · Jul 17, 2011#83
no more unfinished aluminum ones, only black and red here. P-poops will be the best deal!
kelevraEmpire State · Dec 26, 2011#84
Great thread, I'm a learnin' :-)
CTScottUSA, CT · Dec 22, 2012#85
Originally Posted by Tima122 ↑
Привет.
Привет. Таковы некоторые серьезные датчиков. Есть ли у вас турбо нагнетателя или на yoir Bb?
yarisugiハワイ · Dec 22, 2012#86
xB? lots of gadgets :)

я сиськи люблю
Bluevitz-rsOshawa, Ontario, Canada · Dec 23, 2012#87
English translation anyone for the english speaking forum?
yarisugiハワイ · Dec 23, 2012#88
Copy/paste the sentences in Google translate from Russian to English and you'll understand most of it.
(except for that last sentence "gas distribution shaft"? I would assume as some kind of fuel rail?)