Yarisworld Archive

center bore on wheels is too big

17 posts · 15,504 views

DperryOriginal postbushkill, pa · May 12, 2011#1
ok so i just got my nice new rota wheels and relized that the center bore is a lot bigger . i test fitted the rim and its "loose" or has some play . the hub on the rotas is 67.1. so now im lost and dont know wut to do...do they make rings or hub adapters....need advice.

Replies 16

BluYrsTallinn, Estonia · May 12, 2011#2
There are spigot rings for that. They're basically plastic rings which make the centre bore smaller and they come in a variety of sizes. If I'm not mistaken, the center bore on the yaris is 54,0 (someone corrent me on this) so you need 67,1 to 54,0 rings for your wheels.
skootdogBaton Rouge,La · May 12, 2011#3
I got some rota's too and bought some rings off E-Bay for like ten bucks
skootdogBaton Rouge,La · May 12, 2011#4
Yes 54.1mm is correct
DperryThread starterbushkill, pa · May 12, 2011#5
thanks guys...i found wut i was lookin for right after i posted this...hubcentric rings. now heres the real question do u think my local tire and wheel shop (jackwilliams) will have the rings i need
WeeYariGeorgetown, Ontario, Canada · May 12, 2011#6
^ walk in and find out
thebarberGrand Rapids, MI · May 12, 2011#7
you can drive w/o hubcentric rings on the wheels.....the lugnuts should be tapered at the end, just make sure you put them on evenly and itll space the wheel correctly on the hub
HTM Yarissouth Carolina · May 12, 2011#8
I would get metal rings if I were you , just to eliminate any possibility of melting . Yes I have melted them before . Discount tire direct has the metal rings for $15 ...
Jason@SportsCarDebary, FL · May 12, 2011#9
Originally Posted by Dperry ↑
ok so i just got my nice new rota wheels and relized that the center bore is a lot bigger . i test fitted the rim and its "loose" or has some play . the hub on the rotas is 67.1. so now im lost and dont know wut to do...do they make rings or hub adapters....need advice.
You don't need the wheels to be hub-centric, your lugs will do the job.
severous01SE Texas · May 12, 2011#10
so.....as long as the lug holes are right they'll suck it up to the hub where it's supposed to be. as long as you dont torque one lug then the next. you gotta tighten them all to touching, then torque them.
Jason@SportsCarDebary, FL · May 12, 2011#11
Originally Posted by severous01 ↑
so.....as long as the lug holes are right they'll suck it up to the hub where it's supposed to be. as long as you dont torque one lug then the next. you gotta tighten them all to touching, then torque them.
I just zip mine on with a cordless drill, then Tq them down with a wrench. No big deal.
DperryThread starterbushkill, pa · May 14, 2011#12
i got some hubcentric rings from the local custom shop it was 12 bucks no biggie...if they melt then ill graduate to metal
thepartsmancomethmidwest · May 14, 2011#13
most wheels get balanced mounted in the hub opening; BMW on the other hand has a special tool that goes through the lugstud holes to avoid any centering issues with the hubs when balancing. as long as nuts are on evenly, you are good to go. (good enough for BMW, good enough for me! lol)
ViperoniBrampton, ON · May 14, 2011#14
Originally Posted by Jason@SportsCar ↑
I just zip mine on with a cordless drill, then Tq them down with a wrench. No big deal.
QFT

Also, for centering rings, the best ones are polycarbonate, because they won't melt like plastic or rust on like metal rings.
TrashCan MonsterUnited States · May 19, 2011#15
aren't the metal rings that are used aluminum? those shouldn't rust anyway.
YaristeveLos Angeles · May 19, 2011#16
Originally Posted by TrashCan Monster ↑
aren't the metal rings that are used aluminum? those shouldn't rust anyway.
The rings won't rust but through galvanic corrosion they will attach themselves to the hubs. I had a set of aluminum rings in my Volk TE-37 on my Miata. I did not buy the caps so eventually one of the rings "welded" itself to the hub. It took about half an hour with a hammer and chisel to finally pry it off.

After that experience, I took a closer look at the rings, and IMO, they are totally unnecessary. Tapered lugs will center your wheels fine. Shanked lugs will center your wheels fine. If your wheels are made so badly that the lugs do not center the wheel, adding rings won't help since, if you install metal hub centering rings, the lugs will no longer seat correctly.

On my Volks, the lugs center the wheel so perfectly that when the lugs are torqued down, the hub centering ring is loose in the bore and can be spun inside the bore with my finger. You're better off spending the money buying the center caps (if they aren't included); then you won't get water in there causing the brake hat or drum to rust to the hub.
thepartsmancomethmidwest · May 20, 2011#17
if you want a fun experience with galvanic corrosion, try to take the rear wheels off a dually truck.....