Yarisworld Archive

JUN Cams for 1NZ-FE

29 posts · 34,997 views

Replies 28

Bluevitz-rsOshawa, Ontario, Canada · Mar 22, 2011#2
They look like they have a LOT more duration.
Flipper_1938Kentucky · Mar 22, 2011#3
Did it use the stock cam followers?

How does it run?
Dylan YapThread starterSingapore · Mar 22, 2011#4
it is plug and play.

dur 66 valve lift 9.5mm
cali yarisCanoga Park, CA · Mar 22, 2011#5
^ before and after dyno would be good to see.

By the way guys, these cams are over $800... EACH. 😲
Dylan YapThread starterSingapore · Mar 22, 2011#6
Originally Posted by cali yaris ↑
^ before and after dyno would be good to see.

By the way guys, these cams are over $800... EACH. 😲
ya thanks to the high jap Yen now sadly. but i am selling them like well in my country even with this price tag
Dylan YapThread starterSingapore · Mar 22, 2011#7
Please Note Result varies from car to car, engine to engine.

the car
Picture not included in this copy
the Power BHP
Picture not included in this copy
the Torque Nm
Picture not included in this copy

Thick solid Blue / Green is after tuning
Dotted Blue / Green is before

The test car is a Auto Vios,
Parts on the car:
1) Speed-d 4-1
2) HKS Hi-Power Muffler
3) Unichip Q
4) SS drop in Filter ( Stock Airbox)
5) CAI

Condition of car:
1) Mobil One EO 5000Km old
2) Denso Iridium spark plug (Not New)
3) 92 Fuel ( Last minute try our best to mix with 98 Fuel)

I was happy with 141bhp on crank for a Auto Vios. i expect more for MT vios.

Dyno is Dynopack TCF is set at 1.2 for auto
cali yarisCanoga Park, CA · Mar 22, 2011#8
Looks like a gain of about 14 hp and 20 torque, yes?

I don't think a stock ECU could handle this mod, you'd have to tune the car with management like this Vios was.
ilikericesavannah, ga · Mar 22, 2011#9
would you say these cams are tunable for boost? if i got these cams and then later boosted on top of them, could i tune it also? or is the lift and dur on these cams specific to N/A tunes?
Jason@SportsCarDebary, FL · Mar 22, 2011#10
I seem to recall the early posts about Jun cams listing three different sets of specs, with this one being the most mild. My math, and memory, may be a bit fuzzy... But I come up with this as a .354 lift, that is not much more than stock. 🤷


This is what is listed on the Jun website.
63 (252) 9.0 9.0 IN IN 1004M-T031 1004M-T031 JPY42,000 JPY42, 000 Can use with stock ECU Can use with stock ECU
EX EX 1004M-T131 1004M-T131 JPY42,000 JPY42, 000

* * The amout of lifts shows the cam lift. * The amout of lifts shows the cam lift.

Jason@SportsCarDebary, FL · Mar 22, 2011#11
Where is the rest of the screen, RPM, AFR?

Originally Posted by Dylan Yap ↑
Please Note Result varies from car to car, engine to engine.

the car
Picture not included in this copy
the Power BHP
Picture not included in this copy
the Torque Nm
Picture not included in this copy

Thick solid Blue / Green is after tuning
Dotted Blue / Green is before

The test car is a Auto Vios,
Parts on the car:
1) Speed-d 4-1
2) HKS Hi-Power Muffler
3) Unichip Q
4) SS drop in Filter ( Stock Airbox)
5) CAI

Condition of car:
1) Mobil One EO 5000Km old
2) Denso Iridium spark plug (Not New)
3) 92 Fuel ( Last minute try our best to mix with 98 Fuel)

I was happy with 141bhp on crank for a Auto Vios. i expect more for MT vios.

Dyno is Dynopack TCF is set at 1.2 for auto
cali yarisCanoga Park, CA · Mar 22, 2011#12
Here is the data I got when I considered stocking these:

1. 256 duration, 9.0mm lift (Street)
2. 272 duration, 9.5mm lift (NA)
3. 272 duration, 10.5mm lift (Turbo)
ilikericesavannah, ga · Mar 22, 2011#13
^woot woot^ thats what i was looking for.. and also, i do remember seeing that in another jun thread
Dylan YapThread starterSingapore · Mar 23, 2011#14
i dont do turbo car so i am not sure. this is what i request from JUN, the 3 spec mention

1. 256 duration, 9.0mm lift (Street)
2. 272 duration, 9.5mm lift (NA)
3. 272 duration, 10.5mm lift (Turbo)

also avaliable.


this one i install is 264dur 9.5mm valve lift.
i want a bolt-on thus i am not going for anything wild. stock lift is 9mm

Stock ECU can run the cams, but advise to add tuning to max on the result.

AFR i am running 13.3 for NA

note i am just sharing...not selling... too far haha
rapev-8WI · Mar 25, 2011#15
Originally Posted by Dylan Yap ↑
i dont do turbo car so i am not sure. this is what i request from JUN, the 3 spec mention

1. 256 duration, 9.0mm lift (Street)
2. 272 duration, 9.5mm lift (NA)
3. 272 duration, 10.5mm lift (Turbo)

also avaliable.


this one i install is 264dur 9.5mm valve lift.
i want a bolt-on thus i am not going for anything wild. stock lift is 9mm

Stock ECU can run the cams, but advise to add tuning to max on the result.

AFR i am running 13.3 for NA

note i am just sharing...not selling... too far haha
so i will able to run with my basic bolt on and the 9.5mm cam with my stock ecu on my 2010 5 speed?
cali yarisCanoga Park, CA · Mar 25, 2011#16
^ They say so, but do you want to pay $1700 to find out if you get a CEL or not?

I haven't seen an example where they just bolt on the cams, go drive the car hard, and show that the stock ECU has no problem with that.

Trust me, I want it to be true as much as anyone.
rob323Joyner, Brisbane · Mar 28, 2011#17
Did you have to re do the clearances with new buckets and shims?
Dylan YapThread starterSingapore · Mar 28, 2011#18
Originally Posted by rob323 ↑
Did you have to re do the clearances with new buckets and shims?
Dont need, as this are bolt-on Cams. Just plug & play
rob323Joyner, Brisbane · Mar 28, 2011#19
But a 1NZ-FE doesn't have hydraulic lash adjusters or adjustable tappets, you should still re-shim the buckets to get the clearances correct.
Dylan YapThread starterSingapore · Mar 28, 2011#20
Originally Posted by rob323 ↑
But a 1NZ-FE doesn't have hydraulic lash adjusters or adjustable tappets, you should still re-shim the buckets to get the clearances correct.
You need to do this IF you are going for spec higher than what i have. What i using is bolt-on JUN cams 264 - 9.5 mm
Jason@SportsCarDebary, FL · Mar 29, 2011#21
Originally Posted by Dylan Yap ↑
You need to do this IF you are going for spec higher than what i have. What i using is bolt-on JUN cams 264 - 9.5 mm
There are like 16 different OE bucket part numbers (in varying thickness) for use with the stock cams. Build tolerances within the head, valves, cam and bearings are enough to require a bucket change with just a stock cam replacement. 🤷
rob323Joyner, Brisbane · Mar 29, 2011#22
My point exactly, you can't even use a stock cam from another motor without having to redo the clearances.
Jason@SportsCarDebary, FL · Mar 29, 2011#23
Originally Posted by rob323 ↑
My point exactly, you can't even use a stock cam from another motor without having to redo the clearances.
I am sure its fine, just send your $30k to me, I will send you a set of magic cams and a cashiers check for the balance. 😆
rob323Joyner, Brisbane · Mar 29, 2011#24
No thanks, I'll do it myself so I know it's done right.
vitz rsSingapore · Apr 6, 2011#25
Originally Posted by Dylan Yap ↑
You need to do this IF you are going for spec higher than what i have. What i using is bolt-on JUN cams 264 - 9.5 mm
Hi Bro, I am driving vitz rs.
just wondering where is your workshop?
Dylan YapThread starterSingapore · Apr 13, 2011#26
Originally Posted by vitz rs ↑
Hi Bro, I am driving vitz rs.
just wondering where is your workshop?
Pmed you my address... great to find someone from SG here😁
vitz rsSingapore · Apr 13, 2011#27
Originally Posted by Dylan Yap ↑
Pmed you my address... great to find someone from SG here😁
U got mail bro.
rob323Joyner, Brisbane · Apr 19, 2011#28
I see these cams are now available on Yahoo Japan.😉
speed1Lecco-Italy · May 11, 2011#29
I read all of your stories.
Super Mega cams for 1nzfe.
If u look at Jun site there are only 2 specs for 1nzfe:
9,0-63 (bolt-on series) and 9,5-66 (regular series).
If 9,5-66 rev limit move e vvt-i manage required
to have best.