Yarisworld Archive

Blower motor officially not working

15 posts · 32,009 views

waydizzyOriginal postCA · Mar 9, 2011#1
Hello all,

The blower motor in my '07 Yaris has stopped working completely. When it first stopped working, I could take the glove box out and start it spinning manually, and it would be fine until I turned the car off. Now it's kaput.

Might I need to replace the whole blower motor, or could it just be the relay? (I promise I did a big google/site search, but I didn't find exactly what I was looking for...) I'm not great at repairing cars, but I think I could do either one on my own...

Thanks for your help!

Replies 14

CTScottUSA, CT · Mar 9, 2011#2
Start by checking the following:

1. 40A HTR Fuse (power feed for the blower motor)- It's one of the large ones in the middle of the under hood fuse panel.

2. 10 GAUGE Fuse (power feed for the HTR relay coil)- In the under dash fuse panel.
waydizzyThread starterCA · Mar 10, 2011#3
I will get right on that. :) Thanks for your help!
waydizzyThread starterCA · Mar 22, 2011#4
Well, the fuses look great. Any suggestions on what to check next?

Thanks again!
CTScottUSA, CT · Mar 22, 2011#5
Originally Posted by waydizzy ↑
Well, the fuses look great. Any suggestions on what to check next?

Thanks again!
First, try pulling the larger connector (4 pin) from the bottom of the blower motor, then with the ignition on, put the blower up to the highest setting and see if it comes on.

Second, with that reconnected, remove the small storage cup to the lower left of the steering column, turn the ignition on, stick your ear by the fuse panel, and listen for the HTR relay to click when you turn the blower switch from off to on an back to off.

Also, do you have a multimeter? The next step after this would be to start taking some voltage measurements to see where the power feed stops.
AltitudeColorado · Mar 23, 2011#6
Originally Posted by waydizzy ↑
When it first stopped working, I could take the glove box out and start it spinning manually, and it would be fine until I turned the car off. Now it's kaput.
Assuming the blower motor has brushes, maybe they're burnt.
Ray TurnerTexas · Feb 23, 2013#7
I worked on a 2007 Yaris this afternoon. It only has a two wire connector on the bottom of the blower motor, not a 4 pin connector. I had no power to the blue wire or the black wire with the key on. All the fuses under the hood Ohmed out good.
CTScottUSA, CT · Feb 23, 2013#8
Originally Posted by Ray Turner ↑
I worked on a 2007 Yaris this afternoon. It only has a two wire connector on the bottom of the blower motor, not a 4 pin connector. I had no power to the blue wire or the black wire with the key on. All the fuses under the hood Ohmed out good.
The other connector, which is the blower resistor (for the speed control) has four pins. The blower resistor has a built in fuse, which is why I suggested to the O.P. above to pull the connector from it and put the fan on its highest setting, which bypassed the resistor.

Did you check the fuses that I mentioned above? One of the two is under the dash, not under the hood.
Kesa091518Ohio · Aug 31, 2021#9
CTscott. Followed your advice. Removed 4 pin and blower worked briefly on highest setting before stopping. Guessing I need to replace my blower resistor then? Any advice on how to reach that panel behind the dash? You have been so helpful thanks! 07 Yaris.

Also, since it only worked briefly when I bypassed the resistor, did I blow another fuse?

Thanks again
Kesa091518Ohio · Sep 2, 2021#10
I actually replaced the resistor and when I turned the ignition and blower on, it did the same thing. Motor Whirled around for a few seconds then stopped. Any new suggestions? Could use the help. Thanks!
rayfloyd170SAUDI ARABIA · May 28, 2023#11
Originally Posted by Kesa091518 ↑
I actually replaced the resistor and when I turned the ignition and blower on, it did the same thing. Motor Whirled around for a few seconds then stopped. Any new suggestions? Could use the help. Thanks!

Hi, did you solve this problem?

I am guessing it has worn-out carbon brushes.
I am also expecting the same thing will happen to mine.
I am just starting with the intermittent whirling noise and decreased air flow then slight tapping the bottom makes it go back to normal airflow.

I dont know if the blower motor is serviceable like we can replace the internal brushes or they are just disposable.
CompeerAuckland, NZ · Nov 8, 2023#13
Originally Posted by rayfloyd170 ↑
Finally, i have realized this can be repaired eternally but the question is do you want to repair it considering the cost of a new blower motor is so cheap for a knock off brand?

check the link on my repair. i made this as spare as i already replaced with a genuine denso motor

Can somebody share the dimension of carbon brush used in denso AC/heater blowers
Honestly I'd rather get one from a the wreckers thats mint than get a knock off brand.

The toyota one will be better quality.
bairjoNov 22, 2023#14
screw that. You must be unemployed or retired to chase down an old used blower instead of a nice new blower. They are so easy to replace even if you did it every year.
CompeerAuckland, NZ · Nov 25, 2023#15
Originally Posted by bairjo ↑
screw that. You must be unemployed or retired to chase down an old used blower instead of a nice new blower. They are so easy to replace even if you did it every year.
Chase down? its the same blower in sooo many toyotas. And they almost never fail, why pay more for something that already exists in abudance and is made by toyota.

If you get one a new toyota one and its reasonable price makes sense, but otherwise id always rather use toyota over chinese imitation.