NipsOriginal postUK · Jan 29, 2011#1Replies 17
WeeYariGeorgetown, Ontario, Canada · Jan 29, 2011#2You can get away with stock studs for 5mm (though I'm not recommending it). 10mm will require longer studs.
NipsThread starterUK · Jan 29, 2011#3 Originally Posted by
WeeYari ↑ You can get away with stock studs for 5mm (though I'm not recommending it). 10mm will require longer studs.
Ok thanks, the studs are on the hub so what will i need to buy to add 10mm spacers
other cars i have had you just by longer bolts/nuts
severous01SE Texas · Jan 29, 2011#4if your'e doing the 10mm inthe rear why not do the penguin spacer back there and not between the rim and drum.
the penguin spacer goes behind the backing plate. can be installed permanently in less than 30 minutes (assuming you inow what you're doing...), and dont damage/threaten the studs in any way. you can even go 13mm if you want
AltitudeColorado · Jan 29, 2011#5 Originally Posted by
severous01 ↑ if your'e doing the 10mm inthe rear why not do the penguin spacer back there and not between the rim and drum.
the penguin spacer goes behind the backing plate. can be installed permanently in less than 30 minutes (assuming you inow what you're doing...), and dont damage/threaten the studs in any way. you can even go 13mm if you want
+1 - Go Penguin.
NipsThread starterUK · Jan 30, 2011#6Ok, Penguin it is.
Just sent an email to micro image for shipping cost to the uk
Thanks for you help guys
NipsThread starterUK · Jan 30, 2011#7I'm now thinking of getting 10mm Ichiba Wheel Spacers for the front and 13mm penguins for the rear would this be a good set up for standard 17" SR wheels without any rubbing or catching?
cali yarisCanoga Park, CA · Jan 30, 2011#8^ this depends on the offset of the wheel and the tire being used, and also camber. A little negative camber goes a long way to eliminate rubbing (and improves handling too!).
It may be necessary to trim some fender liner away in spots to eliminate any rubbing.
NipsThread starterUK · Jan 30, 2011#9 Originally Posted by
cali yaris ↑ ^ this depends on the offset of the wheel and the tire being used, and also camber. A little negative camber goes a long way to eliminate rubbing (and improves handling too!).
It may be necessary to trim some fender liner away in spots to eliminate any rubbing.
Ok thanks for your advise, but as a set up 10mm at the front and 13mm at the rear is this a good starting point?
the wheels are 215/45/r17 not sure what the offset is
Thanks
WeeYariGeorgetown, Ontario, Canada · Jan 30, 2011#10Not withstanding the critical offset number, here is one thing to keep in mind.
Installing 10 to 13mm spacers in the back will bring the rear wheels more inline with the fronts. Installing 10mm in the front will continue to push the wheels out further than the rear.
If you are looking for cosmetic symmetry front to rear, then I would not put anything on the front. What is your ultimate goal?
NipsThread starterUK · Jan 30, 2011#11 Originally Posted by
WeeYari ↑ Not withstanding the critical offset number, here is one thing to keep in mind.
Installing 10 to 13mm spacers in the back will bring the rear wheels more inline with the fronts. Installing 10mm in the front will continue to push the wheels out further than the rear.
If you are looking for cosmetic symmetry front to rear, then I would not put anything on the front. What is your ultimate goal?
Main goal is for the rear to fill out the arch and better handling, i intend to add strut braces in the future but have no plans to lower the car at this point because i want to keep the ride comfortable.
Lowered every previous car i have owned and don't want a back breaking ride, plus UK roads are shit compared with US roads from what i've seen
NipsThread starterUK · Jan 30, 2011#12How would i find/work out the offset?
cali yarisCanoga Park, CA · Jan 30, 2011#13^ you can either look up the wheel online, or it might be cast into the back of the wheel.
Or you can post a few pics of what it looks like now, so we can all comment, discuss, and nitpick the whole thing -- which is great for you. 😆
NipsThread starterUK · Jan 30, 2011#14 Originally Posted by
cali yaris ↑ ^ you can either look up the wheel online, or it might be cast into the back of the wheel.
Or you can post a few pics of what it looks like now, so we can all comment, discuss, and nitpick the whole thing -- which is great for you. 😆
Hopefully this will help
Picture not included in this copy AltitudeColorado · Jan 30, 2011#15I've got 215/35/18 with a 42(or maybe 45) offset and I installed the 10mm Penguin spacers on the rear. No spacers on the front. Looks great!
NipsThread starterUK · Jan 31, 2011#16 Originally Posted by
Altitude ↑ I've got 215/35/18 with a 42(or maybe 45) offset and I installed the 10mm Penguin spacers on the rear. No spacers on the front. Looks great!
Got any pics?
Just awaiting a reply from micro image, i think i will order 13mm peguins for the rear and leave the front standard
matthewaiunited states · Feb 5, 2011#17yeah do you have pics altitude i was thinking about this mod as well
ArmyYarisFort Campbell, KY · Oct 12, 2011#18What spacers would you reccomed for the stock 15's?