PARISOriginal postATHENS KALLITHEA · Jan 22, 2011#1Hi guys! is there anyone that knows whats the max horsepower you can push reliably on the 1nzfe stock sleeves?
has anyone cracked a sleeve?
Replies 12
😲 you kidding right? Use the search function guy.
xbgodFlorida · Jan 22, 2011#3I don't think you need to worry about it.
Unless your gonna do something like me , Cali, Blown Xa, or someone in our arena.
But unless your gonna get over like 280hp you don't need to deal with it.
XBG
ParmasML · Jan 22, 2011#4I am using stock sleeves and I hope for 14 psi they will hold well
PARISThread starterATHENS KALLITHEA · Jan 22, 2011#5But i think you had dynoed it at 16 psi 250 bhp parmas?
cali yarisCanoga Park, CA · Jan 22, 2011#6^ best answer you're going to get.
ParmasML · Jan 23, 2011#7 Originally Posted by
PARIS ↑ But i think you had dynoed it at 16 psi 250 bhp parmas?
That was a long time ago with the previous management but that was only on the dyno. We decided to go 9psi until we solved the tuning issues. The problem was infact the ecu that do not match with the yaris engine and now I changed to Haltech management.
Due to new management I had to re-tune the engine and till now I am still 9psi. I never run a daily 16psi so I don't know if it will hold eventually for long time but I am thinking of uppping the boost slowly keeping an eye on the temp, pressure and AFR gauges.
PARISThread starterATHENS KALLITHEA · Jan 23, 2011#8Aren't honda engines from exactly the same material as ours? both are all aluminum and open deck i think?
xbgodFlorida · Jan 23, 2011#9The blocks are aluminum castings then machined.
cylinder block: aluminum with cast-in iron liners.
cylinder and crankshaft centers are offset to reduce piston slapping.
The combustion chambers in the scion engine employ a tapered (oblique) squish design, to improve thermal efficiency and reduce the chance of engine knock (pre-ignition). the squish area has been shaped obliquely along the wall surface of the combustion chamber, improving airflow, promoting swirl and speeding flame travel.
the combustion chambers are almost entirely machined, to ensure minimum variation in combustion chamber volume across the four cylinders. special attention has been paid to cooling the combustion chamber, including provision of a water jacket between the exhaust port and the spark plug boss, to lower the operating temperature at the exhaust valve seat and improve cooling performance.
XBG
Paris vvt-iAthens · Jan 24, 2011#10I think that blown_xa also was in stock sleeves pushing 247whp. Perhaps you could ask him!
schragenColorado · Jan 24, 2011#11^but probably has forged internals
Blown_xaVirginia · Jan 27, 2011#12Yea I wouldnt worry about sleeving, the factory sleeves are plenty strong. I have about 30,000 miles on my built motor now, it has been reliable and there is no signs of abnormal cylinder wear ( I do leakdown test every 6 months). If sleeving isnt done properly then you will encounter issues, it's not worth the risk in my opinion .
I build most of the motors at Ptuning , I can tell you the factory sleeves are the same thickness as the tc block from looking at the motors torn down. We have taken that block past 600hp.
ParmasML · Jan 28, 2011#13 Originally Posted by
Blown_xa ↑ Yea I wouldnt worry about sleeving, the factory sleeves are plenty strong. I have about 30,000 miles on my built motor now, it has been reliable and there is no signs of abnormal cylinder wear ( I do leakdown test every 6 months). If sleeving isnt done properly then you will encounter issues, it's not worth the risk in my opinion .
I build most of the motors at Ptuning , I can tell you the factory sleeves are the same thickness as the tc block from looking at the motors torn down. We have taken that block past 600hp.
That is a very good news for me
Cheers Mate!