Yarisworld Archive

Gude cams "NOT SO NACHO"

73 posts · 21,397 views · page 1 of 2

xbgodOriginal postFlorida · Dec 14, 2010#1
I'm here to report that we just ran into a issue with the compression of the motor, After installing the Gude head package. It appears to be a overlapping issue of the cams.

Rolo wanted to start the car on the Microtech and see how it responded while waiting on the Haltech. In doing so the car did not want to start, even though there was fuel, air and spark. So after scratching his head and tring to figure out WTF happened he did a compression check on the motor and it was at 55lb across the board. A engine needs a 100lb to start so we knew where the problem was instantly. The head was the only thing changed on this car for this new build.

Bottom end was same as before and ring seal was perfect.

I had 180lb across the board before the "Gude head and Cams"

As you can imagine I'm a little pissed about this but these are things to expect when dealing with something or someone new. "Gude"

Old race head will be back on by Sat. This is the one I've been using for a few years and have had zero issues with. So for all that were interested in it, sorry it's going back on my car.

I haven't called gude yet but I'm sure it will not be worth my time. These are racing parts and like all racing parts it's hard to recupe money on these kinds of parts.

for all those that this is working good on, keep any eye on the valve bucket set-up. That valve-seat tit extender he uses to go under the bucket to get the clearence could become a issue with you daily drivers.

So as it stands right now Bill Gude needs to figure out WTF is going on with his shit. I do not belive any of this stuff was tested properly before it left his shop.

Buyer beware........

So here you guys go, this has been a lesson learned. Untill someone that is reputable makes a kit Like my good friend Brian Crower, stay away.

You can port and polish and install Ferrea valve train just don't do any cam stuff untill a real company can give some hard evidence.

XBG

Replies 72

hatchbackkid82. · Dec 14, 2010#2
XBG HAS SPOKEN!!!!! 👍
xbgodThread starterFlorida · Dec 14, 2010#3
I'll never give false info when it comes to parts or performance. If it sucks I'll tell you. And if my tunner syas it sucks, belive me........it sucks.

I'll never put out false numbers or performance gains on parts that are just not worth a shit.

This is one time being a gunie-pig did not pay.

Just got texted the Gude head is off my car!

Time to regroup and get it going again.

XBG
H3LlIoNMidatlantic · Dec 14, 2010#4
My Gude stuff works great. Question...did you give him specs and ask him to build it, or did he come up with the profile on his own and make it for you?

Call Bill, he's been pretty amicable on the phone as of late. He was more than happy to help out with the minor problems we had upon install.

And if you end up trashing that stuff, PM me before you throw it away.

On another note, I think we're declaring the gude stuff officially "hit or miss" at this point.
xbgodThread starterFlorida · Dec 14, 2010#5
I would say more of a miss. even you had to fabricate some stuff to get the cam gear correct.

I don't belive you should have to refabricate someone elses work when it should work already. Especially this kind of stuff. If it was battery bracket or a catch can, ok I can refab that to fit how I want it.

And after I gave him all my numbers on my motor down to every last detail he figured out what I should need. So these cams were done on his recomendations as per my turbo, compression and so fourth.

I'm not bitter nor will I say he is a total loss of a cam engineer. However I do not think he has the equiptment to pull off a true tested set of cams for this motor. Unlike Jun Performance who has a set-up to test all their cam configureations.

I think Gude has copied alot of cams from other cam company profiles and sells them as his own. Which is why he sells alot of Honda stuff. I think he just got creative and seen he could make a buck on a new product that no one else is doing.

Also after talking with Brian Crower there are reasons that no one is doing these cam profiles for this engine. If the demand was great enough like a 100 or more he would consider doing them. But it will take much more than a new set of cams for this motor. Were talking springs, buckets and possibly new valves instead of those tits Gude puts in a bag to go on top of the valve to fit in the bucket for clearence.

XBG
Jason@SportsCarDebary, FL · Dec 14, 2010#6
We had no issues with our cams from Rebello, other than giving up some Tq to make high RPM power. Granted we are using a much more mild setup than you guys, we are limited to .390 lift by SCCA H Prod rules, but it was an easy swap with no crazy machine work or custom cam-gears needed. 🤷
Focus_Sh1ftNew Jersey · Dec 14, 2010#7
Damn bro, sorry to hear about that. That's aggravating to pay so much for something that isn't even in the correct spec 😠

I'm super bummed about the head as well. If it comes off again, let me know the moment it does. I'll always have some money put aside for that goodie 😁
ParmasML · Dec 15, 2010#8
Please for the sake of all, do a leak down test before you remove the head in order to be sure that the head is the problem.

Also did you replaced the head gasket or re-used the one you had? What head gasket are you using? This could be one of the causes.

Last thing, From my experience, NEVER say it's not my tuner, because like all people, they make mistakes but they do not admit them to prevent bad publicity.

BE SURE YOURSELF IS THE HEAD AND NOT BECAUSE YOUR TUNER SAID SO. DO A LEAKDOWN YOURSELF IF NECESSARY, if when doing the test the air does not leak from the intake nor exhaust ask the tuner if he replaced the headgasket upon install.
xbgodThread starterFlorida · Dec 15, 2010#9
Leakdown was performed. And come-on..really, do you think i'd use a used head gasket.

New steel head gasket from Cometic and new head studs.

wish I had a different answer and didn't narrow it down to the head.

XBG
ParmasML · Dec 15, 2010#10
That's fine at least I pointed this out to ensure all possibility issues.

What cometic gasket are you using? Is it a custom one or does cometic stock gaskets for our 1NZFE?

What studs did you used on your built?
xbgodThread starterFlorida · Dec 15, 2010#11
Just talked to Bill "Gude" Told him of the issues and right away he went to saying the timming was off and I must of bent valves and thats why the compression is low.

But wait, theres more....................

I then asked him to explain the excessive amount of metal shavings that were found TODAY after inspecting the motor. And since the only thing I did different was put on his head with a bottom end I've been using for the last year I knew it wasn't from there.

But wait there is still more................

Told him the motor never even fired because of lack of compression 55lb across the board and that after even further inspection today all the valves were sticking and not closing.

I went from 180lb across the board to 55lb with the chage of his head. Right now he is speachless and wants me to send the head back to him to inspect and fix.

Still more...............a excessive amount of carbon was also found on the valves because, you know Gude uses stuff from the junk yard to build his heads with.

Would not comment on who actually did the cam regrinds or who in his shop did the head work and assembly.

Here is what you get from Gude head package:

First head comes from junk yard. He then disassembles it cleans it and sends all that used shit out to someone for someone else to redue.

Cams are not ground in-house (will not say who actually did it)

Head work is done in-house by some retard and not him.

Everything about his head package is used shit from the salvage yard, except for the springs. Which he says Eibach makes for him. I'm about to find out if that is even true. Since I got a friend that does all the sponsorship over there.

So what you get gentlemen is a used head with used valves and used cams that get reground and installed with new springs (mabey)

And all that red shit he uses to check for valve fitment causes the valves to stick and not open or close properly.

All these issues were found out today upon further inspection and more investigation.

Bill you fucking Rock 🤘

Like I want all used recleaned shit from a junk yard in a 20k motor.

I'm just going to get all the pictures from CFT and post all this stuff online to ruine him so others avoid The junk Yard Dog.

XBG
Jason@SportsCarDebary, FL · Dec 15, 2010#12
Originally Posted by xbgod ↑
Just talked to Bill "Gude" Told him of the issues and right away he went to saying the timming was off and I must of bent valves and thats why the compression is low.

But wait, theres more....................

I then asked him to explain the excessive amount of metal shavings that were found TODAY after inspecting the motor. And since the only thing I did different was put on his head with a bottom end I've been using for the last year I knew it wasn't from there.

But wait there is still more................

Told him the motor never even fired because of lack of compression 55lb across the board and that after even further inspection today all the valves were sticking and not closing.

I went from 180lb across the board to 55lb with the chage of his head. Right now he is speachless and wants me to send the head back to him to inspect and fix.

Still more...............a excessive amount of carbon was also found on the valves because, you know Gude uses stuff from the junk yard to build his heads with.

Would not comment on who actually did the cam regrinds or who in his shop did the head work and assembly.

Here is what you get from Gude head package:

First head comes from junk yard. He then disassembles it cleans it and sends all that used shit out to someone for someone else to redue.

Cams are not ground in-house (will not say who actually did it)

Head work is done in-house by some retard and not him.

Everything about his head package is used shit from the salvage yard, except for the springs. Which he says Eibach makes for him. I'm about to find out if that is even true. Since I got a friend that does all the sponsorship over there.

So what you get gentlemen is a used head with used valves and used cams that get reground and installed with new springs (mabey)

And all that red shit he uses to check for valve fitment causes the valves to stick and not open or close properly.

All these issues were found out today upon further inspection and more investigation.

Bill you fucking Rock 🤘

Like I want all used recleaned shit from a junk yard in a 20k motor.

I'm just going to get all the pictures from CFT and post all this stuff online to ruine him so others avoid The junk Yard Dog.

XBG
That sucks. 😠
xbgodThread starterFlorida · Dec 15, 2010#13
Going to use my Nelson Racing Head that I had done a few years ago which was ported and polished and ran with Ferrea Valves that are +1mm oversized which worked great and produced good results.

So here's where we are:

Nelson Racing Head Ported ,Polished
Ferrea Valves+ 1mm oversized, springs, lockers and retainers
Cometic Steel gasket
Stock Cams

Just had all my stuff cleaned reassembled and assembly-lubed

not to mention had the rest of the motor inspected blown-out and dumped out 50.00 in Eneos oil and 15 K&N oil filter.

All should be back together by the weekend and ready to refire by early next week.

Gude Performance = Lesson learned

XBG
ParmasML · Dec 16, 2010#14
That's what I call business .....
ilikericesavannah, ga · Dec 16, 2010#15
i want to say thank you xbgod. for taking the time and money to try a new head that us low ballers cannot afford to risk. thank you for your posts and your storys. i have been watching all the threads on gude heads since sept. and been waiting patiently for some results. aparently H3lton has had good luck with his.. but yours is a miss.. if its down to a hit or miss 2k head, i dont think the risk is worth it. again. thanks you and hope the rest of your build is a success
Midnight DrifterMonroe, NJ · Dec 16, 2010#16
Helion, not Helton... :D

But yeah, that sucks. XBGod, for reference, is your 'old' (new?) head custom?
xbgodThread starterFlorida · Dec 16, 2010#17
Not even H3lion had real success out of the box. He also had to have a timming gear refabricated to get his set up correct.

Which for over a thousand plus dollars you shouldn't need to do. So in reality there has been no out of the box success.

You guys with no machine-shop access or online shop mechanical guides to use like the repair shops have are left holding the bag and fucked.

Which as a fabricator of racing parts, I think is bullshit. If I sent racing brakes out to customers that didn't work, had to be refabricated or caused other parts to fail..........the company I worked for would be broke from getting sued or out of business.

I gave Bill Gude all the leway in the world with his business practices. Even as far to say "there a family owned business and not always so easy to get with." because of lack of employes.

Well thats no longer an excuese. You have no real employes because any one with half a brain would run the other direction if they had to fix all your problems.

So as it stands there has been no real success with Gude performance other than me getting the info out to you guys and flushing a couple grand down the toilet.

XBG
hatchbackkid82. · Dec 16, 2010#18
How is Gude still in business!? 😲
xbgodThread starterFlorida · Dec 16, 2010#19
That plus......................

He knows all the right things to say and answer.

It's like the saying "Those that cant do...."Teach"

Belive me I'm coming up with a way to break it off in his ass.

XBG
Nexus1155Dorchester · Dec 16, 2010#20
I feel bad this happened to you, reading in the past and in the back of my mind i thought something would go screwy. I thought you would have better luck than the rest since you have a boosted motor. Seeing all the people on scionlife and the reviews about gude, it seems like the cost was not worth the power or flow given as the 1nz is pretty optimized already?

You can't expect to get a new head and him to do that work for that price though, that much is obvious. A head is a head, mill the surface and I'll use it all day. Even gunked up engines that I have used have lasted over 50k miles with no issues. Your engine won't be clean forever anyways.

I hope he does something to help you out in terms of $$$ or fixing the head for you free of cost and you can either use or sell it. If he does, then props to him, if not then thats just bad business. But damn man, shavings in the engine.... WTF????
Jason@SportsCarDebary, FL · Dec 16, 2010#21
Originally Posted by cdydjded ↑
Cause there is a sucker born every minute...
There is always plausible deniability... He did not build the entire engine, so he can always pass the blame when questioned, and most people will believe him because it seems like a plausible excuse.

Even our guy tried to blame our tuner for the loss of Tq. When it seems clearly evident, even with the small sampling of modded 1NZE's, that the loss of Tq is a side effect of a cam change that makes high RPM power.

If you don't know the answer, just say you don't know, don't lie or pass the buck.
xbgodThread starterFlorida · Dec 16, 2010#22
funny how people do that.

I didn't even get a word edge-wise with Bill Gude when I told him of the issue. He instantly went to your engine builder did the timming wrong and bent your valves.

Finally he shut -up and I explained to him I been using the same engine builder and Prior to changing the head I had 180lb across the board. I put his Junk Yard Dynamics on and like a Fairy waving her wand.....Boomb goes the Dynamite.......55lb across the board along with shavings in my motor.

He didn't once even say, Shit sorry to hear what happened or I'll send a call tag to bring it back and look at, to get to the bottom of this. God forbid he take responsability for his product and inspect it.

I wouldn't run his shit if it came wraped in 100 dollar bills.

no matter what he does it will remain a boat anchor in my shop for all to see and I will continue to fuck this guy down every chance I get.

XBG
Blown_xaVirginia · Dec 16, 2010#23
sorry about your misfortune. I have heard so many stories of shadyness in the performance industry, it is sad. I am a firm believer in testing products before they are sold.

Reminds me of an evo I worked on... guy drove from 5 hours away for us to check out a few issues and then tune his car. As soon as i pulled the car in i heard an odd noise from the motor. I then raised the car on the lift while it was running and as i did so the oil pump pulley shot through the timing cover and the timing belt skipped, motor locked.
I then showed the customer, he told me the motor was just built by another shop... needless to say he was upset. he then had me talk to the owner of that shop, very defensive and swore it wasnt their doing and that the pulley couldnt have come off as it comes preassembled on oem oil pump . I ordered new pump, and not to my suprise.....pulley is seperate, you can't even install it with the pulley on anyhow. They either didnt put the nut on, or never torqued it.
shadyness
hatchbackkid82. · Dec 17, 2010#24
Anyone know if his rap is this bad witht the Honda guys?
xbgodThread starterFlorida · Dec 17, 2010#25
Even worse with them.

Just Google something like, Gude performance sucks for Honda.

And watch all the other forum posts pop up. It's like magic

XBG
hatchbackkid82. · Dec 17, 2010#26
That's crazy cause i remember Gude being around as early as 2003, and he's been doing this to people for this long. It's only a matter of time before he goes the ZPI route
scioncrewHB · Dec 17, 2010#27
he has been around long. i use to have one of his heads on my 95 Eclipes back then.
fnkngrvIn The Hotbox · Dec 19, 2010#28
just a shit end of the stick all the way around
xbgodThread starterFlorida · Jan 1, 2011#29
Selling the Gude head package I was going to use. Couldn't get the cams to work correctly. Maby you can.

Kit comes with:

Completely ported, polished head
Valves, springs, lockers, seats, retainers all assembled
Race cams

and Big bore T/B

will sell for 450.00 plus freight.

no seperation of parts. head alone is worth 900.00 by it self.

PM me

XBG
ilikericesavannah, ga · Jan 1, 2011#30
is it possible to use stock cams, or stock cames that grinded elsewhere on this head? or is specificly cams for that particular head?
xbgodThread starterFlorida · Jan 1, 2011#31
yes, just remove Gude cams and springs and install your stock stuff into the ported head.
ilikericesavannah, ga · Jan 2, 2011#32
hells yea.. thats one hell of a deal then.. if i wasnt about to buy new rear tails and also saving up for a LSD and a roll bar, your head (if not sold) is next on my list
TamagoOff Grid · Jan 2, 2011#33
built, not bought (from gude or your tuner) sounds like a much safer solution to your problems.. but you'd have to get your hands actually dirty then...
xbgodThread starterFlorida · Jan 2, 2011#34
Well I say if you got the money, fuck it, let someone else do the work. especially if they got all the tools and you don't have to buy them to do the job.

XBG
TamagoOff Grid · Jan 2, 2011#35
Originally Posted by xbgod ↑
Well I say if you got the money, fuck it, let someone else do the work. especially if they got all the tools and you don't have to buy them to do the job.

XBG
so then why are you even complaining? if you knew how to actually do the work, but paid others to do it, then you deserve whatever they do to you.
xbgodThread starterFlorida · Jan 2, 2011#36
not like I keep a cam grinder on hand you fuck-tard. Doing work and machining work to different things.
TamagoOff Grid · Jan 2, 2011#37
Originally Posted by xbgod ↑
not like I keep a cam grinder on hand you fuck-tard. Doing work and machining work to different things.
you bought an assembled head. this means that: A: your 'tunner' doesn't know how to assemble a head, so you paid this Gude guy to do it for you, or B: you are lying to us about the specs you gave to Gude for your cams, because you've relied on "internet intelligence" to choose the numbers for your lift/duration on your cams.. it sounds like your "tunner" didn't do his job, and you're bouncing back to the yarisworld innanetz to complain.

yarisworld, disregard this assclown... he's spending money, but has no idea why... sad that he spent this much on a 1nz when a little bit of actual innovation would have yielded him over 500whp on the same car (with a 1zz) and a bit of actual innovation.
xbgodThread starterFlorida · Jan 2, 2011#38
The tuner is not responable for building the head. He Tunes you retard!!!!

And the specs were not correct on the cams way too much over lap.

And I now know Gude dosen't even grind the cams himself, he sends them out. And apparently dosen't inspect or check them before sending them out.

You got a answer for everthing don't you. Take your gay MR2 and go to the forum that supports you.

XBG
xnamerxxso cal · Jan 7, 2011#39
Originally Posted by xbgod ↑
The tuner is not responable for building the head. He Tunes you retard!!!!

And the specs were not correct on the cams way too much over lap.


XBG

Um dont mean to be a dick but this is a dohc engine with vvti thats all in the setting of the valve timing this isnt a cam for sohc or pushrod engine where the overlap is speced into the grind of the cam. What is the information on the camcard you were given?
rob323Joyner, Brisbane · Jan 25, 2011#40
Are the valves bent and is that what is causing them to stick?
xbgodThread starterFlorida · Jan 25, 2011#41
Well Gude dosen't give a cam card it's a crap shoot with this retard.

And to answer your question, I haven't even had the time to go back and inspect Gudes crap yet. This weekend I may get a chance to look at it. But fisrt and fore most had to stop a couple of small collant leaks and I had the wastegate made to go to atmosphere now.

XBG
xnamerxxso cal · Jan 25, 2011#42
Originally Posted by xbgod ↑

And the specs were not correct on the cams way too much over lap.



XBG

Originally Posted by xbgod ↑
Well Gude dosen't give a cam card it's a crap shoot with this retard.

XBG
How could you possibly know if it had to much overlap if you didn't get a cam card.
xbgodThread starterFlorida · Jan 25, 2011#43
From the engine builder and the tunner comparing the cams and doing the math.

And before you proceed any furether with this, do your self a favor and don't take this down a road your not willing to go down. I know you get what I'm saying.

XBG
rob323Joyner, Brisbane · Jan 25, 2011#44
Originally Posted by rob323 ↑
Are the valves bent and is that what is causing them to stick?
Do you know of this is the case yet?
xbgodThread starterFlorida · Jan 25, 2011#45
no not yet. The head hasn't been pulled apart enough for examination. At the time it was get the old one back and on to do dyno pulls and get the car running. I'm pursuing this whole head thing and coming up with something reliable and just plain bad ass. It won't be for those not willing to drop some coin but I'm hoping to solve some issues with great resolve with amazing results. Looking at even machining some Titanium cam gears just for G.P.

XBG
xnamerxxso cal · Jan 25, 2011#46
Originally Posted by xbgod ↑
From the engine builder and the tunner comparing the cams and doing the math.

And before you proceed any furether with this, do your self a favor and don't take this down a road your not willing to go down. I know you get what I'm saying.

XBG
Really so your "tunner" (spelled tuner btw) compared the cams and did the "math". What math did he do just curious?
The stock engine overlap goes from -2 - 12 degrees of overlap so tell me how does comparing old cams to new ones tell if it has more overlap? The overlap can easily be changed from modifying the vvti settings.
So basically what your saying is someone told you it had to much overlap and you agreed.


Btw making threats on the internet is the behavior of a child.
xbgodThread starterFlorida · Jan 26, 2011#47
No, it's ass-holes like you that need to know everything and need to continue to poke at something.

So untill you can get that Yaris of yours to beat my numbers, you don't need to worry about me.

I'm doing things no one else is even doing. I don't even run vvti. I use an external crank trigger like a regular drag car.

So why don't you take you and your 29 post and go chime in on someone who gives a shit. Your a little late to ring in on my thread.

It was obvious from your previous post you were looking to start something. Just because you cant get your jelly bean to pull off what I did, don't go looking for reasons to hate and make your own ajenda of my success.

Sorry you suck at life.

XBG
hatchbackkid82. · Jan 26, 2011#48
😲
ShinareOklahoma City, OK · Jan 26, 2011#49
Originally Posted by xbgod ↑
... Just because you cant get your jelly bean to pull off what I did...
Hey now, nothing wrong with jellybeans.... heh 😉
thebarberGrand Rapids, MI · Jan 26, 2011#50
Picture not included in this copy