Judas IscariotOriginal postMount Royal, NJ · Dec 6, 2010#1Hello members, i have tried every search i can think of and nothing is helping.
a few days ago my headlights stopped working. i know this because i was driving at night and all was well, i remember using my highbeams on a particular road. anyway the next morning (i leave for work around 6:15) i started the car aND put my foglights on (i did the foglight w\ parking lights mod AND disabled DRL's) and when i was geting ready to pul out flicked on D\L and nothing.
Checked all fuses i could find and the bulbs are not burned out. Any help would be appreciated, before i take it to toyota.
Replies 66
CTScottUSA, CT · Dec 6, 2010#2Check the bulbs first. It's not that likely that they both failed, but is worth a look.
Check the two H-LP fuses in the under hood fuse panel.
Check the ECU-IG fuse in the under dash fuse panel.
Judas IscariotThread starterMount Royal, NJ · Dec 6, 2010#3Thx for replying. Will check tomorrow at lunch time.
Judas IscariotThread starterMount Royal, NJ · Dec 7, 2010#4ok i checked and it was one of the fuses under the hood. unfortunantly when i replaced it, the fuse blew again... 👎
i think the next step is to rewire things to stock (Looks like someone was messing around underthere that wasn't me!) and se what happens
any suggestions are welcome THX again
CTScottUSA, CT · Dec 7, 2010#5 Originally Posted by
Judas Iscariot ↑ ok i checked and it was one of the fuses under the hood. unfortunantly when i replaced it, the fuse blew again... 👎
i think the next step is to rewire things to stock (Looks like someone was messing around underthere that wasn't me!) and se what happens
any suggestions are welcome THX again
Which one was popped? From there I can guide you as to which wires to follow.
Judas IscariotThread starterMount Royal, NJ · Dec 7, 2010#6The extremely difficult one to remove and put away. . Lol. If your standing in front of the car facing towards the rear, the left of the two you said to check.
CTScottUSA, CT · Dec 7, 2010#7That's the fuse for the right hand side (sitting in the car) headlight. The fuse feeds the black wire on the headlight directly, and then the green and blue wires are the switched grounds for high and low beam. Since you are popping the fuse, the short has to be between the fuse and the bulb.
Betriventedmonton · Dec 7, 2010#8 Originally Posted by
CTScott ↑ Check the bulbs first. It's not that likely that they both failed, but is worth a look.
Check the two H-LP fuses in the under hood fuse panel.
Check the ECU-IG fuse in the under dash fuse panel.
I can't stress this part enough.
Oh nuts you already checked. Would a beefier fuse solve this problem? CT? I'm genuinely curious
CTScottUSA, CT · Dec 8, 2010#9 Originally Posted by
Betrivent ↑ Would a beefier fuse solve this problem? CT? I'm genuinely curious
NOOOOOOOO! Putting in a bigger fuse generally results in doing far more damage. Wires have a current rating and the fuse value chosen for a circuit generally is a function of the ampacity of the wiring and the maximum current draw of the device(s) on that circuit. Installing a larger fuse often results in exceeding the ampacity of the wiring, and if there is a direct short in the circuit, the now underrated wires will get extremely hot, possibly hot enough to melt their insulation and burn other things (or create more shorting points).
Judas IscariotThread starterMount Royal, NJ · Dec 8, 2010#10Agreed, i wouldn't think of using a larger fuse... and i did check to see if the bulbs are good, i can see both hi\low filaments, they are intact and the bulbs were less than a week old at time of origional post.
Thanks for the replys CT, but you were saying something about which wires to follow... if pictures will help i can have them on here tomorrow.
CTScottUSA, CT · Dec 8, 2010#11 Originally Posted by
Judas Iscariot ↑ Agreed, i wouldn't think of using a larger fuse... and i did check to see if the bulbs are good, i can see both hi\low filaments, they are intact and the bulbs were less than a week old at time of origional post.
Thanks for the replys CT, but you were saying something about which wires to follow... if pictures will help i can have them on here tomorrow.
Pictures would definitely help. The wiring harness to the right side headlight is housed in wire loom for all but a few inches on either end, so if the problem is with the OEM wiring it is almost definitely on one end or the other of the wire from the fuse panel to the bulb. The additional wiring, that you mentioned, is more likely where the problem lies, so pictures of that would help.
Judas IscariotThread starterMount Royal, NJ · Dec 9, 2010#12Thx CT, i left my camera at home, so i'll take the pictures tonight and hopefully post them tomorrow.... i hate not having headlights!
Judas IscariotThread starterMount Royal, NJ · Dec 24, 2010#13Ok. So I am still battling this problem. The headlights come on now. But the driver side light is acting funny, both of the filaments are coming on and they are dim in comparison to the other one. Which works correctly. I don't know how it got to the state it's inn now. But at least I can drive at night. Any more ideas CT? Thanks again in advance
CTScottUSA, CT · Dec 24, 2010#14 Originally Posted by
Judas Iscariot ↑ Ok. So I am still battling this problem. The headlights come on now. But the driver side light is acting funny, both of the filaments are coming on and they are dim in comparison to the other one. Which works correctly. I don't know how it got to the state it's inn now. But at least I can drive at night. Any more ideas CT? Thanks again in advance
The H-LP/AMT Relay in the small relay box, on the passenger side, under the hood, may be sticking. You can try putting the HTR relay in its place to see if it cures the problem. The HTR relay is the center one at the bottom of the under dash fuse panel. The HTR relay is the same shape as the H-LP/AMT relay, but may have a different color shell. The two are identical though in function, so they can be swapped.
Judas IscariotThread starterMount Royal, NJ · Dec 28, 2010#15Thank you CT. unfortunatly that didn't fix it. And it's the left relay under the dash, because the middle one has five prongs while the other two have four. You are still very helpful. And I wish that fixed it, boo. I was so excited for that to work. What's next? (sigh)
AltitudeColorado · Dec 28, 2010#16 Originally Posted by
Judas Iscariot ↑ What's next? (sigh)
Make your peace with Jesus?
(sorry couldn't resist)
Judas IscariotThread starterMount Royal, NJ · Dec 28, 2010#17Haha. 😆
Judas IscariotThread starterMount Royal, NJ · Dec 28, 2010#18Oh. And now my heater won't work. Grrrrrr
CTScottUSA, CT · Dec 28, 2010#19Do you by any chance have (and know how to use) a multimeter?
Judas IscariotThread starterMount Royal, NJ · Dec 28, 2010#20Lol. Yeah. Got one at work. And I know how to use it. Funny thing is, who owns one and can't use it. Just joking around. I'm curious to know how YOU know all this stuff tho. Your knowledge base is incredible.
CTScottUSA, CT · Dec 28, 2010#21 Originally Posted by
Judas Iscariot ↑ Lol. Yeah. Got one at work. And I know how to use it. Funny thing is, who owns one and can't use it. Just joking around. I'm curious to know how YOU know all this stuff tho. Your knowledge base is incredible.
You'd be amazed as to how many people have one laying around, but have no clue as to what to do with it. I'm a EE with 20 years experience in robotics and medical automation.
Judas IscariotThread starterMount Royal, NJ · Dec 28, 2010#22 Originally Posted by
CTScott ↑ I'm a EE with 20 years experience in robotics and medical automation.
That explains the yaris snow plow. Haha
Judas IscariotThread starterMount Royal, NJ · Dec 29, 2010#23Heater is ok. False alarm. I didn't put the relay in all the way. But about that multimeter....
CTScottUSA, CT · Dec 29, 2010#24 Originally Posted by
Judas Iscariot ↑ Heater is ok. False alarm. I didn't put the relay in all the way. But about that multimeter....
Here's where to start:
In the picture below (of the headlight stalk connector) measure the voltage on the sky blue wire (next to the pink wire) with respect to either of the white wires with the black stripe.
Headlights off:
Headlights on (low beam):
Headlights on (high beam):

Judas IscariotThread starterMount Royal, NJ · Dec 29, 2010#25voltage numbers
off- 13.8
on- 13.7
hi- .04
that last one seems funny to me, but i'm no pro.
CTScottUSA, CT · Dec 29, 2010#26 Originally Posted by
Judas Iscariot ↑ voltage numbers
off- 13.8
on- 13.7
hi- .04
that last one seems funny to me, but i'm no pro.
That's fine, now same with the pink wire.
Judas IscariotThread starterMount Royal, NJ · Dec 29, 2010#27uh i did the pink wire first... oops, but i went out and did the sky blue one just now
off- 12.6
on- 0, yes zero
hi- 3.4
???? oh man🤷
CTScottUSA, CT · Dec 29, 2010#28OK - The off- 13.8, on- 13.7, hi- .04 makes sense for the pink, which is the high beam wire.
The off- 12.6, on- 0, hi- 3.4 is OK for the light blue, which is the low beam.
So, the headlight stalk is working correctly. Next, measure the resistance between terminals 3 and 5 of the H-LP AMT relay (they are the two larger perpendicular to each other terminals).
Also, with the H-LP relay out, measure the voltage between the pin 5 position (the large blade that is perpendicular to the other 3) and ground.
Judas IscariotThread starterMount Royal, NJ · Dec 29, 2010#29Ok. There is no voltage between 3 and 5 on the relay itself. But I am getting 12.88 on the housing ( where the relay plugs into) on 3 and 5. And on 5 and ground 12.88 again
CTScottUSA, CT · Dec 29, 2010#30 Originally Posted by
Judas Iscariot ↑ Ok. There is no voltage between 3 and 5 on the relay itself. But I am getting 12.88 on the housing ( where the relay plugs into) on 3 and 5. And on 5 and ground 12.88 again
On the relay, measure resistance, rather than voltage between those two pins.
Judas IscariotThread starterMount Royal, NJ · Dec 29, 2010#31ah duh.... resistance is null, nothing at all
Judas IscariotThread starterMount Royal, NJ · Dec 29, 2010#32but if its a relay, shouldnt there be no resistance until 12v is applied to the little prongs?
CTScottUSA, CT · Dec 29, 2010#33 Originally Posted by
Judas Iscariot ↑ ah duh.... resistance is null, nothing at all
OK that's good. Now, voltage on each of the three headlight wires (on one side is fine)
CTScottUSA, CT · Dec 29, 2010#34 Originally Posted by
Judas Iscariot ↑ but if its a relay, shouldnt there be no resistance until 12v is applied to the little prongs?
It's a normally open relay, so the resistance is infinite (displayed as OL, null, etc.) Then when the relay is powered, it goes to zero.
Judas IscariotThread starterMount Royal, NJ · Dec 29, 2010#35 Originally Posted by
CTScott ↑ OK that's good. Now, voltage on each of the three headlight wires (on one side is fine)
doing now
Judas IscariotThread starterMount Royal, NJ · Dec 29, 2010#36brown and green wire on driver side 12.88
white wire nothing... i am testing each wire to a ground right?
CTScottUSA, CT · Dec 29, 2010#37 Originally Posted by
Judas Iscariot ↑ brown and green wire on driver side 12.88
white wire nothing... i am testing each wire to a ground right?
Yes. Also measure each with the headlights on and with high beam.
Judas IscariotThread starterMount Royal, NJ · Dec 29, 2010#38i know you said one side will do but i tested the pasenger side too and the only one that reads it the black one, again 12.88
Judas IscariotThread starterMount Royal, NJ · Dec 29, 2010#39going to test on and hi-beam now
Judas IscariotThread starterMount Royal, NJ · Dec 29, 2010#40ok the picture is the wires and locations
Driver Side
----- White green Brown
off - 14 -- 14 -- 14
low 5 -- .4 -- 9
hi -- 4 -- 9 -- .5
Pass Side
----- Black Blue Brown
off - 14 -- 12 -- 12
low - 14 -- .3 - .3
hi -- 14 -- 8.77 -- .67
hoipe the chart is useful, Thanks for helping. i can't say that enough CT
Judas IscariotThread starterMount Royal, NJ · Dec 29, 2010#41I forgot o load the picture. Sorry 🙄
CTScottUSA, CT · Dec 29, 2010#42No problem. Try pulling just the passenger bulb and then turning on the headlights to see what the driver's side bulb does in the three states with the other removed.
Judas IscariotThread starterMount Royal, NJ · Dec 30, 2010#43gonna do that on my lunch break...
here is the picture
Judas IscariotThread starterMount Royal, NJ · Dec 30, 2010#44these are the numbers taken with the opposite side detached. sorry it took all day.
Driver Side
----- White green Brown
off - 11.2 -- 11.2 -- 11.2
low .22 -- .22 -- .22
hi -- .02 -- .02 -- .02
Pass Side
----- Black Blue Brown
off - 13.8 -- 13.8 -- 13.8
low - 13.7 -- 13.7 - 13.7
hi -- 13.4 -- 13.3 -- .47
Judas IscariotThread starterMount Royal, NJ · Dec 30, 2010#45oh and the white wire is actually grey
CTScottUSA, CT · Dec 30, 2010#46Hmmmmmm. I am still reallllly thinking that the H-LP/AMT Relay might be the culprit.
With the bulbs both in, the charts should look like the following:
Driver Side
----- Grey Green Brown
off - 12 -- 12 -- 12
low 12 -- 12 -- .4
hi -- 12 -- .7 -- 12
Pass Side
----- Black Blue Brown
off - 12 -- 12 -- 12
low - 12 -- .4 - 12
hi -- 12 -- 12 -- .7
On yours, the low beam power is not being properly switched. On a working car, if you pull the relay, the high beams will work, but the low beams will not turn on at all (which is basically what you are seeing).
One last thing to try before replacing the relay is to unplug the DRL module's connector.
Judas IscariotThread starterMount Royal, NJ · Dec 30, 2010#47I disconnected the drl box and nothing. If Toyota is open tomorrow I will go get a relay. Or auto zOne. Some place like that hopefully has it
CTScottUSA, CT · Dec 30, 2010#48If you can find a way to jump the two large blade slots together, while the headlights are on, and on low beam, you can do a final check to make sure that that relay is truly bad (since it is a $30+ relay).
Judas IscariotThread starterMount Royal, NJ · Dec 30, 2010#49Wow. Sparks! Lol I'm ok. But the headlight stalk was in off position and when I connected the two the lights came on. That was suprising! But it didn't fix it. Every time I think it will work It doesnt. Oh well. What's next?
Judas IscariotThread starterMount Royal, NJ · Dec 30, 2010#50Another thing. I went put and pulled the relay. And the high beams do still come on, but the driver side lamp is still turning on both filaments. And they are still dim, really dim.