thebarberOriginal postGrand Rapids, MI · Nov 14, 2010#1got some time this afternoon while my daughter was napping in the car....finally put in one of the projector lenses in the oem yaris housing
went together relatively easy....
Picture not included in this copy
Picture not included in this copy
Replies 20
severous01SE Texas · Nov 14, 2010#2very nice. i'd thought about it but the cut-off line from the factory is very smooth and looks awesome even with halogens.
TylermayerSnohomish, WA · Nov 15, 2010#3where do you get the halo
thebarberThread starterGrand Rapids, MI · Nov 15, 2010#4 Originally Posted by
Tylermayer ↑ where do you get the halo
i sell them (and HID kits and LED's)...
yaris2010RSAngus, Ontario · Nov 16, 2010#5no now u can sell me mine and help with the install?
thebarberThread starterGrand Rapids, MI · Nov 16, 2010#6 Originally Posted by
yaris2010RS ↑ no now u can sell me mine and help with the install?
sure, sending PM now...
derickveliz2Central, MA · Nov 16, 2010#7Would you have a DIY? to share with Yaris World?
Kaotic LazagnaCentral Valley, CA · Nov 16, 2010#8Hey Adam, is that the bolt-on projector kit? If so, I think you may have installed it incorrectly. The cut-off is going to be vertical instead of horizontal. I'm thinking this because of where the LED's for the halo is located. They should be at the bottom of the ring, but in your picture, they are facing to the left of the headlight.
?????
thebarberThread starterGrand Rapids, MI · Nov 17, 2010#9 Originally Posted by
Kaotic Lazagna ↑ Hey Adam, is that the bolt-on projector kit? If so, I think you may have installed it incorrectly. The cut-off is going to be vertical instead of horizontal. I'm thinking this because of where the LED's for the halo is located. They should be at the bottom of the ring, but in your picture, they are facing to the left of the headlight.
?????
the bottom of the halo ring is pointing down
i actually installed them upside down to begin with just from taking the projector apart to look at it....
what i am doing to check the beam direction is shining an led flashlight i have thru the back of the lense....so its set up correctly, trust me.
you just have the orientation of the headlight wrong in your mind. the bottom of the headlight is the bottom left of the pic....
redglare45Pomona / Pasadena, California · Nov 17, 2010#10 Originally Posted by
derickveliz2 ↑ Would you have a DIY? to share with Yaris World?
Yes +1 on what Derick said.
How did you get them to sit "flush" towards the back of the housing? They look really good.
Kaotic LazagnaCentral Valley, CA · Nov 18, 2010#11My bad. lol, explained on MI. hahahaha. That angle just makes it look like a sedan headlight or a LB headlight laying on its side.
thebarberThread starterGrand Rapids, MI · Nov 18, 2010#12 Originally Posted by
Kaotic Lazagna ↑ My bad. lol, explained on MI. hahahaha. That angle just makes it look like a sedan headlight or a LB headlight laying on its side.
no worries
thebarberThread starterGrand Rapids, MI · Nov 21, 2010#13test fit the new projectors today
time to seal them up now....both work
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
mrrockct · Nov 22, 2010#14good job, are they a marked improvement over the stock light with better bulbs? how long did the whole job take you. do you sell and do the work.
only reason I ask is that I'm in St Clements several times a year
thebarberThread starterGrand Rapids, MI · Nov 22, 2010#15ok, got a second wind tonight after a pb&j, so i sealed the lights up.....went together much easier than i expected.....the lenses just popped back into the clips without issue....i really though i was going to have to bungee cord the backs and fronts together.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Betriventedmonton · Nov 23, 2010#16Nice. Did you have to dremel the inside of the housing for the projector to fit?
thebarberThread starterGrand Rapids, MI · Nov 23, 2010#17 Originally Posted by
Betrivent ↑ Nice. Did you have to dremel the inside of the housing for the projector to fit?
yes.
i had to cut off all of the brackets that normally hold the H4 bulb and bore out the hole a bit to fit the projector
47_MasoN_47Northwest Alabama · Nov 30, 2010#18Looks good, I'd like to get some projectors at some point but I'm afraid to commit lest I mess up something.
thebarberThread starterGrand Rapids, MI · Nov 30, 2010#19 Originally Posted by
47_MasoN_47 ↑ Looks good, I'd like to get some projectors at some point but I'm afraid to commit lest I mess up something.
its actually easier than i thought to convert the headlights...
that said, its nice to have an extra set of headlights
just in case i still have to actually wire them up and install them in the yaris, though.
47_MasoN_47Northwest Alabama · Nov 30, 2010#20Once you get yours done if it's not too hard to do the whole process (and if the price is right :D) I'll probably buy a set of those from you.
marcustoronto, canada · Mar 18, 2011#21barber ... need average time from opening and sealing per headlight.. and would hairdryer work to open the lights rather than baking it. maybe i can still get the projector lense from you been wanting it but scared to do the project,,,