Yarisworld Archive

Sound system upgrade

103 posts · 30,057 views · page 2 of 3

Replies continued

derickveliz2Central, MA · Jan 21, 2011#51
Originally Posted by packetrace ↑
😕So.....what do I need to do to make them sound better....
AMPLIFICATION! get a good amp.

Did you install the EQ-6500?

Are you running your speakers out of your deck?

D.
packetraceThread starterQuebec · Jan 21, 2011#52
I haven't insalled the eq6500 since i dont know where to mount it...and I dont have ampli for the speaker....they are actually wired to the stock wire...so...out of the deck...!


where had you mounted it ?

what kind of good amp should i buy....an amp that i could do a 3-way component like yours but later on!

thanks
_S7V7N_South Texas · Jan 21, 2011#53
I'm running 87 watts rms to my Hifonics components, and they sound okay, I'm fixin to add some cheap NB 1 tweeters to catch the high hats and some of the other higher frequency sound on the music, to help even out the hi's. Them lil cheap things are 97 db sensitivity so i can get away with just running them off the deck power. Check on Amazon for a 4 channel amp, i got mine for under 100 bucks, but i'm also going with an Okay brand, not top of the line stuff like Sqcomp and Derick. My amp is a Crunch 1400.4 I went with Maxxsonics amps. I also have a 1200 Brutus for the subs. Maxxsonics also makes Mb Quart, which is the top of the line brand for Maxxsonics. They also manufactured the Autotek brand as well. I want to go on ahead and just grab the 2000 watt brutus, but i don't think i can provide the power to feed that amp. Once i can stay around 14.4 Volts, then i'll consider the bigger amp.
derickveliz2Central, MA · Jan 21, 2011#54
Originally Posted by packetrace ↑
I haven't insalled the eq6500 since i dont know where to mount it...and I dont have ampli for the speaker....they are actually wired to the stock wire...so...out of the deck...!


where had you mounted it ?

what kind of good amp should i buy....an amp that i could do a 3-way component like yours but later on!

thanks
I would install the eq6500 under the steering wheel or inside the glove compartment.

Since you all ready have a Hifonics you could get a HFi100.2 and run passive 100x2 into the 6.5 + Tweeters Passive means that you are going to use the x-over between the amp and the speakers.

HFi100.2 LINK

Picture not included in this copy

You could still run passive with a 3 way system with a x-over and not breaking the bank going Active, and still use only 2 amps 1 for the sub and 1 for the speakers (Mid-bass 6.5", 3" mids, tweeters)

Then if you really want to go 3 way active, it's a complete different story.

D.
_S7V7N_South Texas · Jan 21, 2011#55
http://cgi.ebay.com/ebaymotors/NEW-C...item45f7b63f89

* PowerZone Series 4-Channel AB Car Amplifier
* RMS Power Rating:
o 4 ohms: 87.5 watts x 4 chan.
o 2 ohms: 175 watts x 4 chan.
o Bridged, 4 ohms: 350 watts x 2 chan.
* Max Power Rating:
o 4 ohms: 175 watts x 4 chan.
o 2 ohms: 350 watts x 4 chan.
o Bridged, 4 ohms: 700 watts x 2 chan.
* MOSFET power supply
* LED power and protection indicators
* Tuned Bass EQ (0-12 dB bass boost at 45 Hz)
* Variable bass equalization
* Speaker-level inputs with soft turn-on
* RCA Inputs and outputs
* 4-Channel operation
* Top mounted controls for easy adjustment
* 4-Way protection (DC, short, thermal, overload)
* Stereo mono amplifier mode switch
* Illuminated CRUNCH logo
* Silver-plated RCA level inputs
* Silver-plated screw terminals
* Variable high-pass filter (60-1200 Hz, 24 dB/octave)
* Variable low-pass filter (30-250 Hz, 24 dB/octave)
* Variable input level control: 0.2V-5.0V
* Top-mounted controls
* Frequency response: 30-1,200 Hz
* Dimensions: 13-3/8"L x 10"W x 2-1/8"H
* 4-gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits when purchased together with this amplifier.
* 1-year Manufacturer's warranty



Picture not included in this copy
sqcompBack at home · Jan 22, 2011#56
You know...I may be able to get that amp for you right around that price WITH a real warranty...

Our shop is the distributor for Maxxsonics (i.e. Crunch) and gets pretty darned good pricing.
_S7V7N_South Texas · Jan 22, 2011#57
There you go Packet, I'd jump on that deal, i have the older model, and am pretty happy with it. If i could get that newer model for around 85 bucks, I'd sell this one and buy that model there .
packetraceThread starterQuebec · Jan 22, 2011#58
whats the difference between active and passive ? :S
derickveliz2Central, MA · Jan 23, 2011#59
Originally Posted by packetrace ↑
whats the difference between active and passive ? :S
Passive is when you run x-overs like the ones you have, and they go between amp and speakers.

Active is when the x-overs go before the amps.

Note that an active x-over is much more sophisticated than a passive x-over!

I hope it helps

D.
sqcompBack at home · Jan 23, 2011#60
To expand on what Derick is saying...

Electronic Crossover:
A crossover is a filter. It is used to block some frequencies while allowing others to pass with little or no effect. An electronic crossover is a set of active filters which pass/reject part of the audio band. The crossover point is determined by changing the value of resistors and/or capacitors in the active filter circuit. A high pass crossover will allow frequencies above a predetermined point to pass. The frequencies below the crossover point will rolloff at a rate determined by the crossover's design. A low pass crossover would let low frequencies pass while reducing the level of the high frequency part of the signal. The signal from the head unit feeds the crossover. The signal leaving the crossover goes to an amplifier. If the high pass output is connected to an amplifier, that amplifier would be connected to smaller speakers which may include tweeters. A low pass xover would drive an amp connected to larger speakers, including woofers.


Passive Crossovers:
A passive crossover has no active filters as are used in the electronic crossover. It uses coils (inductors) and capacitors to cause a rolloff of the audio level. The simplest types use a single coil OR capacitor connected in series with the speaker. If a capacitor is used, it will reduce the lower frequencies getting through to the speaker. If an inductor is used, it will reduce the higher frequencies getting through to the speaker. In this configuration, the rate of rolloff is 6dB/octave. In a more complex configuration combining both coils and capacitors on each speaker, a steeper rolloff is obtainable.

-BCAE1
packetraceThread starterQuebec · Jan 23, 2011#61
So you got active....?

Your activee x-over are in your HU i guess ?

Does it give a way better sound with active ?

Could I use the same speaker Derick have (HL-70 HAT L1V2 and L6) with passive ?

The type of amp is changing depending on passive or active ?

Thanks
sqcompBack at home · Jan 23, 2011#62
Derick and I have essentially the same source unit. Mine just speaks Japanese! :)

Yes, our sources have the crossover control in the deck. The sound received is subjective. You can mess up your sound just as much as you can improve it with an active crossover section.

Of course you can use a passive setup with any type of speakers (for the most part). What I wouldn't do is just slap a random passive in there. With a homogenized mix of speakers, you're going to have to find your own values for what crossover points you want and then make it for the best results.

Now, for the cost and time savings, you can pick up an active crossover and avoid the hassle and gain more flexibility.

Your amplifier choice shouldn't affect the crossover...however, a lot of amplifiers have more advanced crossovers now days. That's also something to look at...an amplifier that has a nice crossover section to mess around with.
packetraceThread starterQuebec · Jan 23, 2011#63
what kind of active cross over would you suggest me ?
sqcompBack at home · Jan 23, 2011#64
I say buy a decent deck and buy into an RF360.3 or a Bit One. There's a new Bit One coming out that is a smaller version with a few less bells and whistles than the full sized piece. It'll save some cash too.

Alpine, Arc Audio, and Mosconi have some nice processors as well.
packetraceThread starterQuebec · Jan 23, 2011#65
a decent deck turns around how much ?? ahaha

and do you have a link of RF360.3 ...ive made research on google..and found no thing :(
_S7V7N_South Texas · Jan 23, 2011#67
This Is the deck i have and it has alot of tuning options.
Kenwood X794

I got mine for under 175 bucks shipped
Amazon Link


Picture not included in this copy


A few specs

Sound Excellence DSP: In order to optimize the sound quality, you can use the Sound Excellence DSP to set the type of vehicle and speaker sizes, locations, distances and x-over points. The DSP settings include the following:

•Cabin Setting: Choose from Compact, Full Size Car, Station Wagon, Mini Van, SUV, Mini Van (Long), or Off
•Speaker Setting: The speaker X'over is automatically set when the position and size of each speaker are select from the following items.
◦Front: Location (Door, On Dash, or Under Dash); Size: (6-1/2", 6-3/4", 7", 4"x6", 5"x7", 6"x8", 6"x9", 7"x10", OEM, 4", or 5"); Tweeter (None or Use)
◦Rear: Location (Door, Rear Deck, 2nd Row or 3rd Row; Size (6-1/2", 6-3/4", 7", 4"x6", 5"x7", 6"x8", 6"x9", 7"x10", OEM, 4", or 5")
◦Subwoofer: Size(10", 12", 15", None, 6-1/2" or 8")
•Digital Time Alignment (DTA): Choose from 0.00 to 14.44 feet for the Front pair of speakers, Rear pair of speakers, and Subwoofer distances in reference to the distance between your listening positioning and the locations of the particular speakers.
•X'Over: The Kenwood eXcelon headunit provides independent high-pass crossovers for the unit's front and rear speaker/preamp outputs, as well as a subwoofer low-pass crossover.
◦Front High Pass Filter: Frequency (30, 40, 50, 60, 70, 80,90, 100, 120, 150, 180, 220, or 250Hz); Slope (-12, -18, or -24 dB per octave); or you can also select full-range
◦Rear High Pass Filter: Frequency (30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, or 250Hz); Slope (-12, -18, or -24 dB per octave); you can also select full-range
◦Subwoofer Low Pass Filter: Frequency (30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, or 250 Hz); Slope (-12, -18, or -24 dB per octave); Phase (Normal/Reverse); or you can also select full-range
Equalizer Control: Equalizer Control allows you to use one of the System Q presets, or set your own custom settings using the 5-band Equalizer. The EQ adjustments are as follows:

•Preset EQ: You can select from Natural, Rock, Pops, Easy, Top 40, Jazz, Game, iPod (you can select from 22 EQ curve types), or User.
•5-Band EQ: The User mode allows you to adjust the following 5-Band EQ (62.5Hz, 250Hz, 1kHz, 4kHz, 16kHz) settings.
◦Band Levels: Independent front and rear EQ level of -9dB to +9dB.
◦Bass Effect: Enhances the bass response of Band 1 (62.5Hz).
Position Control: For a better sound-stage you can select your optimal listening position. You can choose from All, Front Left, Front Right or Front. You can also select to manually fine tune the sound stage by selecting the distance for each individual speaker in the vehicle compared to your listening position. You can select between 0.00 to 5.58 feet for the Left Front Speaker, Right Front Speaker, Left Rear Speaker, Right Rear Speaker, Left Subwoofer and/or Right Subwoofer.
packetraceThread starterQuebec · Jan 23, 2011#68
There somethings I want to know just to help me understand the whole thing....about active..passive....3-way component...

I can seee on those active x-over you linked me that there is 3 rca output....rear front and sub....rear would be for mid bass and front for tweeter and midrange....but what willl allow HIGH to tweeter and mid-high to midrange speaker....

Would my EQ-6500 act as an active cross over....I have those 3 rca output...rear front sub...
derickveliz2Central, MA · Jan 23, 2011#69
Here is a typical installation, imagine your Eq6500 between your HU and 6xs

Picture not included in this copy
packetraceThread starterQuebec · Jan 23, 2011#70
👍ohhhh there you gooo!! this is the way to do what you do without having a deck of 1500$ !!ahahah

thanks derick....im pretty visual...so an imagine is worth 1000 words
sqcompBack at home · Jan 23, 2011#71
The payoff with the deck that is "$1500" (actually less than that) is that you have less links in the signal chain and you don't have to leave your seat or use a laptop to adjust anything.
packetraceThread starterQuebec · Jan 23, 2011#72
how much you paid for your carozzeria ? and th p-99 ? aahaha
sqcompBack at home · Jan 24, 2011#73
Probably the same as derick. The only thing I got over the American version is the little amplifier...and Japanese sub menus.

I forecast in a couple years I'll sell the piece and buy into a more advanced processing system. It'd be a long shot to get my hands on a JK Labs type piece.

I know tha SB's processing power is something like 300 dB sloped and a completely infinite parametric equalizer system with a very advanced time alignment process. I'd LOVE to gave the headache of setting that one.
derickveliz2Central, MA · Jan 24, 2011#74
Originally Posted by packetrace ↑
how much you paid for your carozzeria ? and th p-99 ? aahaha
P-99s are around $1200

What I think you would like is:

HU to EQ6500

EQ6500 has 3 rca outputs

. for Sub-Woofer (you all ready have an amp for this)

. (get a 4 channel amp) and you could have

Chanels 1 = a passive x-over with 3" or 4" Mids + tweeter

Channel 2 = 6.5" (Mid-bass) in doors (you can use the built in x-over in the amp)




Picture not included in this copy

D.
packetraceThread starterQuebec · Jan 24, 2011#75
I like much more the one with th 6XS audiocontrol...because i want to change as often as I want the filter.....but I've talked with one of my teacher at college...and I could built a circuit with a PIC and I could program it as a filter.....and build one for tweet, mid bass sub.....but it would be between speaker and amp.....

ps: we are actually drawing our schema for a subwoofer amp....we'll have our amp in MAY or early !
packetraceThread starterQuebec · Jan 25, 2011#76
Is there some deck with 4 outpout like yours p-99 but for less then 1200$....around 500$ ?

because its mcuh more wire with my actual HU....HU to eq6500 to 6QS to AMP

Thanks...and would you have a kit of tweeter,mid-range and mid-bass to suggest me....not as expensive as your system....but....not a crappy system ....

THANKS👍👍
packetraceThread starterQuebec · Jan 25, 2011#77
I took a look at some amp...and found this....

Picture not included in this copy

4 ohms: 75 watts x 4 chan. + 250 watts x 1 chan.

2 channel for tweeter, 2 channel for mid range and 1 channel for mid bass.....would iit work?
sqcompBack at home · Jan 25, 2011#78
Powerbass is a good choice. The "lower power" for the sub might lead me to use a ported enclosure for a bit more output. You could also use two small woofers as well.
packetraceThread starterQuebec · Jan 25, 2011#79
i already my amo + sub....the channel ''sub'' on the powerbass would be for my MIDBASS.....which would go in the door...maybe kickpanel...but IN A WHILE
sqcompBack at home · Jan 25, 2011#80
I was under the impression that mid bass would be stereo instead of mono.
packetraceThread starterQuebec · Jan 25, 2011#81
You're right ! newbie I am....!! it would be better to take a PB a 4channel for mid and tweeter...and a 2 chanell for midbass.....and my sub i already have all i need!
packetraceThread starterQuebec · Jan 25, 2011#82
2 powerbass amp would be really good i guesss......

what kind of 3 way component should I be looking for....? I'D like to do something like derick...in ball on a-pillar...or maybe fiberglass...
sqcompBack at home · Jan 25, 2011#83
How about looking for what you want on the net, show us what you are thinking. I've got TONS of pictures of component builds, I'm sure Derick does as well.

...Derick does have a good setup. I wonder who helped there? :P Why not describe what kind of listening you're going to do and we can tailor something for you.

Here's mine:

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Any ideas?
derickveliz2Central, MA · Jan 25, 2011#84
Originally Posted by packetrace ↑
I took a look at some amp...and found this....

4 ohms: 75 watts x 4 chan. + 250 watts x 1 chan.

2 channel for tweeter, 2 channel for mid range and 1 channel for mid bass.....would iit work?
That is the amp I'm using to power my Mids, Tweets and Subwoofer.

Channel #5 is in Mono! It won't work for Midbass you need stereo!



Picture not included in this copy

D.
sqcompBack at home · Jan 25, 2011#85
Nice looking amp! Is everything going okay with it? (customer service checkup)
packetraceThread starterQuebec · Jan 26, 2011#86
I'm listening to a lot of kind of music!

Most of the time I listen to punk music....just like sum41, Blink182


ps:your system looks sooo great !! I Like those 3 amp mounted in the back!! and ypour tweeter+mid-range in the A-Pillar! WOOW
sqcompBack at home · Jan 26, 2011#89
...just wait until you see the finished trunk. I'm floating the ML3800 sub woofer with the magnet out in front of the amps as you look into the trunk. I layed down the frame and the bottom glass yesterday. Next week will be more glass buildup. I'll have around a cube and a half for the enclosure.

Anyway, one word of warning, With the ebay purchases...watch yourself. Woofersetc isn't an authorized retailer for Elettromedia. 9 month warranty? Seriously? That's an in house trick. You won't be getting factory support if something goes wrong.

You're closer to Palmer than I am to you. Perhaps one of us can work something out for you to get the real product.
packetraceThread starterQuebec · Jan 26, 2011#90
Im looking at your trunk...and WOW i just like too much tha amp!!! maybe I could do that....It wont be that beautiful because I wont have 3 amp of the sam brand....👎

Where can we buy Hertz audio product....?
sqcompBack at home · Jan 26, 2011#91
There are two camps to the buying idea. I'm on one side which supports brick and mortar stores.

PM me your address. I think I can match that woofersetc ebay price on the HSK 163 set and get it to you for basically the same price overall. That way you'd have a real factory warranty for the same price as the rip off woofersetc 9 month in house (non authorized) "warranty".

I'm thinking that the second set is an older set. That's an attractive price as I'm seeing it for the two way. It's old however...
sickpuppy1Kansas · Jan 26, 2011#92
Gotta figure in the 50.00 shipping too!
Palmer812North Carolina · Jan 26, 2011#93
FYI! I don't know of anyone personally that has ordered Hertz from Woofers Etc. but according to Electromedia USA (Hertz/Audison) Woofers Etc. doesn't even have any Hertz speakers at all. Period. They wanted to be a dealer and Hertz refused to sell to them and they got mad. They still advertise that they have it but when you order ut they (bait and switch) you. They do however have some older Audison amps they acquired from a dealer who went out of business. Hertz/Audison refuses to warranty ANYTHING that comes from them.
derickveliz2Central, MA · Jan 27, 2011#94
Originally Posted by sqcomp ↑
Nice looking amp! Is everything going okay with it? (customer service checkup)
Thank you,

Yes every thing is OK, a big improvement from my old Premier Pioneer amp.

One question, it makes a little noise when turns on/off on the speakers, my Pioneer amps never did, when on sounds like "Thrrrst" and when off sounds like "Tukk"

listen to this VIDEO...

or...

http://www.youtube.com/watch?v=HvFqMbs5VN0

Picture not included in this copy


Thanks

D.
sqcompBack at home · Jan 27, 2011#95
@Palmer...

That is EXACTLY what my shop owner said! Bait and switch.

@Derick:

Check your grounds carefully. In order for the amps to function properly, the audio ground must be referenced to chassis ground at the source unit. If it is not, the amplifier could oscillate. To check for a good ground reference, take a volt-ohm meter (VOM) and measure the resistance between the chassis of the radio and the shield of the RCA line level outputs of the radio. This reading should indicate a direct short. If this is not the case, grounding the shield of the RCA line level outputs to the chassis of the radio will probably be necessary. Keep amplifier power ground wires as short as possible. The longer a wire, the more resistance it has. When a current flows through a resistance, a voltage drop is produced. Because of this, the ground reference at the amplifier's circuit board is no longer the same as that at the chassis of the vehicle. This ground potential differential can lead to noise and improper operation of the amp. (-W.H.)

I'll show Jim this if we can't solve this soon.
packetraceThread starterQuebec · Jan 27, 2011#96
Welll....looks like ebay wont be a great choice....:O I'll forget ebay buying !
packetraceThread starterQuebec · Jan 28, 2011#97
Have you seenn this yaris build on DIYMA ???👍👍👍👍
sqcompBack at home · Jan 28, 2011#98
What build? Derick's?
sqcompBack at home · Jan 28, 2011#100
I remember this install. at some point I had communication with the builder on this one. There were some suggestions on the door assembly...