Yarisworld Archive

Found : head gasket oil leak on 2 used 2010 YARIS ...

197 posts · 86,523 views · page 4 of 4

Replies continued

HersheyThread starternortheast · Apr 7, 2011#151
This is also the reason why we and our friends ( told them of our experience ) are hesitant to get the M.L.S. h.c.g. of the 2010s' replaced under warranty . He has 65,000+ miles on his 2010 3 door . He bought the 4 year / 125,000 PLATINUM extended warranty at time of purchase . So , he's keeping his fingers crossed for the car not to develop any issue with the oil leak of his YARIS after the warranty runs out . We're using his car as a guinea pig since we only put on about 15,000 miles a year , which is well below his yearly average .
HersheyThread starternortheast · Apr 7, 2011#152
This picture is of a 2007 YARIS engine torn down at 102,000 miles , said to be due to an external oil leak and internal coolant leak . Good to know the PLATINUM extended warranty with 0 deductible is there as the mileage / years pile on .
cylinders.jpg
HersheyThread starternortheast · Apr 8, 2011#153
Top view of the black M.L.S. h.c.g.. The area circled in BLUE is where the gasket is split ( gap ) . The area in RED is where the h.c.g. leaks oil from underneath the gasket of the #1 cylinder . Picture below shows the split in H.C.G. , circled in RED .
cylinders.jpgGEDC0890.jpg
CB900F2Toronto · Apr 9, 2011#154
Add me to the list of leaking head gasket 😠

Checked about three weeks ago when I came across this thread, and cleaned up the area and oil is slowly coming back in the same area.

Anyone consider getting a coolant fluid analysis as there is a coolant passage just to the top left of the cyclinder#1 and wondering if the oil is making its way also in to the coolant in addition to leaking out?
bronsinnj · Apr 9, 2011#155
Originally Posted by CB900F2 ↑
Add me to the list of leaking head gasket 😠

Checked about three weeks ago when I came across this thread, and cleaned up the area and oil is slowly coming back in the same area.

Anyone consider getting a coolant fluid analysis as there is a coolant passage just to the top left of the cyclinder#1 and wondering if the oil is making its way also in to the coolant in addition to leaking out?
Im curious if you could give an estimate of how much oil this is? Is it measureable on the dipstick? The question isnt is oil going into the coolant but is coolant burning in the combustion chamber? Which should be apparent from white smoke and lowered coolant level. Also if there IS oil in the coolant it will be seen in the radiator when you take the cap off. (engine cold please)

See any?
HersheyThread starternortheast · Apr 9, 2011#156
If there's an internal coolant leak it would be very slight within the cylinder and most of it is likely to burn off within the cylinder . You'll notice there's more deposits in the #1 cylinder of the torn down engine above . We've just posted a U.O.A. in this section for the 2010 and no signs of coolant were present in the analysis . Plan to do oil analysis for it every 35 > 40,000 miles . Might get a compression test for the 2010 as well . Yes , there is some drop of the oil on the dipstick .
HersheyThread starternortheast · Apr 9, 2011#157
There's been a few other members that claimed to have or possbily have the oil leak , but they've disappeared . 🤷 . One said they found out through CARFAX that the head cylinder gasket was replaced on their used '09 and another discovered the oil leak when working under the car while installing fog lights . Maybe they're just playing with our heads .
HersheyThread starternortheast · Apr 9, 2011#158
Originally Posted by CB900F2 ↑
Add me to the list of leaking head gasket 😠

Checked about three weeks ago when I came across this thread, and cleaned up the area and oil is slowly coming back in the same area.

Anyone consider getting a coolant fluid analysis as there is a coolant passage just to the top left of the cyclinder#1 and wondering if the oil is making its way also in to the coolant in addition to leaking out?
Sorry to see that . You could get a U.O.A. to see if any coolant is present , like we did .
HersheyThread starternortheast · Apr 9, 2011#159
THIPHIL , is the one that supposedly found oil on the back of the block while installing fog lights on his 2010 ( posted March 24 , '11 ) and then on MARCH 26th posted he was taking it to the dealer the following week . No word since .
HersheyThread starternortheast · Apr 9, 2011#160
Then these's a post with a few pictures by GONZO452001 of possible oil leak in this thread on page 7 , post #123 . Never heard from again .
HersheyThread starternortheast · Apr 9, 2011#161
Then there's this post ( 1/8/'11 , post # 83 , page 5 this thread ) by TXyaris finding the head cylinder gasket was replaced on his used 2009 by using CARFAX . Nothing since .
HersheyThread starternortheast · Apr 11, 2011#162
Yesterday we stopped by the friends for a visit and to get pictures of the extent of the oil leak from the H.C.G. of their 2010 3 door bought new in October , 2009 . The last time I thoroughly cleaned the exposed part of the black M.L.S. head cylinder gasket and the surrounding area was October 19 , 2010 with around 49,000 miles on it . So , it's been close to 7 months since last inspection . There's now over 65,000 miles on it . There was no oil leaking from the valve cover gasket and no oil on the top or the back of the valve cover from oil changes done at a TOYO dealer . I've posted pics from our 2010 3 door of same areas that were recently cleaned as his was in October , 2010 to give the BEFORE ( cleaned ) and AFTER ( around 16,000 miles later ) . Here's what was discovered :
GEDC0797.jpgGEDC0908.jpgGEDC0883.jpgGEDC0919.jpgGEDC0866.jpgGEDC0922.jpgGEDC0633.jpgGEDC0930.jpgGEDC0167.jpgGEDC0942.jpgGEDC0940.jpgGEDC0946.jpg
HersheyThread starternortheast · Apr 11, 2011#163
" toyota put that black gasket maker in there? really? they made a mess of a job. "

Can you imagine how much of the black Form In Place Gasket ( F.I.P.G.) sealer that may have ended up inside the engine as well . I did several short runs of fresh oil and filter to flush out any that may have been inside the engine . This is part of the reason we'll be getting an U.O.A. for the 2008 sedan in mid MAY . Will post that .
HersheyThread starternortheast · Apr 11, 2011#164
Plan to go back to our freinds 2010 YARIS and then mark the coolant level in the resorvoir when it's cold . That way I can hopefully monitor it to see if any coolant is being lost . Worth a try .
auxmikeLI, New Yawk · Apr 11, 2011#165
Hershey, my gasket appears to be still ok, but I need avisual to verify it. Gotta jam the camera in there still....
CB900F2Toronto · Apr 11, 2011#166
Use a mirror

Originally Posted by auxmike ↑
Hershey, my gasket appears to be still ok, but I need avisual to verify it. Gotta jam the camera in there still....
CB900F2Toronto · Apr 11, 2011#167
Rockland.. How many head gasket replacements have you seen at your dealership for the Yaris?

Thanks Rockland

Originally Posted by ROCKLAND TOYOTA ↑
i call 🙄 until this guy posts up some pictures in a toyota dealer's lot with said leaks....
HersheyThread starternortheast · Apr 12, 2011#168
" Hershey, my gasket appears to be still ok, but I need avisual to verify it. Gotta jam the camera in there still... "

I've had plenty of practice with photo shoots of modeling YARIS engines with oil leaks . Get to know the angles , lighting , etc.. These last photos of our friends 2010 YARIS aren't too pretty are they ? May have to open a studio just for YARIS with oil leaks .
HersheyThread starternortheast · Apr 12, 2011#169
Reason why we're posting of the head cylinder gasket issue is that we don't want to see those who own a new / used YARIS to possibly encounter a H.C.G. failure after the 5 year / 60,000 mile warranty runs out which would be an expensive fix out of their pockets . We can understand how this could make owners a bit uneasy . Not wanting their vehicle touched because of possible issues with the car during and after the fix . It's their car , their call . Here again is the picture of a YARIS owner who had the M.L.S. head cylinder gasket replaced at a 102,000 miles by a TOYOTA service center said to be due to the external oil leak and an internal coolant leak . Most likely at the owners expense . TOYOTA needs to come forth on this matter .
cylinders.jpg
HersheyThread starternortheast · Apr 13, 2011#170
Here's the pics Gonzo452001 took of their 2008 3 door located on page 7 , post #123 from March 2nd , 2011 , Found : head gasket oil leak on 2 used 2010 YARIS ... . I've also included pictures of our 2010 YARIS 3 door with area cleaned , AUXMIKES pic , and our friends 2010 3 door for comparison of all 4 cars . Never heard back from Gonzo452001 . I plan not to clean off the oil that leaks from the M.L.S. h.c.g. of our 2010 for about 10,000 miles to see how oil / grime ( dust ) builds up for comparison to AUXMIKE , GONZO452001 , and our friends 2010 . Will take awhile . Top is our 2010 cleaned of oil , GONZO ( 2 pics of '08 ) , AUXMIKE ( 1 pic of '08 ) , and 3 pics of the friends 2010 3 door . May need to ZOOM out a bit for better look .
GEDC0845.jpgbens%20yaris%20001.jpgbens%20yaris%20002.jpgP1000600.JPGGEDC0924.jpgGEDC0930.jpgGEDC0942.jpg
HersheyThread starternortheast · Apr 16, 2011#171
Will be monitoring how much oil gathers on the block from the H.C.G. as time and miles build up for comparison to pics above . Thoroughly cleaned the area of oil / residue before the oil change at 16,611 miles on March 7 , 2011 . Here's pictures taken at 18,053 miles on March 16 . There's 1,442.4 miles (Trip B ) on the oil since the O.C.. You'll notice a small amount of oil circled in BLUE .Theres' also a thin coating of oil on the whole area that has a sheen ( glimmer ) to it , but since being fairly fresh oil it's hard to see , but is wet to the touch . Clearer image when ZOOMED out at 50 > 75% .
GEDC1045.jpgGEDC1068.jpg
HersheyThread starternortheast · Apr 16, 2011#172
Will also monitor the coolant level of the resorvoir for the 2008 sedan since the multi layered steel head cylinder replacement at 23,747 miles due to the same oil leak of the H.C.G.. Marked the coolant level with a black permanent magic marker after sitting overnight at 43 degree temp . Here's pictures of the level , hopefully there will be no loss of coolant . Will keep tabs ( when coolant cold ) and post if any loss . Clearer image when ZOOMED out at 50 > 75% .
GEDC1096.jpgGEDC1095.jpg
CB900F2Toronto · Apr 22, 2011#173
Hershey and all....
I have been monitoring the block for about 2 weeks now ever since I wiped down the area, and so far, there are no visible signs of oil. I did go one step further and you guys may want to try. I took a white piece of stiff paper and used it like a shim and I was able to insert it in between the head gasket and cylinder head and then between the block and the head gasket and ran it along the area in Henrys photo as I wanted to see if there was any oil reside still in this area, and the paper came out clean, no oil.

Not sure what this means at this point, but I am hoping that maybe my situation is only that the oil might have come from the timing chain cover area and just ran along the block (maybe!)...

Feedback from other members would be great..

P.S.. Henry I re used you photo. I will upload one of my photos
Gasket.jpg
HersheyThread starternortheast · Apr 22, 2011#174
Let the car go for awhile to see if it ends up like this ( 2010 Yaris ) . If not , then maybe you're in the clear . Thanks for the effort .
GEDC0651.jpg
CB900F2Toronto · May 8, 2011#175
Hey guys.. So far, every day I have been monitoring the head gasket, and it appears at this point, I may just have a very small leak at the point where the timing cover and the block/head meet. I attached a photo where about every 2 to 3 days, there is a very small amount of oil, and I have to use a q-tip to actually see it by wiping the area with the the q-tip. I checked with the q-tip the area around the actual gasket, and along the block(HG) and no oil.

I attached a photo of the area.
Gasket.jpg
HersheyThread starternortheast · May 8, 2011#176
The oil comes from under the H.C.G. and runs down along the sealant of the timing chain cover and also runs under the the ledge as I pictured above . Did you look from under the car up to the bottom of the ledge where oil collects underneath ? Thanks for posting and sorry to see your car leaks oil .
HersheyThread starternortheast · May 8, 2011#177
Don't forget the '08 sedan had the same oil leak that ran down along the sealant of the timing chain cover to the lip of the oil pan and no longer leaks since the replacement of the factory H.C.G..
CB900F2Toronto · May 8, 2011#178
Hi Hershey... In my case, there is no oil on the underside of the same area.. I did use the shim check as noted in another one of my post during the past few weeks and no oil.

Will keep a close eye on the situation and will post updates


Originally Posted by Hershey ↑
The oil comes from under the H.C.G. and runs down along the sealant of the timing chain cover and also runs under the the ledge as I pictured above . Did you look from under the car up to the bottom of the ledge where oil collects underneath ? Thanks for posting and sorry to see your car leaks oil .
HersheyThread starternortheast · May 9, 2011#179
May want to let it go for a week or so to if it builds up . Then check . Hopefully you're fine . Will likely post an used oil analysis for the 2008 sedan that had the head cylnider gasket replaced at 23,747 miles in the begining of last September and no oil leaking from the #1 cylinder as of yet ( 30,945 mis. ) . It may be loosing coolant since the repair and there was an excessive amount of TOYOTA black form in place gasket ( F.I.P.G. ) silicone sealant used during the repair under warranty . Will be interesting to see if any signs for one or both . Best of luck to you and your YARIS .
HersheyThread starternortheast · May 9, 2011#180
During the O.C. earlier I noticed some black pieces in the opening of the oil fill hole . Looks to be pieces of the black silicone sealant used during the fix . The tech went overboard with the sealant . Plan to try to open the oil filter to see if any silicone gathered in it . Here's a pic of the oil fill hole and outside of engine where there's the black F.I.P.G. sealant all over it . Makes you wonder how much ended up inside the engine . Top pics are the back of timing chain cover / valve cover and the bottom picture is of some black pieces ( circled in BLUE ) inside oil fill hole of valve cover . There were also many pieces in the bottom of the bucket where the used oil was drained into . This was the 3rd O.C. since the repair and these black pieces are showing up .
GEDC1007.jpgGEDC0890.jpgGEDC1148.jpg
TXyarisTX · May 9, 2011#181
Originally Posted by Hershey ↑
There's been a few other members that claimed to have or possbily have the oil leak , but they've disappeared . 🤷 . One said they found out through CARFAX that the head cylinder gasket was replaced on their used '09 and another discovered the oil leak when working under the car while installing fog lights . Maybe they're just playing with our heads .
LOL I was serious about the carfax thing.
HersheyThread starternortheast · May 9, 2011#182
" LOL , I was serious about the carfax thing. "

I'd hope you weren't yanking our dipsticks . Been awhile . How's it working out for you ? How about posting the CARFAX , if it's possible ( minus part or all of the V.I.N. ) . The more the merrier for those who disbelieve .
HersheyThread starternortheast · May 18, 2011#183
If possible post some pics of the oil that has gathered . Would be an easy task for you with the rack . No crawling under the car , standing room . Good luck .
HersheyThread starternortheast · May 19, 2011#184
" well, I gave yari the "reach around" and snapped a pic with the GF's iphone.

Thanks for taking the photo .

" seeping all the way down the timing cover. "

This is how I found the '08 sedan with 17,893 miles and the 2010 3 door with 3,467 miles at the time of the O.C. for the sedan . Then checked the 2010 after finishing O.C. for the '08 . Also was on the top of the oil pan . Our friends 2010 3 door is very similar to yours . Have been monitoring that since last September .

" There is no oil dripping from the car, but there is significant seepage extending all the way to the oil pan gasket. "

Some oil would most likely fall to the ground when driving , due to it accumulating on the top of the oil pan . The dipstick for the 2010 would drop about 1/4" below the full mark by the time for next O.C. ( 4,000 + mis. ) .

My next step will be removing the engine cover to rule out any spilled oil during O.C's, then trying to get a visual on the source, clean the whole area/engine down and run it for a couple hundred miles, then repeat.

Good plan .

" The oil is ready to be changed so I will also pull a sample to send to blackstone. That should tell the whole story. "

It may . The U.O.A. I posted for the 2010 in the D.I.Y. forum shows no contaminants at 16,611 miles on the engine . The higher mileage you have could present an issue . Won't know until you send it in .

" I will run a compression test "

We never had that done . Did think of it . The oil comes from the #1 cylinder of the H.C.G. , cylinder 1 is closet to the timing chain ( you may be already aware of that ) . Be interesting to see if that is possibly lower than the others . Let us know your findings .

" I am out of warranty "

Not the case . You should be covered under the 5 year / 60,000 mile powertrain warranty .

" I am hopeful that this is a " benign " head gasket seepage problem , and oil is only seeping externally . We'll see !!! "

We're watching our friends 2010 3 door ( 70,000+ mis. ) to see if the H.C.G. craps out , hopefully not . May end up looking like this at 102,000 miles .
cylinders.jpg
thefallsSunny place · Oct 9, 2012#185
Bumping this thread,as i recently discovered that a few 1nz fe have this leak.
A friend with the boosted TRD motor has the leak close to the timing chain cover and head/block region. Its nothing spectacular but the block is 'damp' with oil around this area.

So what you you people have done?

Replace the head gasket and torqued the head more?

Or just replaced the head gasket?

Thanks.
yaris2010RSAngus, Ontario · Dec 7, 2012#186
hate to be the one to bring an old thread back to life, but after removing my 2010 engine i took some pics. i think these will be the most clear pics in this thread and do point towards an issue with the head gasket sweating oil. Also possibly a new "ledge" to check for oil residue. Please keep in mind, i know i had an exhaust leak at my header, that is definatly not the cause of the residue. I will post more pics once i tear down into the engine more.

Picture lost · i1194.photobucket.com

Picture lost · i1194.photobucket.com

Edit to highlight key points

Green - Head gasket
red - Oil residue (sweating gasket) area
Blue - Exhaust leak
RED ARROW - seating gasket, THERE IS NO OTHER WAY FOR OIL RESIDUE TO GET THERE

Picture lost · i1194.photobucket.com

Picture lost · i1194.photobucket.com
bronsinnj · Dec 7, 2012#187
Personally if I had this happen to me I would monitor the oil consumption very carefully.
Also I would put a piece of cardboard on the ground under the engine and park it there every night.

If the oil didnt fall much on the disstick and there wasnt much oil on the cardboard, I would leave it alone! Theres more trouble to be had by strangers I dont know if they know what theyre doing taking apart the engine and "fixing" it. Also, who is to say a new head gasket WILL fix the problem? What if it doesnt? What if the well meaning people at Toyota screw something else up?

If the compression goes south and the engine starts burning coolant that would be different.

Does anyone know exactly were under the HG the oil is coming from? Maybe that can be modifyed?

One thing bothers me is the reports of new Yaris's with overfilled crankcases. The oil needed is 3.7 qts probably they are putting four liters full in there. Could that do it?
jRossIndianapolis, IN · Dec 7, 2012#188
This thread is painful to read, i'll be checking my block later... i did glance around there before i bought the car but now i'm going to check this specific area. Even if i am leaking, i would probably take bronsin's approach, i've had slow leaks on cars before that didn't cause major damage during the time i drove it.
HersheyThread starternortheast · Dec 7, 2012#189
I say , let it be . Our friends' 2010 has the same leak since new and there's over 125,000 miles . Just check the level every week .
HersheyThread starternortheast · Dec 7, 2012#190
I've found a few SCION XBs that have the same engine as the YARIS to have same oil leak . Not sure about the XAs . Rarely see those at used car lots .
yaris2010RSAngus, Ontario · Dec 7, 2012#191
Hershey, lets not jump to conclusions and make a pandemic over something that isnt proven.

Please note i have been monitoring this since 2010 when i got my car and it was always existent but i never once noticed oil on the ground under my car, even after it sat for numerous days at a time. Also i never once noticed my oil dip stick dropped, even after i was boosted i only once noticed an oil drop and it was due to a seperate oil leak on a turbo line.

another note, my car parks in the same spot every night in my garage, the same way. there has never been an oil drip on my white concrete floor.

All that being said, this oil debris was visible on my 2010 yaris since about 4-6 months old (when i first checked)

I do believe My car is not a perfect example as it was oil changed at the dealer since day one and im not 100% sure they did not ever "miss" the oil fill hole. i do believe if they were missing and some was running down the back of the engine i would smell a burning when it hit the header and also the chances of just missing enough to run down the back of the engine and stop on the ledge without going any lower is a long shot. I am comfortable in saying some of this collection of oil and debris could have been caused from oil change sloppyness but i am not able to say that all of this has been caused from oil change sloppyness.

I will attach more pictures soon of the head gasket, from impressions in the head gasket i can say i did not see any failed points but the possibility of raw exhaust (carbon, oil, and other compression debris) blowing through the 2 piece layered head gasket.

Calling this a "Leak" may be premature and incorrect, i am still leaning towards the gasket sweating out between them.

Something else to note, the 2 head bolts on the timing chain edge did seem not as torqued down as the other bolts.
HersheyThread starternortheast · Dec 7, 2012#192
I'm fine with it now . It's oil under the pan . 😁
nookandcrannycarS.MontgomeryCnty,TX(HoustonMSA) '07=BayouBlue=300,125miles=OrigOwnr '14=ClassicSilvr=29,059miles · Dec 8, 2012#193
Originally Posted by Hershey ↑
I've found a few SCION XBs that the same engine as the YARIS to have same oil leak . Not sure about the XAs . Rarely see those at used car lots .
Agreed. i don't see as many XAs out on the road either.
nookandcrannycarS.MontgomeryCnty,TX(HoustonMSA) '07=BayouBlue=300,125miles=OrigOwnr '14=ClassicSilvr=29,059miles · Dec 8, 2012#194
Originally Posted by Hershey ↑
I'm fine with it now . It's oil under the pan . 😁
Pun of the Day 😁.
mattme33Florida · Apr 23, 2013#195
Hey everyone,

Just wanted to report that my 07 Yaris Sedan (automatic) is having this issue. I am well beyond my warranty in years but not mileage. Warranty will not cover the issue. The fix was quoted as "Engine oil leaking from front cover, reseal cover, replace front crank seal & valve cover gasket" for which I am quoted the price of $502.00 + tax

1.) Is this really going to "Fix" the issue
2.) Is this price fair?

Thanks for any help on the issue.
YarisSedanCalifornia - Bay Area · Apr 23, 2013#196
Originally Posted by mattme33 ↑
Hey everyone,

Just wanted to report that my 07 Yaris Sedan (automatic) is having this issue. I am well beyond my warranty in years but not mileage. Warranty will not cover the issue. The fix was quoted as "Engine oil leaking from front cover, reseal cover, replace front crank seal & valve cover gasket" for which I am quoted the price of $502.00 + tax

1.) Is this really going to "Fix" the issue
2.) Is this price fair?

Thanks for any help on the issue.
Well are you seeing oil on your driveway from the pictures I have seen I'd doubt anyone would loose more than half a quart of oil between oil changes of that so I'd say just monitor your oil level and then repair it when it becomes a issue or gets worse check your pcv valve
HersheyThread starternortheast · Apr 23, 2013#197
I'd let it slide for now . Clean the areas and watch . Check P.C.V. as stated above and replace if needed . Takes about 15 minutes to replace . Longer if stubborn . Use an closed end wrench to get leverage . May want to check the rear corner and the back of of valve cover on the passenger side . That could be a a culprit . Remove any residue in that area . Would also clean any oil from top of the valve cover that may been spilled during oil changes . Do this when checking P.C.V.. I use window cleaner to cut through oil resdue / grime . You'd be amazed how well it works . Paper towels used to remove grime / oil .