Yarisworld Archive

xB final drive swap

65 posts · 38,521 views · page 1 of 2

Jason@SportsCarOriginal postDebary, FL · Aug 12, 2010#1
If anyone is interested, we have done the xB final drive (4.312) swap in our Yaris, fits and works perfectly.

Parts needed from Toyota/Scion:
33321-52110* this part has been superseded new number is 33321-52111 output shaft
41221-52270, ring gear
90105-11040, ring gear bolts (8)

Depending on mileage you may also want to replace bearings and seals, but you don't need to source those from Toyota.

Replies 64

2manywheelsCanada · Aug 12, 2010#2
Thanks for the info man!!
CUrious.. what does that do for the Yaris??
Jason@SportsCarThread starterDebary, FL · Aug 12, 2010#3
Originally Posted by 2manywheels ↑
Thanks for the info man!!
CUrious.. what does that do for the Yaris??
Makes it accelerate quicker.
2manywheelsCanada · Aug 12, 2010#4
So.. if I had a second motor that was being "built" this could be a great addition to the package? I am assuming this is for the manual tranny
darkMINIC-Springs · Aug 13, 2010#5
It works for manual or automatic, it changes your gear ratio. Similar to running shorter tires. Of course you will lose top speed considerably and your speedo will be off(reading faster than you are actually going), so if you do any highway driving ... you will be sad. :(
Nevertheless it's an awesome mod for the track and would probably benefit from the addition of a limited slip differential as well.
Jason@SportsCarThread starterDebary, FL · Aug 13, 2010#6
Originally Posted by darkMINI ↑
It works for manual or automatic, it changes your gear ratio. Similar to running shorter tires. Of course you will lose top speed considerably and your speedo will be off(reading faster than you are actually going), so if you do any highway driving ... you will be sad. :(
Nevertheless it's an awesome mod for the track and would probably benefit from the addition of a limited slip differential as well.
The car will be quicker all the way to the 117mph speed limiter. 👍 Ever driven an xB, this is the same gearing.

You would think the speedo would be off with a gear change... But Toyota must be pulling the signal from the output shaft, or axle, because ours did not change at all. 🤷 Its not like doing a gear change in a rwd car where the signal is pulled from the trans.
ROCKLAND TOYOTAROCKLAND COUNTY NY · Aug 13, 2010#7
RING GEAR part# for AUTOMATIC is: 41221-52090.......
hatchbackkid82. · Aug 13, 2010#8
Just called my local dealership they want about $580 for all the parts😲 Any one know if this mod is really worth the cost of the parts and the hours spent taking the tranny apart?🤷

Why not just get the XB tranny?
TamagoOff Grid · Aug 13, 2010#9
Originally Posted by hatchbackkid82 ↑
Just called my local dealership they want about $580 for all the parts😲 Any one know if this mod is really worth the cost of the parts and the hours spent taking the tranny apart?🤷

Why not just get the XB tranny?

if it's worth it to you to have shorter gears, then it's worth it 🤷

the actual transmission case will not fit without modification (from the xA or xB) in the yaris (confirmed by Morgan)

however, you could purchase a used xA/xB transmission from car-part.com or a local junkyard for less than $200 and disassemble it yourself, you'd only need to buy wear-parts from toyota.

be careful that you don't purchase a transmission from an older ECHO, as they have a 6bolt ring gear, and the scions have an 8bolt ring gear.

i personally HATED the short gearing in the scion. 4300rpm at 80mph was annoying, and did not yield very good mileage. the ECHO transmission i had in the xA was awesome, and my mileage improved almost 10%. the only time i missed the shorter gears was on very tight autocross courses.
hatchbackkid82. · Aug 13, 2010#10
HOLY CRAP 4300rpm at 80 mph😳

It's like you were always in VTEC😁

That would be hell for me considering, I have a modified nitto mid pipe with one resonator

Originally Posted by Tamago ↑
if it's worth it to you to have shorter gears, then it's worth it 🤷

the actual transmission case will not fit without modification (from the xA or xB) in the yaris (confirmed by Morgan)

however, you could purchase a used xA/xB transmission from car-part.com or a local junkyard for less than $200 and disassemble it yourself, you'd only need to buy wear-parts from toyota.

be careful that you don't purchase a transmission from an older ECHO, as they have a 6bolt ring gear, and the scions have an 8bolt ring gear.

i personally HATED the short gearing in the scion. 4300rpm at 80mph was annoying, and did not yield very good mileage. the ECHO transmission i had in the xA was awesome, and my mileage improved almost 10%. the only time i missed the shorter gears was on very tight autocross courses.
TamagoOff Grid · Aug 14, 2010#11
to answer the speedo question from earlier:

because the speedo ring gear turns the same speed as the axles, changing the ratios before it would not affect your speedometer readout.

it's possible that ABS equipped yarii derive speed from the wheel sensors themselves, but that would be a question to be answered by CTscott or someone who's looked over the ecu wiring for ABS/NON equipped cars.
cali yarisCanoga Park, CA · Aug 14, 2010#12
Just called my local dealership they want about $580 for all the parts
You can pick up an xB trans for less than $500 and just pull the parts from that.
TamagoOff Grid · Aug 14, 2010#13
Originally Posted by Tamago ↑
however, you could purchase a used xA/xB transmission from car-part.com or a local junkyard for less than $200 and disassemble it yourself,.
Originally Posted by cali yaris ↑
You can pick up an xB trans for less than $500 and just pull the parts from that.
exactly ;)
Jason@SportsCarThread starterDebary, FL · Aug 16, 2010#14
Just make sure if you are going to the trouble to do the gear change you put in an LSD at the same time. 👍
Jason@SportsCarThread starterDebary, FL · Aug 16, 2010#15
Originally Posted by hatchbackkid82 ↑
Just called my local dealership they want about $580 for all the parts😲 Any one know if this mod is really worth the cost of the parts and the hours spent taking the tranny apart?🤷
WOW, we got ours from TRD for a fraction of that. TRD racer support program: http://www.trdusa.com/thegarage.cfm?team=grassroots

And after racing the car at Miller this past weekend, the gear change has been one of the most effective mods yet.
2manywheelsCanada · Aug 16, 2010#16
Any footage from Miller?? :)

hehe..
Video whore here.. lol
Jason@SportsCarThread starterDebary, FL · Aug 16, 2010#17
Originally Posted by 2manywheels ↑
Any footage from Miller?? :)

hehe..
Video whore here.. lol
There will be.
2manywheelsCanada · Aug 16, 2010#18
Woohoo!!
Thanks for keeping us on on your trials and ventures!!!
Midnight DrifterMonroe, NJ · Aug 24, 2010#19
It's bad enough that Yaris has a "4 1/2" gear with a marginal drop from 4th to 5th, the last thing I need is to be pulling even more RPM's at 75 MPH...

...no thanks.
why?harnett county NC · Aug 24, 2010#20
Originally Posted by Midnight Drifter ↑
It's bad enough that Yaris has a "4 1/2" gear with a marginal drop from 4th to 5th, the last thing I need is to be pulling even more RPM's at 75 MPH...

...no thanks.
I hear you, I'd be tempted to go the other way, or even find a 6 speed box that could help turn the revs down.

But then again, I am not going to race it.
cali yarisCanoga Park, CA · Aug 24, 2010#21
the last thing I need is to be pulling even more RPM's at 75 MPH...
That's the first thing I need. 😉
Bluevitz-rsOshawa, Ontario, Canada · Aug 25, 2010#22
With the 6 speed in my car I turn 2950 RPM (aprox 350 more than the 5 speed) @ 100km/h (62mph) and I'm getting better fuel economy than with my 5 speed.

I average 700+km on 40-42L of fuel. With the 5 speed I'd average 650-680km on the same fuel.
Jason@SportsCarThread starterDebary, FL · Aug 25, 2010#23
Originally Posted by why? ↑
I hear you, I'd be tempted to go the other way, or even find a 6 speed box that could help turn the revs down.

But then again, I am not going to race it.
A 6spd would actually do the opposite. A 6spd is essentially a close-ratio gear box, and 6th gear is only fractionally taller than 5th in a 5spd. And in nearly every case Toyota has outfitted the 6spd with a shorter final drive, which actually means you are spinning the engine more with the 6spd.

If you want to drop your revs put on some taller tires, or drive slower. 😆
MorganPCB, FL · Aug 25, 2010#24
Good luck... 👍
johnny_vitzHamilton, Canada · Sep 9, 2010#25
Originally Posted by Jason@SportsCar ↑
If anyone is interested, we have done the xB final drive (4.312) swap in our Yaris, fits and works perfectly.

Parts needed from Toyota/Scion:
33321-52110, output shaft
41221-52270, ring gear
90105-11040, ring gear bolts (8)

Depending on mileage you may also want to replace bearings and seals, but you don't need to source those from Toyota.

Do you know if the 5 speed trans from an xb will bolt into an echo? And if so, I could use the 8 bolt LSD in it? 🆘
TamagoOff Grid · Sep 11, 2010#26
Originally Posted by johnny_vitz ↑
Do you know if the 5 speed trans from an xb will bolt into an echo? And if so, I could use the 8 bolt LSD in it? 🆘
yes, the xa/xb/echo share transmission mounts. the echo trans is a bit longer, so a swap from an xB to echo would yield slightly more room on the end. the xB comes with an 8 bolt differential, so i'm not sure why you'd be concerned with using an 8 bolt lsd in your 8 bolt transaxle ?
rob323Joyner, Brisbane · Sep 12, 2010#27
For anyone racing their car up and down hills and around corners, the final drive change is the best value for money performance increase I reckon you can do (short of forced induction, if allowed).

The difference for drivers of Echo's is phenomenal. I have a TRD 4.7:1 final drive in my car and there is a steep hill near me that I used to only be able to do about 60kph up it. Basically as soon as I changed into 2nd the gear, the engine didn't have enough power to accelerate and my speed would drop. With the new final drive, I am still slowly accelerating at 80 kph by the time I reach the top of the hill.👍
Bluevitz-rsOshawa, Ontario, Canada · Sep 12, 2010#28
Rob, you need a 1.5 in that thing
rob323Joyner, Brisbane · Sep 12, 2010#29
Yes, that's all fine but it throws me up into the 1401-1600cc class where there is no way I can compete against mivec mirages and Vtec civics.😉
Bluevitz-rsOshawa, Ontario, Canada · Sep 12, 2010#30
^ Oh, gotcha
why?harnett county NC · Sep 12, 2010#31
Originally Posted by Jason@SportsCar ↑
A 6spd would actually do the opposite. A 6spd is essentially a close-ratio gear box, and 6th gear is only fractionally taller than 5th in a 5spd. And in nearly every case Toyota has outfitted the 6spd with a shorter final drive, which actually means you are spinning the engine more with the 6spd.

If you want to drop your revs put on some taller tires, or drive slower. 😆
Well I knew a 6 speed would be closer ratio, but I hate the 4th to 5th gear change in the yaris, it is almost worthless. If the 6 speeds do have a shorter final drive, you would be right, and the last thing the yaris needs is to be revving even higher at normal highway speeds.

So if I ever have enough money or time I'd need to look outside of Toyota, and that would mean crazy money. Oh well.
Bluevitz-rsOshawa, Ontario, Canada · Sep 12, 2010#32
Just change out the fifth gear for the .725 in the C60/C160
johnny_vitzHamilton, Canada · Sep 12, 2010#33
Originally Posted by Tamago ↑
yes, the xa/xb/echo share transmission mounts. the echo trans is a bit longer, so a swap from an xB to echo would yield slightly more room on the end. the xB comes with an 8 bolt differential, so i'm not sure why you'd be concerned with using an 8 bolt lsd in your 8 bolt transaxle ?
The 8 bolt is just a lot more common and easier to find (than the echo's 6 bolt). I just wanted to make sure the xb trans would fit in so I could just have the xb trans with an LSD ready for spring to go in...👍 With a new clutch and flywheel. Thanks for the info!
47_MasoN_47Northwest Alabama · Sep 13, 2010#34
My biggest complaint about my Yaris gearing (automatic) is the 3rd gear. Mine accelerates fine in 1st and 2nd, then when 3rd comes along it's such a long gear that acceleration drops rapidly and people often start passing me. Also, it's annoying that sometimes the car will shift into 3rd when going uphill and then I'll actually start going slower until it figures out that it should have stayed in 2nd. I find myself manually shifting the gears when going uphill because of this. If I could have bought a manual to begin with I would have, but I could only find 1 manual sedan in the whole southeast (within my dealer's trading range) and it was as base model as you can get :(
TamagoOff Grid · Sep 13, 2010#35
Originally Posted by 47_MasoN_47 ↑
My biggest complaint about my Yaris gearing (automatic) is the 3rd gear. Mine accelerates fine in 1st and 2nd, then when 3rd comes along it's such a long gear that acceleration drops rapidly and people often start passing me. Also, it's annoying that sometimes the car will shift into 3rd when going uphill and then I'll actually start going slower until it figures out that it should have stayed in 2nd. I find myself manually shifting the gears when going uphill because of this. If I could have bought a manual to begin with I would have, but I could only find 1 manual sedan in the whole southeast (within my dealer's trading range) and it was as base model as you can get :(
that sounds like an engine problem to me ;) time for more power!
NinerOvid MI · Oct 22, 2010#36
If anyone's interested, I've got a Scion xA and want to do the reverse swap - put a Yaris final drive in it. I'm more interested in gas than speed. Used to have a Yaris but lost it in a garage fire (and just discovered I still have a login here).

Not sure how we'd work out the swap (I have a truck, but driving that for very long defeats the purpose of saving fuel). Any takers in Michigan near Lansing or Detroit would be a much better option, or anyone that has the engine out already and don't need the shaft back immediately (with escrow cash or whatever needed so I don't sit on my butt too long.)

Henry
2009BBPliftbackWestern PA (Franklin) · Oct 23, 2010#37
I used to own a stick first gen xb, and that is one thing i loved about it was the gearing. nice to know i can now have that in my yaris monster..🙂
TamagoOff Grid · Oct 23, 2010#38
Originally Posted by Niner ↑
If anyone's interested, I've got a Scion xA and want to do the reverse swap - put a Yaris final drive in it. I'm more interested in gas than speed. Used to have a Yaris but lost it in a garage fire (and just discovered I still have a login here).

Not sure how we'd work out the swap (I have a truck, but driving that for very long defeats the purpose of saving fuel). Any takers in Michigan near Lansing or Detroit would be a much better option, or anyone that has the engine out already and don't need the shaft back immediately (with escrow cash or whatever needed so I don't sit on my butt too long.)

Henry
buy an echo transmission, direct swap into the xA.

i know, because i've done it personally.
Bluevitz-rsOshawa, Ontario, Canada · Oct 23, 2010#39
I have a Echo transmission for sale. It's parts only though as it has a C160 bell housing bolted onto it to keep it all together. It's basically the leftovers from my 6 speed conversion. But there'd be no problem with swapping the guts into the xA transmission.

PM me if you're interested. Only asking $150CND plus shipping.
CrankyOldManWest Michigan · Aug 7, 2011#40
So after a read-through of the transmission repair manual, this is NOT something that a weekend DIY-er like myself should mess with--unless the have access to a large number of specialty tools and/or can afford to have their daily driver out of service for several days. I had contemplated buying a used tranny and pulling it apart, but the sheer number of SST's involved is intimidating.

In addition, the cheapest ones I can find locally are in the $350-400 range. It would almost seem to be more cost effective to just buy the new OEM output shaft and gear ring and have a shop put them on. By cost effective, I'm referring to the fact that you would then have a mostly useless transmission housing that won't fit on your engine. You could probably rebuild the donor tranny, but you would have to replace all of the seals and even then you'd be stuck with a final drive ratio that you didn't want in the first place.
Jason@SportsCarThread starterDebary, FL · Sep 6, 2012#41
Just bumping this with the latest part numbers, the output shaft was updated.
fnkngrvIn The Hotbox · Sep 6, 2012#42
This thread is a nice one to chew on, but leaves more confusion for me with this car as well as my unique goals especially when the OEM rev limiter is not actually allowing you to reach that tipping point where you "run out of gear".
Jason@SportsCarThread starterDebary, FL · Sep 6, 2012#43
Originally Posted by fnkngrv ↑
This thread is a nice one to chew on, but leaves more confusion for me with this car as well as my unique goals especially when the OEM rev limiter is not actually allowing you to reach that tipping point where you "run out of gear".
Then you need to fix your problem, and get past the OEM rev limiter. 🤷 How can you make a serious attempt at power gains without ECU control? It is not cheap, but there are solutions, and power to be had.
Flipper_1938Kentucky · Sep 6, 2012#44
Originally Posted by Jason@SportsCar ↑
Then you need to fix your problem, and get past the OEM rev limiter. 🤷 How can you make a serious attempt at power gains without ECU control? It is not cheap, but there are solutions, and power to be had.
What's the best way to do that?
cali yarisCanoga Park, CA · Sep 6, 2012#45
^ It's in his quote. ECU control.
Flipper_1938Kentucky · Sep 6, 2012#46
Originally Posted by cali yaris ↑
^ It's in his quote. ECU control.
That's what I'm asking....what is the best way to control the ECU? Can the stock ECU be hacked with some sort of tuner? or do you need a stand alone ECU?
fnkngrvIn The Hotbox · Sep 6, 2012#47
Originally Posted by Jason@SportsCar ↑
Then you need to fix your problem, and get past the OEM rev limiter. 🤷 How can you make a serious attempt at power gains without ECU control? It is not cheap, but there are solutions, and power to be had.
That's part of the plan, but I wouldn't dare to run up the rev limiter on a stock bottom end anyway at the speeds that I am attempting.
cali yarisCanoga Park, CA · Sep 6, 2012#48
Can the stock ECU be hacked with some sort of tuner? or do you need a stand alone ECU?
Standalone.
Jason@SportsCarThread starterDebary, FL · Sep 6, 2012#49
Originally Posted by fnkngrv ↑
That's part of the plan, but I wouldn't dare to run up the rev limiter on a stock bottom end anyway at the speeds that I am attempting.
I am 7300 all day long on a stock bottom end (rods/crank/pistons even valve springs). 🤷
Jason@SportsCarThread starterDebary, FL · Sep 6, 2012#50
Originally Posted by Flipper_1938 ↑
That's what I'm asking....what is the best way to control the ECU? Can the stock ECU be hacked with some sort of tuner? or do you need a stand alone ECU?
AEM EMS series 2, piggy-backed to the stock ECU (stock ECU does start up/idle/DBW, the AEM does the rest including VVT control).