I am looking for an aftermarket spring with the least drop, I don't want to put stock springs back... No control with stock springs ;d, I am thinking of putting NF210s? ARe there any that have less drop? Thanks.
Spring Question
20 posts · 7,568 views
Replies 19
Eibatch is only 1" drop.
U can do some research about TRD, 1.2' drop, gd enough for me. Mine run on stock shocks, still comfy enough.
NF210's are 1.1/1.2, that is less than the TRD springs, which are closer to a 1.5" drop.
The NF210's are less stiff, only 10% over stock (just to compensate for the shortened spring length)
The NF210's are less stiff, only 10% over stock (just to compensate for the shortened spring length)
^^ what he says...
http://www.tanabe-usa.com/nf210.asp?id=2
If you want something higher than that.. the why not just stay stock?
http://www.tanabe-usa.com/nf210.asp?id=2
If you want something higher than that.. the why not just stay stock?
dude, where have you been. PM me.Originally Posted by TheRealEnth ↑I am looking for an aftermarket spring with the least drop, I don't want to put stock springs back... No control with stock springs ;d, I am thinking of putting NF210s? ARe there any that have less drop? Thanks.
how much is it nf210 ? where can I get them .
You all should see the under of my car. Its so low, the frame is kinda bashed in. I have a Carbing front control arm bar that was hella bent after hitting a pot hole.
Picture not included in this copyThe bottom side of my car looks like that.
Picture not included in this copyThe bottom side of my car looks like that.
Megan Racing are just 1.5 and cheaper than the others. Check them on ebay...
i had eibach prokits on the car last winter....loved them, but not low enough for my taste...
with 205-55-15
Picture not included in this copy
on winter 185-60-14's
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
with 205-55-15
Picture not included in this copy
on winter 185-60-14's
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
how much is it nf210 ? where can I get them .in my store, here:
http://www.shop.microimageonline.com...ris-TNF210.htm
🙂
Don't mean to go slightly off-topic, but if you're looking for the best control without a big drop, you could just save a big buck and run stock springs with a rear sway bar. It's all it really needs.
trd rear sway bar ?Originally Posted by SilverBack ↑Don't mean to go slightly off-topic, but if you're looking for the best control without a big drop, you could just save a big buck and run stock springs with a rear sway bar. It's all it really needs.
Ultra Racing, 19mm same as TRD but less expensive, .or
23mm only from Ultra Racing
Both in stock!
23mm only from Ultra Racing
Both in stock!
what's the difference from 19mm and 23mm..Originally Posted by cali yaris ↑Ultra Racing, 19mm same as TRD but less expensive, .or
23mm only from Ultra Racing
Both in stock!
does 23mm handles better then 19mm.
is it easy to install. thanx
Easiest performance mod you could do to your Yaris. The 23mm is a bit thicker so it's going to tighten up things a bit more as far as handling goes (keeping the body roll flat). I'd say with the 23mm that while possible to do, have a friend on hand to help fit it on one side while you get the other. Mine anyways, was a very close fit for where you install it, so it helps to have another hand to line it up.
It's not hard to put on at all though. 4 bolts and your done! The difference it makes is quite surprising, especially the 23mm.
It's not hard to put on at all though. 4 bolts and your done! The difference it makes is quite surprising, especially the 23mm.
thanx , will be buying 23mm soon :)
Originally Posted by detroiter ↑Easiest performance mod you could do to your Yaris. The 23mm is a bit thicker so it's going to tighten up things a bit more as far as handling goes (keeping the body roll flat). I'd say with the 23mm that while possible to do, have a friend on hand to help fit it on one side while you get the other. Mine anyways, was a very close fit for where you install it, so it helps to have another hand to line it up.
It's not hard to put on at all though. 4 bolts and your done! The difference it makes is quite surprising, especially the 23mm.
custom coilover sleeves?
Originally Posted by ddongbap ↑You all should see the under of my car. Its so low, the frame is kinda bashed in. I have a Carbing front control arm bar that was hella bent after hitting a pot hole.
Picture not included in this copyThe bottom side of my car looks like that.
Too bad that r8 is in europe... and you're in socal... u mad brah?