Yarisworld Archive

MAF placement: upstream or downstream?

16 posts · 5,414 views

Bluevitz-rsOriginal postOshawa, Ontario, Canada · Jun 24, 2010#1
With any luck I'll be purchasing a Greddy Turbo kit for my Echo in a few weeks and was wondering if it's better to have the MAF upstream or downstream of the turbo. I'll be starting out with just the basic kit Stage 0, so no intercooler. Also this will most only be for DD use, but might see the occasional track day.

I guessing I should leave well enough alone and just leave the kit the way it comes, but was just wondering what people's opinions are.

Replies 15

cali yarisCanoga Park, CA · Jun 24, 2010#2
I think right before the TB is the usual placement. I have my MAP sensor there.
Bluevitz-rsThread starterOshawa, Ontario, Canada · Jun 24, 2010#3
That's what I was thinking too, but the Greddy kit uses the factory airbox, thus using the MAF before the turbo. Because I'm thinking, if I add a BOV (probably a recirculating type) air will be metered even after the throttle plate is closed causing a major rich condition.

In my head the proper placement would be just before the TB, but after the BOV, so when you close the throttle air stops being metered and exits through the BOV before getting to the MAF.
Nexus1155Dorchester · Jun 24, 2010#4
I see a lot of turbo kits having it on the inlet of the turbo, but i thought most ideally you would want it to meter air right before it went into the engine as where Garm says. Seems like you would get the most accurate reading of what is going into your engine at that location and that is quite important for the tune
Bluevitz-rsThread starterOshawa, Ontario, Canada · Jun 24, 2010#5
Originally Posted by Nexus1155 ↑
I see a lot of turbo kits having it on the inlet of the turbo, but i thought most ideally you would want it to meter air right before it went into the engine as where Garm says. Seems like you would get the most accurate reading of what is going into your engine at that location and that is quite important for the tune
Yeah, and on top of tuning, the ECU would also know what the intake temps are and would be able to control knocking and ignition advance more effectively.
lilredrocketDFW, Texas · Jun 24, 2010#6
Originally Posted by Nexus1155 ↑
I see a lot of turbo kits having it on the inlet of the turbo, but i thought most ideally you would want it to meter air right before it went into the engine as where Garm says. Seems like you would get the most accurate reading of what is going into your engine at that location and that is quite important for the tune
While this is great thinking. Why do both of the S/C kits for the Yaris have the MAF located before the S/C I understand with the Blitz you can't put in a MAF after the charge but with the PE kit the charge pipe runs right back by the MAF why didn't they put the MAF in the charged air?
Bluevitz-rsThread starterOshawa, Ontario, Canada · Jun 24, 2010#7
^ It's probably designed to use the stock airbox too. Therefore it would require the MAF to be located before the charge in the airbox.
Nexus1155Dorchester · Jun 24, 2010#8
Less risk of a CEL? lol
lilredrocketDFW, Texas · Jun 24, 2010#9
Actually the PE kit comes with a cone filter. You can only use their filter because the intake pipe has a flange/plate that the filter bolts to.
Bluevitz-rsThread starterOshawa, Ontario, Canada · Jun 25, 2010#10
Next question: would it be harmful in any way to the downpipe and manifold if I was to wrap it in header wrap?
cali yarisCanoga Park, CA · Jun 25, 2010#11
Part of my downpipe is wrapped -- helps cut down the heat near (and right under) the firewall in my case.

As for the manifold I sent mine off to Jet-Hot.
http://www.jet-hot.com/
Nexus1155Dorchester · Jun 25, 2010#12
http://www.techlinecoatingswebstore....o_X_Black.html

Only a thin layer needs to be sprayed, looks great, works great. Guy at our shop sprayed his manifolds and downpipes with some crappy HF canister gun and it came out excellent. Doesn't need to be a pro paint job :P but it layed out nice and even
Bluevitz-rsThread starterOshawa, Ontario, Canada · Jun 26, 2010#13
My concern is more about it possibly cracking do to the heat being kept in??? Or should that not be a concern with a cast manifold?
Nexus1155Dorchester · Jun 26, 2010#14
LOL doubt you need to worry with a manifold like this, nothing to it really, alot of cracking manifolds are from stress, The log really has no stressful areas as it is too short of a design and has no crazy woo doodley bends or long pipings
cali yarisCanoga Park, CA · Jun 26, 2010#15
doodley bends, ha, good one.

but yeah, if it cracks it's not because it kept the heat in.
Bluevitz-rsThread starterOshawa, Ontario, Canada · Jun 26, 2010#16
👍 Thanks guys!