kouOriginal postnj · Jun 20, 2010#1So i did the swap without getting a cel ever. THANK YOU jkuchta for the info.I ordered a new intake manifold, a yaris and a corrola throttle body.Step one was to fill in all the cavaties on the manifold with JB weld then port the opening as much as i could. swapped the chips over on the throttle bodies and removed the epoxy from the idle adjustment screw,then switched everthing over, did a pre adjustment on the idle screw and made a paper gasket which is siliconed in place.
7 attachments not included in this copy
Replies 52
thebarberGrand Rapids, MI · Jun 20, 2010#2how much were you able to open up the stock manifold?
kouThread starternj · Jun 20, 2010#3I ported the top to about 2.4" then i tappered down as much as i could, the plastic is thinner the further you go.the factory opening is 1.75".
thebarberGrand Rapids, MI · Jun 20, 2010#4not too shabby
notice a difference then?
tk-421Dagobah · Jun 20, 2010#5Nice and clean. Very good job! 👍
I opted for a custom adapter instead of porting the IM. How much did the IM cost? Just curious.
kouThread starternj · Jun 20, 2010#6There is a difference at all rpms but more after 2250rpms.more engine power with the ac on which is a big plus. my ASStermater says more tourqe than hp.definetly worth the $250 in total spent.
kouThread starternj · Jun 20, 2010#7 Originally Posted by
tk-421 ↑ Nice and clean. Very good job! 👍
I opted for a custom adapter instead of porting the IM. How much did the IM cost? Just curious.
Thanks tk-421.manifold cost $113
1NZYaris1New Zealand · Jun 20, 2010#8Wow that is nice🙇🙇🙇
this is one Mod i would love too do , but am affraid to do as it might not
be as simple on the 2NZ-FE.👎
Enjoy and congrates 👏👏
thebarberGrand Rapids, MI · Jun 20, 2010#9 Originally Posted by
1NZYaris1 ↑ Wow that is nice🙇🙇🙇
this is one Mod i would love too do , but am affraid to do as it might not
be as simple on the 2NZ-FE.👎
Enjoy and congrates 👏👏
should be the same...only different item on the 2nz is the pistons/rods (and therefore the displacement)?
kouThread starternj · Jun 20, 2010#10 Originally Posted by
1NZYaris1 ↑ Wow that is nice🙇🙇🙇
this is one Mod i would love too do , but am affraid to do as it might not
be as simple on the 2NZ-FE.👎
Enjoy and congrates 👏👏
Thanks i am enjoying ever minute.
cali yarisCanoga Park, CA · Jun 20, 2010#11nicely done. I've always thought that this mod, done carefully, is a good one.
kouThread starternj · Jun 20, 2010#12 Originally Posted by
cali yaris ↑ nicely done. I've always thought that this mod, done carefully, is a good one.
Thanks, definitely can't rush this one.
d1nzfeasia · Jun 21, 2010#13what do u fill up those 'holes' with? the purpose to 'strengthen' the frame for porting?
Nexus1155Dorchester · Jun 21, 2010#14NICE WORK, very good thinking on how to get it done, as long as you let the JBWeld cure and it stays that is a nice for DIYers. Just hope nothing ever happens where a chunk might come off of that and go into the engine
kouThread starternj · Jun 21, 2010#15Thanks Nexus.I am not to worried about the JB weld it's now a solid ring.Any way if something did happen engines are pretty cheap.
kouThread starternj · Jun 21, 2010#16 Originally Posted by
d1nzfe ↑ what do u fill up those 'holes' with? the purpose to 'strengthen' the frame for porting?
I used JBweld the slow curing type.Mainly to make a flat mating surface for the throttle body.Because of the intake manifold design after porting you have to put JBweld on the inside to get a smoother slope.
Nexus1155Dorchester · Jun 22, 2010#17Drive a full cycle, usually 80miles on most ECU's and let us know if there are any CEL then? I would love to do this.
YarisSedanCalifornia - Bay Area · Jun 22, 2010#18Wow very nice. If your gona do something do it right. For the price of the intake manifold its not that bad.
kouThread starternj · Jun 22, 2010#19No CEL after 2 days and half a tank of gas.
Only have high idle on cold start for 20-30 seconds then its all normal operation.
AstromanWenatchee, WA · Jun 23, 2010#20You would'nt happen to have any pics of the porting do you? I did the TB swap but just bolted on the new one w/o doing much else. (No CEL either.)
mario98cPuerto Rico · Jun 23, 2010#21Astroman do you use the corolla tb with the yaris tb chipor you use the corolla one?
tk-421Dagobah · Jun 23, 2010#22Both ways work. I have a 1ZZ TB with a 1NZ chip, no CEL. Just a high idle for the first 30 seconds or so.
mario98cPuerto Rico · Jun 23, 2010#23So all i have to do is put jbweld in all the openings of the intake manifold then make the chip swap then make the idle screw adjustment and install everything up? i am correct?
AstromanWenatchee, WA · Jun 24, 2010#24I used the corolla TB and chip. Bought mine from FunctionSpec. It had a different part number though than what everyone else seems to be able to find. Mine was off of a 05 Corolla, no chip swap or idle screw adjustment.
mario98cPuerto Rico · Jun 24, 2010#25Can you give me the part number if not too much trouble?
AstromanWenatchee, WA · Jun 24, 2010#26mario98cPuerto Rico · Jun 24, 2010#27Thanks Bro👍
AstromanWenatchee, WA · Jun 24, 2010#28Your welcome! Hope you get one, and if you do please post your findings and results.
mario98cPuerto Rico · Jun 24, 2010#29 Originally Posted by
Astroman ↑ Your welcome! Hope you get one, and if you do please post your findings and results.
ok. Not problem🎉
sitoSingapore · Jun 24, 2010#30 Originally Posted by
Astroman ↑
Astroman, did you experience abnormalities when the aircon kicks in?
While my car was stopping (with aircon on), i could feel jerking and my car moving forward even i stepped on my brakes..
And did you experience oscillations while driving?
I have the same throttlebody number as yours and have not done any chip swap or idling screw..
Going to try the chip swap soon.... 🙁
AstromanWenatchee, WA · Jun 24, 2010#31No I haven't noticed any abnormalities except at cold idle startup, but I've only used the A/C once or twice. Once it gets HOT here (which will be next month thru august) I'll check it out more.
sitoSingapore · Jun 25, 2010#32 Originally Posted by
Astroman ↑ No I haven't noticed any abnormalities except at cold idle startup, but I've only used the A/C once or twice. Once it gets HOT here (which will be next month thru august) I'll check it out more.
Thanks Astroman.... 😁
ParmasML · Jun 27, 2010#33 Originally Posted by
kou ↑ I ordered a new intake manifold, a yaris and a corrola throttle body.
Nice work mate enjoy your workmanship 👍
Is this the 1ZZFE throttle body?
kouThread starternj · Jun 29, 2010#34 Originally Posted by
Parmas ↑ Nice work mate enjoy your workmanship 👍
Is this the 1ZZFE throttle body?
Thank you, and yes it is the 1zzfe throttle body.
kouThread starternj · Jul 2, 2010#35So its has been a week and still going great.One cel/code popped up which was a p0171(bank 1 system lean.)This only happened once on a 95degree day with high humidity the AC on stuck in traffic,cel turned off on it's own the next day so i am sure its because of the conditions that day caused the cel.High humidity not good.
tk-421Dagobah · Jul 2, 2010#36 Originally Posted by
kou ↑ So its has been a week and still going great.One cel/code popped up which was a p0171(bank 1 system lean.)This only happened once on a 95degree day with high humidity the AC on stuck in traffic,cel turned off on it's own the next day so i am sure its because of the conditions that day caused the cel.
Did you do a coolant line bypass on the 1ZZ TB? I did, and I've literally never had a CEL with my TB.
Although it may not be advisable under very cold weather for what I hear (we don't get too many of those down here)...
kouThread starternj · Jul 2, 2010#37 Originally Posted by
tk-421 ↑ Did you do a coolant line bypass on the 1ZZ TB?
Yes i did,i am thinking about putting it back in the fall.
kouThread starternj · Jul 2, 2010#38I have had this code before with the stock setup so i am not to concerned.
sitoSingapore · Jul 3, 2010#39 Originally Posted by
kou ↑ So its has been a week and still going great.One cel/code popped up which was a p0171(bank 1 system lean.)This only happened once on a 95degree day with high humidity the AC on stuck in traffic,cel turned off on it's own the next day so i am sure its because of the conditions that day caused the cel.High humidity not good.
Kou, i also have the same symptom as yours. AC on, stuck in traffic, CEL on. But my error is p0172(bank 1 rich). CEL went off on its own on the next day.
Now still monitoring what causes this CEL. 😕
moh-6.304976,106.765952 · Jul 3, 2010#40i got a TB with part number #22030-0D030 and want to install it next week.
should i do chip swap and idle screw adjustment? and what about coolant bypass?
AstromanWenatchee, WA · Jul 3, 2010#41 Originally Posted by
moh ↑ i got a TB with part number #22030-0D030 and want to install it next week.
should i do chip swap and idle screw adjustment? and what about coolant bypass?
Just try swapping over first like I did. Didn't need to do a chip swap or idle screw adjustment.
I didn't do the coolant bypass because it can get pretty cold where I live and I don't want any issues. Car works awesome with it hooked up.
sitoSingapore · Jul 8, 2010#42Hi Guys,
I had swapped my 1NZFE chip into the 1ZZFE throttle body but after one day of driving... CEL light up.. error code 0172 (fuel trim too rich bank 1)
I reset my ecu, and drove again... and the next day... the same error code came out.... 🙁
These two codes came when i was moving off slowly and with air con on.
I swapped the 1ZZFE chip (part number #22030-0D030) back onto the throttle body and there's no CEL till now. But i could feel rpm oscillations when car was slowing down. By adjusting the idling screw, does it helps to remove the oscillations?
Should i stick to 1ZZFE chip or try making the 1NZFE chip works? 😕
Thanks everyone! 🙂
sitoSingapore · Jul 8, 2010#43Any advice, please?
Thanks... 🙂
tk-421Dagobah · Jul 9, 2010#44 Originally Posted by
sito ↑ Should i stick to 1ZZFE chip or try making the 1NZFE chip works? 😕
Leave the 1NZ chip in. That's the way I have it and it works great.
sitoSingapore · Jul 9, 2010#45 Originally Posted by
tk-421 ↑ Leave the 1ZZ chip in. That's the way I have it and it works great.
Thanks for your advice, tk-421. 😁
Are you using the 1ZZFE chip with the 1ZZFE throttle body too?
Thanks....🙂
tk-421Dagobah · Jul 9, 2010#46Sorry, I meant to say to leave the 1NZ chip on the 1ZZ TB. I made the swap and I haven't had any issues so far, other that a high idle when cold starting the car.
On the other hand, I've heard from some people that didn't need to swap the chip at all (1zz chip on 1zz TB). I have a theory that the issue is directly related to the TB serial number, but I can't say for sure. I tried compiling a list of serials a few months ago, but it didn't catch on. 🤷
sitoSingapore · Jul 9, 2010#47 Originally Posted by
tk-421 ↑ Sorry, I meant to say to leave the 1NZ chip on the 1ZZ TB. I made the swap and I haven't had any issues so far, other that a high idle when cold starting the car.
On the other hand, I've heard from some people that didn't need to swap the chip at all (1zz chip on 1zz TB). I have a theory that the issue is directly related to the TB serial number, but I can't say for sure. I tried compiling a list of serials a few months ago, but it didn't catch on. 🤷
Thanks for the advice,tk-421...😁
With your 1NZ chip on the 1ZZ TB, did you experience any jerking (around 1300rpm) while you were driving?
Did you adjust your idling screw? How many turns did you adjust? Anti-clockwise?
Thanks in advance, tk-421...🙂
kouThread starternj · Jul 16, 2010#48Still running great no CEL.
tk-421Dagobah · Jul 17, 2010#49 Originally Posted by
sito ↑ Thanks for the advice,tk-421...😁
Don't mention it. 👍
With your 1NZ chip on the 1ZZ TB, did you experience any jerking (around 1300rpm) while you were driving?
The bigger TB will increase your overall throttle response. There's a bit on an adjustment required on your part (basically, one needs to be less hard on the pedal). Although to be honest, the throttle controller that I have installed makes that effect much more apparent.
Did you adjust your idling screw? How many turns did you adjust? Anti-clockwise?
I can't remember right now, but I believe it was more to the right (CW) than the left (CCW), but it really should depend on your particular installation. You can adjust it while the engine is on, but don't trust it too much... The ECU will also try to auto-adjust over the next few days. If you don't feel that it's perfect you can always try adjusting it further. Just be careful not to strip the screw! 😳
sitoSingapore · Jul 26, 2010#50 Originally Posted by
tk-421 ↑ Don't mention it. 👍
The bigger TB will increase your overall throttle response. There's a bit on an adjustment required on your part (basically, one needs to be less hard on the pedal). Although to be honest, the throttle controller that I have installed makes that effect much more apparent.
I can't remember right now, but I believe it was more to the right (CW) than the left (CCW), but it really should depend on your particular installation. You can adjust it while the engine is on, but don't trust it too much... The ECU will also try to auto-adjust over the next few days. If you don't feel that it's perfect you can always try adjusting it further. Just be careful not to strip the screw! 😳
Thanks for the advice, tk-421.... 😁