HersheyOriginal postnortheast · Jun 9, 2010#1here's pic . Very similar to the '08 sedan we have . They put dye in this engine as well. Bring it back to dealer in a few weeks. Will keep posted.
Replies 85
HersheyThread starternortheast · Jun 11, 2010#2used a mirror and a flashlight to get a look at the upper back part of the timing chain seal for the 2010 and 2008 to find the seal leaking just above the large ledge in the corner that's part of the block . It was wet with a sheen of oil and felt slippery on the tip of my finger . Could see some dye in that area with a blacklight on the 2008 sedan . Quite sure it's not the head gasket for either YARIS . I can see how this leak could easily be overlooked . Will try to get a clear picture of that area that's on both . Plan to switch from the 5w-30 synthetic that's used for both to a conventional motor oil to see what occurs .
Yaris HiltonBristol, Tennessee, USA · Jun 12, 2010#3I thought a head gasket was an unlikely source of an oil leak alone. Usually the main problem with that is gas from the combustion chambers leaking into the cooling jackets, followed by coolant being sucked into the chambers.
TheSilkySmoothNew Hampshire · Jun 13, 2010#4I have some weeping around that area too. Remeber "everyone" will tell ya modern synthetics dont "cause" leaks.
HersheyThread starternortheast · Jun 14, 2010#5this is from the 2008 sedan . The area circled in red is the sealant for the backside of the timing chain cover that is most likely the source of the leak for the '08 and 2010 3 door . Cleaned this area that was wet with fresh oil and could see some dye with the blacklight . It also had a sheen to it with a regular flashlight . Plan to recheck it in a week or so for both cars and clean it again . Then after that plan to dump the SHELL Full synthetic 5w-30 and replace with SHELL conventional 5w-30 and do a short run of about 2,500 miles to get rid of more dye along with synthetic that's left behind in the '08 . Then again refill with SHELL conventional to see if the leak stops or slows down . Will do the same for the 2010 at a later date . Hopefully this will do the trick . If not , will take pics to a different dealer to get the leaks repaired 🙁 .
1stToyotaOklahoma · Jun 15, 2010#6Just checked that area on mine...a little discoloration and buildup there, but doesn't look wet at all, and I've used synthetic in all but one oil change since new. Maybe it's just an area that's prone to leak if it's not sealed properly with RTV when the motor is assembled. If it's leaking at the front cover the RTV shouldn't really be effected by the oil being synthetic or conventional.
HersheyThread starternortheast · Jun 15, 2010#7rechecked the 2008 last night and it's getting wet again . Going to dump the syn and dye with conventional before the weekend .
HersheyThread starternortheast · Jun 19, 2010#8checked it again this evening after little less than a week . The seal and the upper / underside of ledge are wet with oil again after cleaning that area . The blacklight showed green ( engine dye ) around the seal . Drained the synthetic with the dye out of the '08 sedan earlier and replaced with conventional SHELL 5w-30 . Recleaned the area again . Plan to do a short run of that to get most / all of the synthetic and leftover dye out . Then stay with the conventional SHELL 5w-30 to see if the leak slows or stops . Hopefully the myth of synthetics causing leaks to be the case and somehow the conventional will put the seeping to an end . Will do the same with the 2010 3 door . Time will tell .
1stToyotaOklahoma · Jun 19, 2010#9Good luck & hope you see a difference, but if the leak is at the front cover where the RTV sealant is I can't imagine synthetic being able to seep through but conventional oil not.
But just in case, I'm due an oil change, so for s&g I'll be using regular 5w30, and if it does good I'll probably stick with it and stop using synthetic also, but not because I'm experiencing any leaks now, because it'll save me money, plus I stick to 5k OCIs.
HersheyThread starternortheast · Jun 21, 2010#10Thanks . Just changed oil from SHELL 5w-30 Full Synthetic to SHELL 5w-30 conventional to rid of most of the syn and the dye . Checked and cleaned all areas that gather oil from the leaky seal . Will drain it again in 1,500 > 2,000 miles and then once more in the mid to late fall using SHELL or PENNZOIL 5w-30 convental . No more syns for awhile , if ever . Will keep eye on leak ( including the '08 sedan ) and hope for the best . Didn't realize the 3 door already has 7,400 miles not 6,600 . She drives it most of time . Sneaks up on yeh .
frog13Ohio · Jun 26, 2010#11First off,I'm not a mechanic/tech.I do however,ride DS bikes and have researched this very "thang" in regards to bikes.If your engine is new,has low miles and you do not have alot of run time,I'd say there is a torque issue or an improperly installed "gasket".Synthetics usually don't show leaks unless they are put in older vehicles.The older vehicles were more than likely using conventional oil for the majority of their service life,then the owner...for reasons unknown...decided to switch to synthetic.During the time the conventional oil was used...and yes,that's ok if you keep up with oil changes!!!....deposits build along the gasket "line".Now,add-in,during this time there was also blow-by fuel mixing in with the oil and engaging the gaskets...causing deterioation and overtime the conventional oil deposit were "filling-in" those micro-increasing gaps!.Synthetic oil is now introduced.This oil,which "cleans" better/more effectively and has MUCH better flow charateristics...is now removing all those years of deposits and the leaks begin to appear. The idea,I've read,is to begin using synthetic oil as soon as your engine is "broke-in"......then you won't have---as quick of gasket break-down as you did with the years of conventional use.👍
HersheyThread starternortheast · Jun 26, 2010#12both YARIS now have SHELL conventional 5w-30 . Will be draining these fills in 1,500 > 2,000 miles . Then another for both in late fall and run until MARCH or early APRIL of 2011 . Will post results as time flies by .
HersheyThread starternortheast · Jul 2, 2010#13checked for leak on the 2010 and was slighty wet with 539 miles on the oil change of SHELL conventional 5w-30 . Recleand the whole area . So , it seems to have slowed down with the conventional . Figure there's still a 1/2 quart or a bit more of the synthetic still in it . Will be doing another oil change soon with the SHELL 5w-30 to get rid of the syn that's left .
HersheyThread starternortheast · Jul 5, 2010#14decided to drain oil earlier with 569 miles on previous oil change and replaced with SHELL 5w-30 conventional along with another TOYO oil filter . There was still plenty of engine dye in the extracted oil . Wanted to get rid of the synthetic left behind so is mostly conventional oil . Took an empty 4 gallon jug of motor oil to measure the drained oil from the oil pan and oil filter . The oil was slightly over the 3 quart mark . Thus over 3/4s' of a quart must remain in the engine . I use 3 quarts and 22 ounces to get the to the FULL mark . This includes close to 6 ounces poured into the new oil filter before installation . Recleaned area where oil leaks and collects . Next oil change for both YARII won't be until late OCTOBER to early NOVEMBER . Will inspect in between . Hoping the leaks will start to slow or stop with the use of conventional . Time will tell all .
127.0.0.1NE · Jul 5, 2010#15 Originally Posted by
Hershey ↑ decided to drain oil earlier with 569 miles on previous oil change and replaced with SHELL 5w-30 conventional along with another TOYO oil filter . There was still plenty of engine dye in the extracted oil . Wanted to get rid of the synthetic left behind so is mostly conventional oil . Took an empty 4 gallon jug of motor oil to measure the drained oil from the oil pan and oil filter . The oil was slightly over the 3 quart mark . Thus over 3/4s' of a quart must remain in the engine . I use 3 quarts and 22 ounces to get the to the FULL mark . This includes close to 6 ounces poured into the new oil filter before installation . Recleaned area where oil leaks and collects . Next oil change for both YARII won't be until late OCTOBER to early NOVEMBER . Will inspect in between . Hoping the leaks will start to slow or stop with the use of conventional . Time will tell all .
an oil leak is an oil leak
changing the type of oil won't do any good
have it repaired properly
HersheyThread starternortheast · Jul 5, 2010#16worth a shot . If not , will get it repaired under warranty .
HersheyThread starternortheast · Jul 7, 2010#17well it's official we have a head gasket leak for the 2008 and 2010 . Decided to put the '08 sedan on the ramps and crawl under to look for oil and discovered a small drop on the 1st small ledge under the large lip ( pictured above ) after 2 days of driving in the extreme heat . Cleaned that off and took a look at the seal again to find it dry and no oil residue on tip of finger . Then I took another look with the flashlight at a different angle and noticed a sheen from the plastic head gasket that's sits further in ( cavern like ) above the large lip . Got out from under the car and reached in back of the engine and ran finger in that area to find plenty of fresh oil . The oil that leaks from it must reach the timing chain seal ( pictured above ) and makes that wet with oil and runs down under the the large lip ( pic above ) making me think it was the sealant all along . So the mechanic was right about the head gasket leak , but not from where he pointed out to be the " ball bearing " within the block below the large lip ( picture of that under the topic " WHAT'S THIS " ? ) . Then I decided to look at the 2010 3 door and that too was wet with oil in the same spot . Thus that has the plastic head gasket leaking as well . Talk about sh*t for luck . Will have to get both corrected under warranty . Not looking forward to that moment . Meantime will keep close eye on the leaks and the level of the coolant in both ( no change as off yet ) .
HersheyThread starternortheast · Jul 7, 2010#18could starting both cars out with synthetic motor oil at 1,500 miles be the culprit ? 🤷 . Just seems odd that both have the same leak and are a few years apart . Can't think of any other reason .
Lucas13Fort Lauderdale · Jul 8, 2010#19Have you ever flushed the engince with some product?
HersheyThread starternortheast · Jul 8, 2010#20nope , neither one .
HersheyThread starternortheast · Jul 8, 2010#212008 nearing 22,000 mis. and 2010 around 7,300 .
frog13Ohio · Jul 8, 2010#22I'm not arguing with anyone...but,synthetic motoroil WILL find faulty/faultering gaskets/seals!.I'm not debating a vehicles mileage or service records or the owners ability to do them...........synthetic has FAR superior flow characteristics,shear stability etc.At least try switching to a conventional motoroil and see what the result is.🙂
1stToyotaOklahoma · Jul 8, 2010#23He's already tried that...and I doubt that the oil was the reason for the failed head gasket. A seal maybe, in a neglected motor, but not a head gasket in a well maintained low mileage vehicle.
edit... oops, I re-read and saw where your indicated faulty gaskets
HersheyThread starternortheast · Jul 8, 2010#24this is a picture of where the head gaskets are leaking in both YARII circled in RED . This is taken from the 2010 3 door . The area circled in BLUE is the sealant for the tiiming chain cover that I thought was leaking . The area in RED is where the plastic head gasket is located on top of the cavern of the block that's found above the large ledge . The oil seeps from underneath and runs along the edge of the block / exposed head gasket ( in left side of RED circle ) and down to the sealant in BLUE . Then that runs under the large ledge and down the corner of the block that's pictured in the thread " Noticed possible oil leak " on page 2 and then scroll down to POST # 29 (
Noticed possible oil leak ... ) to see the bottom of the large ledge where oil collects on the 2010 .
Red HorseCosta mesa, California · Jul 8, 2010#25This thread should be in a history of yarisworld, Hershey just confirm that the using conventional oil is more restrictive than syntetic.
HersheyThread starternortheast · Jul 8, 2010#26both have had 2 oil changes with SHELL 5w-30 conventional oil in a months time and around 600 > 800 miles for both oil changes for each YARIS . So , maybe it's too soon for seepage to slow or stop with the conventional . 🤷 . Will keep track of it . No improvement , then off to the service center for both YARISes . 👎
HersheyThread starternortheast · Jul 8, 2010#27I suggest that those who started to use a synthetic early in the break in period or later take a good look for this . Those who use conventional may want to do the same . Many might not be aware of it . Especially those who get their oil changed by someone else . Would think there are some out there with this issue . I didn't notice it on the 2008 ( bought new ) until this past spring and I do all the oil changes for both cars . It's easy to overlook .
HersheyThread starternortheast · Jul 8, 2010#28TOYOTA . Oh , what a feeling !!! 😢 . More like the feeling you get when you get your prostate exam . 😲
sleey0PA · Jul 11, 2010#29So, the big question is:
Is this a common issue? Anyone else have leaks? Please share.
HersheyThread starternortheast · Jul 11, 2010#30it's not an easy leak to spot . As pictured above .
Lucas13Fort Lauderdale · Jul 23, 2010#31While I was taking care of the tension of my drive belt I decided to do a good inspection of the head gasket with a mirror and guess what...surprise!!! I found a small leak by the timing chaing side on the head cover gasket,I was able to see the dust trapped in the oil, the leak is also behind the alternator on that tiny courner.
Folks that use conventional oil should also take a look at this, this shouldnt happen so soon, normally the gasket that starts leaking first is the valve cover one, but the head gasket??? wow!!!
sleey0PA · Jul 23, 2010#32I see these pics and maybe it's just me but I am not seeing a huge problem here.
I dunno. Looks pretty insignificant to me.
HersheyThread starternortheast · Jul 23, 2010#33 Originally Posted by
sleey0 ↑ I see these pics and maybe it's just me but I am not seeing a huge problem here.
I dunno. Looks pretty insignificant to me.
this is because these areas have been cleaned before the pictures were taken . They're are photos with oil collected underneath the leak for both YARIS .
HersheyThread starternortheast · Jul 24, 2010#34These are from the '08 which has 23,000+ miles and leaks more . The 2010 seems to have slowed down . 1st pic is where the oil leaks from the plastic head gasket above the large ledge and collects underneath it . Have found it to run along seal of timing chain cover and end up on the upper lip of the oil pan . Not all that significant . The 2nd pic is the top of the ledge . The area circled in RED is where the plastic head gasket is hidden under the upper head . The last pic is a close up of the plastic head gasket that leaks for both ( sorry a bit blurred ) . The '08 sedan gets wet with oil every 100 miles or more , while the 2010 hasn't with same miles as of recent.
Lucas13Fort Lauderdale · Jul 24, 2010#35I cleaned the rear side I will keep the eye on it 😲
127.0.0.1NE · Jul 24, 2010#36an oil leak is a true fire hazard. it must be fixed. most cars fires
are from oil leak buildup.
oil leak....fixed. done.
HersheyThread starternortheast · Jul 24, 2010#37I'll possibly get to it after a few more oil changes with conventional engine oil . The 2010 seems to have stopped leaking with 2 conventinional O.C.s . Took it over 160 miles earlier in 90 degree heat . Did a quick check not long after we arrived home and nothing far as I can tell . Will do a more thorough inspection tomorrow . Keep our fingers crossed . So , 127.0.0.1 you'll need to be more patient .
127.0.0.1NE · Jul 25, 2010#38 Originally Posted by
Hershey ↑ I'll possibly get to it after a few more oil changes with conventional engine oil . The 2010 seems to have stopped leaking with 2 conventinional O.C.s . Took it over 160 miles earlier in 90 degree heat . Did a quick check not long after we arrived home and nothing far as I can tell . Will do a more thorough inspection tomorrow . Keep our fingers crossed . So , 127.0.0.1 you'll need to be more patient .
no, you can't fix an oil leak on a car by changing the oil, you can
only, perhaps, mask the problem. the problem remains
you need to repair a seal or gasket
there are no -liquid engine repair kits-
HersheyThread starternortheast · Jul 25, 2010#39we'll see .
pennyracergrants pass · Jul 25, 2010#40drain plug is leaking is my guess did you put a new drain bolt gasket on the drain bolt after you drained the oil ? all stop leak products a a bigger problem after you use it just like 127.0.0.1 is saying i fix the problem never will use half assed stop leak products in anything motor or tansmission of mine good luck with your oil leak should be a simple fix is my guess
HersheyThread starternortheast · Jul 25, 2010#41yes , always use a washer for the drain plug . There are pics of the leak . It's the plastic head gasket . Not a simple fix , quite a task . Don't use stop leak products . Would most likely void the warranty . Have been doing oil changes and working on cars ( nothing major ) for over 25 years .
pennyracergrants pass · Jul 25, 2010#42do you mean under the black motor cover ? that comes off with to nuts then the valve cover is exposed just seems odd a 2010 springing a leak so eary on but it can happen to any new car
pennyracergrants pass · Jul 25, 2010#43looks like a valve cover leak maybe
HersheyThread starternortheast · Jul 26, 2010#44Nope . Head gasket . For 2008 and 2010 . Located the leak for both .
127.0.0.1NE · Jul 26, 2010#45 Originally Posted by
Hershey ↑ yes , always use a washer for the drain plug . There are pics of the leak . It's the plastic head gasket . Not a simple fix , quite a task . Don't use stop leak products . Would most likely void the warranty . Have been doing oil changes and working on cars ( nothing major ) for over 25 years .
I know just a wee bit about how gaskets function and you can't
fix a head gasket with prayer-in-a-can.
1stToyotaOklahoma · Jul 26, 2010#46When did they start making plastic head gaskets? I've seen lots of plastic gaskets, including plastic intake gaskets, but that's a new one for me.
HersheyThread starternortheast · Jul 26, 2010#47Don't know . But I know hard black plastic when I see it .
1stToyotaOklahoma · Jul 26, 2010#48Napa's import line (Altrom) gasket for our Yaris looks to be layered steel with a coating on it; pretty typical for most.
Picture lost · partimages.genpt.com
I don't think plastic, even if it's reinforced around the combustion areas would take the heat, but I've been wrong before.
CTScottUSA, CT · Jul 26, 2010#49 Originally Posted by
1stToyota ↑ Napa's import line (Altrom) gasket for our Yaris looks to be layered steel with a coating on it; pretty typical for most.
Picture lost · partimages.genpt.com
I don't think plastic, even if it's reinforced around the combustion areas would take the heat, but I've been wrong before.
It is definitely an MLS (multi-layer steel) head gasket.
HersheyThread starternortheast · Jul 27, 2010#50Thanks . That's it . Looks to be a smooth plastic coating . The leak is from the lower right corner of the gasket close to the timing chain . The area circled in BLUE is where the leak comes from both '08 and 2010 . The exposed part of the gasket runs under the upper head . Wouldn't know it was steel by looking and touching it . I'll call someone to find out if it's all plastic or plastic coated steel or other coating.