Yarisworld Archive

Engine Speed Sensor Location?

23 posts · 41,445 views

H3LlIoNOriginal postMidatlantic · Jun 4, 2010#1
Where is it? I'm talking about the RPM sensor that send the speed data to the ECU...Or even better, does any one have a map of all of the sensor locations on a 1nz? thanks,

- H

Replies 22

Bluevitz-rsOshawa, Ontario, Canada · Jun 4, 2010#2
It's under the backside of the pulley. Look for a big black connector with tape on it.
ddongbaphay · Jun 11, 2010#3
Originally Posted by tech101 ↑
I am a new member here. But pls visit our homepage URL through my Signature and URL Link....
I tried. Why did i see porno?
tomatoSan Francisco Bay Area · Jun 11, 2010#4
sorry, better luck next time !
H3LlIoNThread starterMidatlantic · Jun 11, 2010#5
Thanks Cdy...here is the info for the next guy:

"The Crankshaft Position (CKP) sensor system consists of a CKP sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates and, as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the fuel injection time and ignition timing are controlled."

And location:

Picture not included in this copy
ParmasML · Jun 11, 2010#6
Originally Posted by H3LlIoN ↑
Thanks Cdy...here is the info for the next guy:

"The Crankshaft Position (CKP) sensor system consists of a CKP sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates and, as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the fuel injection time and ignition timing are controlled."

And location:

Picture not included in this copy

Does this sensor relates to the Crank Trigger?

Does the crank trigger is 34 on our 1NZFE?
H3LlIoNThread starterMidatlantic · Jun 11, 2010#7
I think you mean:

A) Is this the sensor same as a crank trigger? (yes)

B) Is the signal 34 pulses per revolution? (yes)
ParmasML · Jun 16, 2010#8
I don't know maybe the image is illusrated wrong since mine the crank sensor is at the lower left of the engine and not in the middle as shows the image.

See below attachment

Can you confirm is the same sensor?

1 attachment not included in this copy

Bluevitz-rsOshawa, Ontario, Canada · Jun 16, 2010#9
You're view the image in the wrong contexts. The view shows the sensor by looking through the motor and is indeed in the lower left corner of the block.
ParmasML · Jun 16, 2010#10
Thanks better sure than disappointed 👍
H3LlIoNThread starterMidatlantic · Jun 16, 2010#11
Sry I'm just getting to this...Bluevitz is correct. You need to be thinking in terms of X-ray vision.
ali077Mauritius · Aug 18, 2010#12
i need to connect a vehicle dynamic processor from pioneer. which of these sensors can i get the vehicle speed signal from?
Bluevitz-rsOshawa, Ontario, Canada · Aug 18, 2010#13
The Vehicle speed sensor comes out'a the transmission.
Zamal7591Mauritius · Aug 19, 2010#14
May I know what is the colour of the wire and where it si found exactly( Diagram or picture please)
Bluevitz-rsOshawa, Ontario, Canada · Aug 19, 2010#15
I replied to your PM, what year is the car?
Zamal7591Mauritius · Aug 19, 2010#16
its a 2003 Vitz TRD Turbo
Bluevitz-rsOshawa, Ontario, Canada · Aug 19, 2010#17
No need for the PMs...

It's a purple wire, but I don't have my EWD on hand to tell you what connector... I'll see If I can find it.

Edit: ok found it. I have a '04 manual, so as long as you have a 4 connector ECU it should be the same. It's a purple wire with white tracer, pin 17, connector B.
Zamal7591Mauritius · Aug 19, 2010#18
I'll try to check it tomorrow , Thanks!!! the ECU is 1 NZFE T , Do you think its the same!!!
Zamal7591Mauritius · Aug 19, 2010#19
I'll check it , Thanks , Do u think its the same as the ECU 1 NZFE T????
Bluevitz-rsOshawa, Ontario, Canada · Aug 19, 2010#20
Should be.
Zamal7591Mauritius · Aug 19, 2010#21
Btw can i get a picture of it , please?!!!

Or a plan?!!!
ali077Mauritius · Aug 19, 2010#22
but the arrangement of the wires on my ECU is completely different as mine is a turbo. its the same 1nz-fe engine but with factory fitted turbo. the code of my ecu is 1nz-fet. its does have 4 connector and does have a purple wire with white tracer but not in connector b and pin 17 as stated. shall ill try to connect it to the wire though?
btw thx for ure help. much appreciated.


Originally Posted by Bluevitz-rs ↑
No need for the PMs...

It's a purple wire, but I don't have my EWD on hand to tell you what connector... I'll see If I can find it.

Edit: ok found it. I have a '04 manual, so as long as you have a 4 connector ECU it should be the same. It's a purple wire with white tracer, pin 17, connector B.
Bluevitz-rsOshawa, Ontario, Canada · Aug 19, 2010#23
On my EWD, it's the only purple with white tracer on the ECU, so if that's the only one on yours, then it would be safe to assume it's the same.