Yarisworld Archive

Installed HID, Cracking in stereo

15 posts · 6,232 views

ArkhangelOriginal postPuerto Rico · May 24, 2010#1
Hey guys and gals its been a while

Installed HID in my headlights and Fogs, wired per diagram. the fogs are wired to the Accessories. when i hit the high beams theres a cracking in the sound system, and at times with the fogs. also for some reason when i hit the High beams my zune reboots. the zune isnt wired to any power of the car just plugged into the Aux Port.. Any ideas??

Replies 14

bzinn 1University Place,WA · May 24, 2010#2
do you have a relay for the HIDs or were they just plug into stock harness with the ballast,mine on my tC caused interferance as well till I put in a relay to isolate the ballast from the rest of electrical system......it was super annoying.

there is a guy on Scionlife named operatic that sells the relay harness for cheap,it might help.
CTScottUSA, CT · May 25, 2010#3
Can you scan and post the wiring instructions? With the Zune rebooting, it sound like you might be getting a high voltage pulse on the ground from the ballasts.
ArkhangelThread starterPuerto Rico · May 25, 2010#4
The kit just plugs right into the stock harness so i dont think it has a relay

Basically here is the wiring diagram

Picture not included in this copy
ArkhangelThread starterPuerto Rico · May 25, 2010#5
I would try to make my own harness with relay just need to know what kind of relay
CTScottUSA, CT · May 25, 2010#6
Originally Posted by Arkhangel ↑
The kit just plugs right into the stock harness so i dont think it has a relay

Basically here is the wiring diagram

Picture not included in this copy
I don't think that the relay method would help, as you will still be injecting the EMI/RFI from the ballasts into the system. The typical purpose of the HID relay harnesses is to bypass DRL module or to provide a direct supply from the battery for cars where the headlight circuit doesn't have the ampacity required by the ballast.

Cheap ballasts (cheaply made, not necessarily cheaply priced) lack an EMI filter. You can make your own with a couple of capacitors. I would try a 4.7uF and a 22,000 pF between the red and black power wires for the ballast. If the 4.7uF is a polarized electrolytic, make sure that the polarity indicator points the correct way (i.e. usually the negative side is marked with an arrow with minus signs on it - Make sure that that leg is connected to the black wire). The two capacitors get connected in parallel with each other, so both go between the red and black wires.
ArkhangelThread starterPuerto Rico · May 25, 2010#7
i need a diagram lol for that
CTScottUSA, CT · May 25, 2010#8
Originally Posted by Arkhangel ↑
i need a diagram lol for that

Make sure that the capacitors are rated for at least 25V.

Picture not included in this copy

1 attachment not included in this copy

ArkhangelThread starterPuerto Rico · May 25, 2010#9
thanx man, hmm lol how accurate are you on the numbers ?? i would have to make 4 sets right?
CTScottUSA, CT · May 25, 2010#11
Originally Posted by Arkhangel ↑
You will need one set per ballast. The values are best guesses, based on what I've seen for values in schematics of ballasts.

The first one is fine. The second was 22,000 pf (or .22 uF). From Radio Shack, I would try these:

http://www.radioshack.com/product/in...uctId=2102589#
ArkhangelThread starterPuerto Rico · May 25, 2010#12
gotcha Thank you again will stop at Radio Shack after work
ArkhangelThread starterPuerto Rico · May 25, 2010#13
BTW im guessing this set up is just to deal wit the crackling, any ideas why using high beams reboots the zune?
bobolinkoWas Hawaii - Moved to Everett WA · Jun 9, 2010#14
Turn on the Zune, and do not connect it to the Aux Port. See if the Zune reboots when you hit the High beams. Lemme know what hapns...

This might help to prevent the HF radiating back to the power supply in the vehicle...
One per Ballast (if the zune reboots without connecting)

http://www.radioshack.com/product/in...ductId=2103222
ArkhangelThread starterPuerto Rico · Jun 9, 2010#15
thanx man