Yarisworld Archive

splitter: made it myself

20 posts · 6,707 views

cali yarisOriginal postCanoga Park, CA · May 5, 2010#1
24" x 96" ABS plastic $75
roll of plastic door trim $10
APR stainless splitter supports $60
screws, rear straps etc $5
labor

rough cut with a Dremel nibbler, shaped with a flat file. self tapping screws underneath, and two rear metal straps to to hold the back rigid. It's about 16" deep.

Picture not included in this copy

Replies 19

severous01SE Texas · May 5, 2010#2
nice. all except the sheetmetal screws...i'd have used push pins or tape. but nice either way. you got under-body pic?
cali yarisThread starterCanoga Park, CA · May 5, 2010#3
all except the sheetmetal screws...i'd have used push pins or tape.
to attach it to the bumper? I don't think that would be secure.
coffiendOmaha, NE · May 5, 2010#4
Oh mannnn that looks nice. Good job!

DIY ftw
MUSKOKA800Chatham, Ontario, Canada · May 5, 2010#5
Looks great!

Get ready for the orders.
heeroyuy01195Florida · May 5, 2010#6
Originally Posted by severous01 ↑
nice. all except the sheetmetal screws...i'd have used push pins or tape. but nice either way. you got under-body pic?
that wouldn't hold it on very well, especially at higher speeds.
schleppyBoston, MA · May 5, 2010#7
Now make one that doesn't require strut supports and sell it to us!
yaris-meAnaheim, CA · May 5, 2010#8
I think you're ready to give NASCAR a run.
suckerfaceMilwaukee, WI · May 5, 2010#9
Looks fantastic garm!
cali yarisThread starterCanoga Park, CA · May 5, 2010#10
the strut supports are the sexy part, gotta have 'em! 😁

They also allow tuning of the front angle of the splitter.
CtrlAltDefeatIndianapolis IN · May 5, 2010#11
very nice... Any plans to sell them? 😁
severous01SE Texas · May 5, 2010#12
push pins hold the bumper on, the headlights in, the wheel wells in place...door panels...have you tried taking off the door panels? it's a pain.

any way, i'm talkin the ones with the button in the middle that forces the tips apart, it'd hold.

any way, looks good. i'm thinkin i may do somethin like that now. specially seein how cheap it actually is.
cali yarisThread starterCanoga Park, CA · May 5, 2010#13
I gotcha. "push pins" also hold paper to a bulletin board, I was a little confused there.

Those would work, I think; they're nice and flat, too.
bzinn 1University Place,WA · May 5, 2010#14
Beautiful splitter Garm.......makes me want to make one next year when the lip kit goes on.
yarrrnew mexico · May 5, 2010#15
Originally Posted by cali yaris ↑
"push pins" also hold paper to a bulletin board
hahaha, that's what I thought he meant too, and then when he said tape I had this picture of someone using tacks and scotch tape to do body work on their car...

splitter looks nice btw..
kacWest/Central Illinois · May 5, 2010#16
looks great.
CosmonautSanentoneyow, Tecksis · May 6, 2010#17
That is SWEET!

How much of a difference does is make for handling?
i know the general idea of it but in regards to your driving experience.
cali yarisThread starterCanoga Park, CA · May 6, 2010#18
not much effect under 100 mph, that's my thinking.
TRDMartyCorona CA · May 6, 2010#19
Originally Posted by cali yaris ↑
not much effect under 100 mph, that's my thinking.
AHH, but there is an affect of the visual kind cause who will be keeping up with you @ 100 mph to see it??

Way cool Garm 😎

Marty
kngrsllSpartanburg, SC · May 10, 2010#20
there is a formula that helps estimate the amount of downforce created. i think you just need surface area and speed to estimate.

the only problem is that is only really helpful if you know what the numbers are to begin with. i doubt there is alot of aero info on the yaris :)

If you look at designs similiar to ours, the faster you go, the greater the LIFT generated. This lift is usually higher in the front and lower in the rear. Just as example: At 100 mph, the front end is seeing 50 lbs of lift while the rear is seeing 25 lbs of lift.

Make sense? so a splitter that neutralizes that extra lift at speed would be pretty helpful for front to rear balance. Really helpful if you are doing track days and putting triple digit speeds down.

A car like ours will never really make alot in the way of downforce, the goal is more like reducing lift. Another example, the GTR has pretty good aero treatment, the result? A reduction in lift! It is almost a zero lift vehicle, pretty tough for a road car to accomplish.