Yarisworld Archive

FS: Push to Start Trim Piece

37 posts · 20,330 views

CTScottOriginal postUSA, CT · Apr 30, 2010#1
I bought a batch of these "Push To Start" trim pieces from Europe. These are used on European Liftbacks, which have the Push To Start feature. They fit perfectly with the JDM Vitz, Camry, Avalon, or Lexus PTS switch.

I bought enough to get a reasonable discount, so these are $30 shipped.

Here are some pictures of the piece and of one in my 09 Liftback with a JDM Vitz PTS switch installed.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

3 attachments not included in this copy

Replies 36

AothachosLong Island, NY · Apr 30, 2010#2
wont fit a sedan huh?
schleppyBoston, MA · Apr 30, 2010#3
How hard is it to wire up the actual button?
CTScottThread starterUSA, CT · Apr 30, 2010#4
Originally Posted by Aothachos ↑
wont fit a sedan huh?
No. I believe that the only sedans that have Push Button Start are right hand drive.
CTScottThread starterUSA, CT · Apr 30, 2010#5
Originally Posted by schleppy ↑
How hard is it to wire up the actual button?
I created a module that works with the OEM Engine Start/Stop Switch, and lets the switch start and stop the engine (and it drives the LEDs on the OEM switch).

There are 5 wires that connect between the switch and the module, 3 wires that connect to the ignition switch and one wire that gets tied to chassis ground.

Picture not included in this copy

Here's a video of the switch in action, which also explains the installation:

http://www.youtube.com/watch?v=v6zinlD58Eg

1 attachment not included in this copy

custom LftbackHouston, TX · Apr 30, 2010#6
So how much would it be for the whole set up? (trim piece, push to start button, and the module)
CTScottThread starterUSA, CT · Apr 30, 2010#7
Originally Posted by custom Lftback ↑
So how much would it be for the whole set up? (trim piece, push to start button, and the module)
Trim: $30 shipped
Module: $55 shipped
Switch: $35+ on eBay or ~$70 from your local dealer

The switch connector and pins are expensive from the dealer and hard to find from junkyards, so it is most cost effective to solder to the pins. If you purchase a switch and ship it to me I will do the soldering to the module wires (with an inline connector to make installing it easier) for no extra charge.

The picture above of the module and switch is an example of a direct wired switch - That one is alainmikli's TRD PTS switch, which I assembled for him last weekend.
TEHxFALLEN V1.2Calabasas, CA · Apr 30, 2010#8
Great Scott!! This is a great deal for an OEM trim piece with shipping!!

If I had the extra funds laying around, I'd definitely do this!!

Bump!!
TKOPhoenix · May 3, 2010#9
Would you happen to know if your start button would work in a 06 Scion xA?
CTScottThread starterUSA, CT · May 3, 2010#10
Originally Posted by TKO ↑
Would you happen to know if your start button would work in a 06 Scion xA?
I am not sure if the switch would be the same for the xA, but my module should work the same on an xA.
MistryWhere Only Yaris' Can Go · May 8, 2010#11
Would your module work even if the yaris has a remote start installed?
CTScottThread starterUSA, CT · May 8, 2010#12
Originally Posted by Mistry ↑
Would your module work even if the yaris has a remote start installed?
Yes. I recently made some changes to how I determine that the car is started to allow it to work properly with remote start.
fnkngrvIn The Hotbox · May 8, 2010#13
Just as a heads up when you pull the right hand trim piece off from the center console there is a round hole which looks to be that size to accommodate the push to start mechanism. I was going to use that hole for another project however this has my mind moving in a different direction. All one with a sedan would have to do is punch out the correct size hole and then would be able to mount the PTS I would wager.


Any insight or ideas on this CTScott?
CTScottThread starterUSA, CT · May 8, 2010#14
Originally Posted by fnkngrv ↑
Just as a heads up when you pull the right hand trim piece off from the center console there is a round hole which looks to be that size to accommodate the push to start mechanism. I was going to use that hole for another project however this has my mind moving in a different direction. All one with a sedan would have to do is punch out the correct size hole and then would be able to mount the PTS I would wager.


Any insight or ideas on this CTScott?
I just ran into this picture of Cyberfrogg's. This hole to the left of the radio is the PTS switch mounting hole:

Picture not included in this copy
yarisugiハワイ · May 8, 2010#15
Can't view the video! Damn Rick Astley keeps showing up on youtube! Firefox glitch?
Looks nice. Wish I could see the video for it.
fnkngrvIn The Hotbox · May 9, 2010#16
Originally Posted by CTScott ↑
I just ran into this picture of Cyberfrogg's. This hole to the left of the radio is the PTS switch mounting hole:

Picture not included in this copy

Yup...that is it which means that if the part number could be found then there must be a replacement panel for the sedan overseas that already has the hole as a factory spec...I was going to use it to run my USB for my HU through, but might need to 86 that idea and find a new spot as I kind of like the idea of the PTS...
FSANENY · May 22, 2010#17
mine is a full panel

is there a trim piece that I can use?

Picture not included in this copy
kazama82Malaysia · May 23, 2010#18
Originally Posted by CTScott ↑
I created a module that works with the OEM Engine Start/Stop Switch, and lets the switch start and stop the engine (and it drives the LEDs on the OEM switch).

There are 5 wires that connect between the switch and the module, 3 wires that connect to the ignition switch and one wire that gets tied to chassis ground.

Attachment 33598

Here's a video of the switch in action, which also explains the installation:

http://www.youtube.com/watch?v=v6zinlD58Eg

hi scott, will this module work with yaris sedan?..how much to shipped to Malaysia?
mick.wheelzBrisbane, Australia · May 23, 2010#19
wonder if i can get a RHD version of this from somewhere...
CTScottThread starterUSA, CT · May 24, 2010#20
Originally Posted by mick.wheelz ↑
wonder if i can get a RHD version of this from somewhere...
No need - If you have a liftback, then your dash already has the hole to the right of the steering wheel with a plug in it. You just pop the plug and shove the switch in.
FSANENY · May 24, 2010#21
Originally Posted by CTScott ↑
No need - If you have a liftback, then your dash already has the hole to the right of the steering wheel with a plug in it. You just pop the plug and shove the switch in.
if its a RHD, wouldn't the hole be on the left of the steering wheel?
CTScottThread starterUSA, CT · May 24, 2010#22
Originally Posted by FSANE ↑
if its a RHD, wouldn't the hole be on the left of the steering wheel?
Picture not included in this copy
FSANENY · May 24, 2010#23
Originally Posted by CTScott ↑
Picture not included in this copy
oh ok. thanks for the clear up.
kazama82Malaysia · May 24, 2010#24
Originally Posted by kazama82 ↑
hi scott, will this module work with yaris sedan?..how much to shipped to Malaysia?
🙁
CTScottThread starterUSA, CT · May 24, 2010#25
Originally Posted by kazama82 ↑
🙁
It definitely would work with a Malaysian Yaris. Shipping would be $10 to Malaysia.
mick.wheelzBrisbane, Australia · May 24, 2010#26
ah yes, i noticed that panel on mine, was not sure if the PTS button went there.
PhillyGgeorgia · May 25, 2010#27
oh man.. now you are making me want to do THIS mod to my LB.... im still waiting on the parts for the cruise control! that project is this weekend tho.. so if i get the trim and module from you all i would need is to get the switch?
PhillyGgeorgia · May 26, 2010#28
hey ctscott? how do i go about getting the trim piece and module from you?
PhillyGgeorgia · May 26, 2010#29
Originally Posted by CTScott ↑
Trim: $30 shipped
Module: $55 shipped
Switch: $35+ on eBay or ~$70 from your local dealer

The switch connector and pins are expensive from the dealer and hard to find from junkyards, so it is most cost effective to solder to the pins. If you purchase a switch and ship it to me I will do the soldering to the module wires (with an inline connector to make installing it easier) for no extra charge.
you still willing to do the connections if i can find a switch ans ship it to you? got a part number for the switch?
CTScottThread starterUSA, CT · May 26, 2010#30
Originally Posted by PhillyG ↑
you still willing to do the connections if i can find a switch ans ship it to you? got a part number for the switch?
Yes.

Vitz Japan/Corolla Japan/Rav4 Japan: 89611-52020
Vitz Japan/Corolla Japan/Rav4 Japan: 89611-52021

Yaris Europe: 89611-0D010

Camry/Highlander/Land Cruiser Japan: 89611-52011

Camry/Avalon USA: 89611-07010
PhillyGgeorgia · May 26, 2010#31
thanks! imma start looking and get one.. then ship it to you with a check? money order? hrmm?
PhillyGgeorgia · May 26, 2010#32
ouch.. id like to know where you found it for 35-70 bucks... the parts supply places online are charging 170
PhillyGgeorgia · May 26, 2010#36
allrighty then.. found the ones on trd sparks actually i saw it for 52 but have to wait anyways for two weeks.. Fiance says i cant spend any more money till then.. :-( will order it in two weeks and then pm you when it arrives about what to do. she loves the cruise control though so she aint saying no...... just wait for two weeks
PhillyGgeorgia · May 28, 2010#37
ok .. had a talk with the fiance.. she says go with foglights first.. so i guess i have to push the push to start button to the back burner... thanks anyways!