colinr5779Original postScotland/Glasgow · Apr 23, 2010#1ive ripped my original spoiler off (yaris sr 1.8) and im left with several holes.. none of which line up with the holes drilled on my spoiler !! anyone on here had to drill holes to get an aftermarket spoiler on?
advice/tips would be helpful cheers !
Replies 12
BilliamUSA · Apr 23, 2010#2I've installed both factory and aftermarket spoilers on several cars. The key is to take your time and make sure you have the templates lined up perfectly. Then use a center puch to mark the locations of the holes to be drilled. Start small (the smallest bit you can use) and step your way up until you reached the desired size. I then like to de-bur the holes and apply several coats of touch-up paint to the insides of the holes. I also like to put a little silicone sealant in the holes right before I install the spoiler.
One other tip I would give, is to mask off the back of the car, including taping up seams and such. That way you don't get metal filings everywhere.
BTW, I just did an OEM spoiler install on my Yaris. Went very smoothly...no issues.
ozmddDFW, TX · Apr 23, 2010#3The aftermarket RS-style spoiler I installed did not line-up with the oem locations I've seen on other cars. Mine came w/o a spoiler, so I had no pre-drilled holes, but I had to do some searching to figure out the best way to drill and use the hole locations on the new spoiler. If you don't want to drill into the inner wall of the liftgate, you can use an expanding "bolt" that anchors itself, kinda like a sheetrock anchor. If not, you'll have to drill through 2 layers of metal and anchor on a very angled piece of metal on the inside of the liftgate, near the hinges.
BilliamUSA · Apr 23, 2010#4 Originally Posted by
ozmdd ↑ ...you can use an expanding "bolt" that anchors itself...
If you're going to go this route...you're best bet is to use well-nuts. They will expand as the bolt is tightened without doing damage to the sheet metal around it.
colinr5779Thread starterScotland/Glasgow · Apr 24, 2010#5BilliamUSA · Apr 24, 2010#6 Originally Posted by
colinr5779 ↑ Cheers for the info ! i really didnt want to go drilling holes.. but it looks as if im going to have to :| wish is luck haha..
Once you get pass the shock of drilling into the car...you'll be fine. Oh, and good luck. 👍
cali yarisCanoga Park, CA · Apr 24, 2010#7 Once you get pass the shock of drilling into the car...you'll be fine.
yeah, and then it becomes addictive.
colinr5779Thread starterScotland/Glasgow · Apr 24, 2010#8Its on !!!! al post pics 2moro!!
nick.dollimountHalifax, NS Canada · Apr 24, 2010#9 Originally Posted by
cali yaris ↑ yeah, and then it becomes addictive.
Holy crap, you're right! 🤤
1NZYaris1New Zealand · Apr 25, 2010#10 Originally Posted by
nick.dollimount ↑ Holy crap, you're right! 🤤
😆 some one needs rehab , can i suggest you visit the Micro Image rehab centre , oh and please bring a valid credit card or cash 😁
marlondogLost Angeles · Apr 25, 2010#11I would just use double-sided tape. I recently bought the RBK spoiler and the instructions tell you to drill from the inside of the hatch into the spoiler. It was a pita to drill, and it seemed the drill bit did not want to go through. I just used the tape, and that bad boy isn't going anywhere(yet).
colinr5779Thread starterScotland/Glasgow · Apr 25, 2010#12BilliamUSA · Apr 25, 2010#13I dig it. 👍