VangOriginal postCA · Apr 9, 2010#1Ok, I just got my new Konig feathers and was installing them on my car using the OEM jack, and while doing the last tire, front driver side, the jack slid off and my car was resting on the brake rotors.. i paniced but with some quick thinking i safely got it back up with some help and placed the wheel on. looks like the rotor shield is bent up, but i bent it back in place. took it out for a test drive and seems like nothing is wrong with it, but im gonna take it to the dealer for inspection just in case.
im guessing the jack slid off because i was being an idiot and only chocked the rear wheels and not the front as well + was in the dirt.. the jack was stuck under the car and i had to lift it up to get it lol.. hard lesson learned but im still worried.
cliffs -
changing on new tires
car fell off jack and rested on rotors + jack
Replies 12
same thing happened to me when i tried to change a flat. promptly called the roommate to bring the 2-ton hydraulic floor jack. spare changed in 2 minutes. factory scissor jack is useless. if they only designed the spare well off-center then there would be room for a floor jack
Betriventedmonton · Apr 9, 2010#3My stock jack is bent sideways ish. Might've been from previous owners. It doesn't LOOK bent when it's completely retracted, but it can't lift the car worth crap. if I ever go on an extended road trip, I'm taking a hydraulic with me
SilverBackEl Monte, Ca · Apr 9, 2010#4Almost had this happen to me once while changing a flat. The OEM scissor jack moved while lifting and twisted slightly (like it was gonna buckle and give-out). Lucky for me I got the job done without anything bad happening. Since then I keep a small floor-jack in the car.
Also ditched the crappy OEM lugwrench for an old-school 4-way for better leverage.
MadMaxSan Antonio, Texas! · Apr 9, 2010#5I dropped my Jeep on one of the brake rotors when installing a lift kit, didn't phase it a bit...
VangThread starterCA · Apr 9, 2010#6 Originally Posted by
SilverBack ↑ Almost had this happen to me once while changing a flat. The OEM scissor jack moved while lifting and twisted slightly (like it was gonna buckle and give-out). Lucky for me I got the job done without anything bad happening. Since then I keep a small floor-jack in the car.
Also ditched the crappy OEM lugwrench for an old-school 4-way for better leverage.
yes this is what im doing from now on.. the oem supplied ones suck, but problem is now the better jack and lugwrench i have rattles in the trunk
KimmyCorpus Christi, TX · Apr 9, 2010#7ouch sorry to hear that! hope everything goes ok
VangThread starterCA · Apr 9, 2010#8just got back from and everything checked out alright, just the rotor shield bent and beat up but no safety issues. thanks.
thebarberGrand Rapids, MI · Apr 9, 2010#9time for a real jack and stands...
ddongbaphay · Apr 9, 2010#10SHould be ok right? I mean, that brake rotor is supposed to take tons of heat, so it must be built. Right?
VangThread starterCA · Apr 9, 2010#11 Originally Posted by
ddongbap ↑ SHould be ok right? I mean, that brake rotor is supposed to take tons of heat, so it must be built. Right?
yeah its alright but the whole car was resting on it lol
SilverBackEl Monte, Ca · Apr 9, 2010#12 Originally Posted by
Vang ↑ yes this is what im doing from now on.. the oem supplied ones suck, but problem is now the better jack and lugwrench i have rattles in the trunk
Mine does too, but the constant rattling is nothing compared to smashing a rotor against the asphalt at the worse possible time.
CosmonautSanentoneyow, Tecksis · Apr 13, 2010#13What ive seen the WRC guys do if they need to change a tire is put the spare under the frame while changing the tire.... i think they do it for safety reasons but it works the same. Ive been doing it like that since ive seen them do it.