1.5Original postTampa · Mar 16, 2010#1So I know this is a much debated topic and I have searched and Ive seen people running some low offset on their yarii, ive also seen a lot of people flame it. I am trying to get on more of an agreement. Im trying to pick up a set of xxr 002 wheels in 15x8 +0. I want to know will they fit. Some say there will be rubbing issues and others say its fine. Im fine with a tiny bit of rubbing at full turn because I rarely do that on the street and I plan on setting my camber to negative once I finish my suspension. Im going to be putting tein s-techs on with tokico blues so the drop will be around 2 in.
Im going for the flush look and I just want to know is 15x8 +0 doable or will it not fit?
Replies 117
coffiendOmaha, NE · Mar 16, 2010#2I'm on 15x7 xxr 513 : tein s tech : 185 55 15 tires and the rubbing wasn't as bad as I thought it was going to be. I imagine that when I get Canbered there will be no rubbing.
If I had to guess, I'd say you could pull it off with some camber and rolled fenders still with SOME rubbing.
Might be annoying, but it sure would look pretty.
1.5Thread starterTampa · Mar 16, 2010#3im so tempted to experiment anyways lol.
Mister ZRancho Cucamonga, CA · Mar 16, 2010#4I think it would also depend on the tire size you run.
1.5Thread starterTampa · Mar 16, 2010#5im gonna run something thin and really skinny for a stretched look.
coffiendOmaha, NE · Mar 17, 2010#6If you have the $$$ and time to expirement go for it man! It would look really nice.
The one thing that I want to point out is that even though you have the s techs, a really short sidewall on 15s might leave you with a not-so-hot wheel gap. I have a little more space than I would like ideally on mine bit can't afford coilover so I'm just going to have to suck it up till I can afford some.... Just a little food for thought ;)
anyways, I'm excited to see whatever you end up doing.
AdeJong 03LA, CA · Mar 17, 2010#7no matter how perfect your offset is, you will not sit flush on stechs purely because they dont go low enough
i just installed a set on my sedan hoping to cut my wheel gap to nothing but i still have a little over a one finger gap. flush is pretty much no wheel gap so im prob gonna end up switching out my suspension again to coilovers to go lower.
the stechs are way lower than the trds i just had but still not low enough for my taste
yarisugiハワイ · Mar 17, 2010#8You will sit flush, but rubbing will be inevitable if you want the flush look.
As for tires - if you run 195/45/15 which is the lowest profile you can get, it will poke a little.
You can stretch 175/50/15 or 165/50/15, but I wouldn't recommend 165, since its width is less than stock.
1.5Thread starterTampa · Mar 17, 2010#9I feel like the s-techs would be perfect cuz it will look almost flush but I wont be too low to worry about hard rubbing.
yarisugiハワイ · Mar 17, 2010#10a wheel with 15x8 +0 offset will poke in the front, poke in the back.
If you look at BrazdonW's car, he has 15x7 +15 and his wheels are pretty flush to the fenders. His pics are in this
link So if you go 15x8 +0, it will sit outside the fenders.
1.5Thread starterTampa · Mar 17, 2010#11^^^ perfect thats exactly what I want.
AdeJong 03LA, CA · Mar 17, 2010#12im running a 16x7 +38 front and +28 rear (because of pg 10mm spacers)
these pics are with stechs- the wheel gap is actually more noticeable in person.
Picture not included in this copy
Picture not included in this copy
if you run coilovers you can sit more flush and just increase spring rate- your suspension will travel less and chance of rubbing will be lower (due to stiffer suspension)
TamagoOff Grid · Mar 17, 2010#1315X8 +20 with a 225 50 15 barely fits inside the front fender.
15X8 +7 in rear pokes a LOT, with 225 50 15.
coffiendOmaha, NE · Mar 17, 2010#14If I'm not mistaken, brazdon is on stock rubber, meaning 185/60/15 and s techs.
The taller tire is why his wheel gap is minimal.
coffiendOmaha, NE · Mar 17, 2010#1515x7 +15 185/55/15 on S. Tech
Picture not included in this copy
Picture not included in this copy
yarisugiハワイ · Mar 17, 2010#16^ another fine example right there. :)
coffiendOmaha, NE · Mar 17, 2010#17thought maybe this one could help too.
again, S techs and 185/55/15
sorry for the dirty car.
Picture not included in this copy
1.5Thread starterTampa · Mar 17, 2010#18I want there to be a tiny bit of space I feel like that would alleviate most of the rubbing I would get during street driving. and Im not planning on going with a 225 tire im gonna stretch on something thinner and I am gonna put something low profile so that should also help. I think between the skinny/thin tires and the small gap left with the s-techs I should eliminate almost any rubbing.
marlondogLost Angeles · Mar 17, 2010#19Stay close to stock height(185/60,195/55,205/55) as possible. When you have short tires, you end up having a big gap. If you want to drop your car more to fill in the gaps, you will rub and scrape everywhere. Besides, the Yaris has a high roof and doesn't look too good with little tiny wheels and tires. Too low is good for show, but it's wack if you ain't driving on smooth roads or the track!(Jessie Jackson speaking about lowered cars)
As far as wheels, you shouldn't go wider than 7''(15x7,16x7,17x7) with a 38 offset(38-45). You will still need to add adjustable camber bolts to the front to tuck them in and to keep from busting up your fenders(anything from 38-41 will need camber). If you have spacers in the rear, I suggest you add the washers to get negative camber, or just take them off.
Stick to what works. That way, you don't have to keep changing things out and wasting time and money. You wanted a second opinion, and you got one. Good luck!
TamagoOff Grid · Mar 17, 2010#20 Originally Posted by
marlondog ↑
As far as wheels, you shouldn't go wider than 7''(15x7,16x7,17x7) with a 38 offset(38-45). You will still need to add adjustable camber bolts to the front to tuck them in and to keep from busting up your fenders(anything from 38-41 will need camber). !
there are dozens of members here running +30mm offsets here, with no fender problems. don't regurgitate internet knowledge..
AdeJong 03LA, CA · Mar 17, 2010#21i just mentioned im running a +28 rear
the difference is i just shaved my rear fender- but now because of that i think i am actually capable of running a 22-25 on a 7 inch wide wheel with the appropriate sized tire. I am trying at the moment to work out a deal for some work emotions so if I do I am going to ask my tire guy to let me try on different tires and use spacers to see how aggressive i can afford to sit.
I want my tires to be flush but stretched tires arent my thing so im hoping I can run a 205/45 or 215/45 on these new 17x7s and have perfect fitment
coffiendOmaha, NE · Mar 17, 2010#22"Stick to what works. That way, you don't have to keep changing things out and wasting time and money. You wanted a second opinion, and you got one. Good luck!"
OP already stated that he WANTED to expirement.
That's half the fun, right? Making something work that is out of the ordinary. I know oi would want to settle on something that I didn't really like because it was the easy way out....
marlondogLost Angeles · Mar 17, 2010#23Like that guy with the blue Yaris with the Racing Dynamics and the 13mm hub spacers? He nearly took off his front fender doing autocross. I think he was running 30 offset wheels.
As far as what I know, it's based on "experimenting" and not having a good time fixing it(i.e tires,wheels,camber). Been there,done that!
Alot of people will disregard what someone says, because they don't want to hear no. I don't know which other way to say it.
If you want to spend time and money changing out tires and wheels,adjusting camber,changing out shocks and springs, pulling and rolling fenders,stretching out tires to fit on wheels they're not designed for, then go for it!
No one is trying to rain on anyone's parade. If people are so sure about it, then they shouldn't ask questions. If you get told it's a pita, believe it.If they say it's easy, don't believe it.
Originally Posted by
Tamago ↑
there are dozens of members here running +30mm offsets here, with no fender problems. don't regurgitate internet knowledge..
AdeJong 03LA, CA · Mar 17, 2010#24its not that hard to experiment
you just need a combination of spacers, a tire guy who will let you test fit some tires, and a jack and jackstand
this is how the hellaflush guys do it all the time. if you want to see how a wheel will fit your car then just jack the wheel into the fender and see what the tire hits
judging by how my wheels are fitting currently, it looks like you can make the wheel perfectly flush with the body on with a x7 +35 in the front and +25 in the rear (im talking about adding 10mm spacers without camber shims). tire rub is a different story. im just talking about proper wheel fitment. if you want to poke/ stretch- please do experiment and post results.
- and dont quote me on this. im still experimenting as well
the emotions i am trying to get are +42 but i am going to attempt a 10mm spacer in the front and 18-20mm in the rear. ill post results once i get there but i do plan to completely shave the excess metal off my fenders
i am also going to do the rear suspension mod to reduce my toe angle around the same time. this is all dependent on whether or not i get the wheels obviously but we shall see. i may just attempt to run an extra 5mm spacer on the team dynamics i have currently to see what kind of fitment i could achieve with a +33 front and +23 rear
aeipee13los angeles · Mar 17, 2010#25Anyways, I'm running +37 up front with +24 in the rear (PG 13mm spacers), 15x7 with 195/55/15 tires on DF springs. It rubs occasionally in the rear when loaded down and I hit a bump too fast. Aside from that everything is good.
I'll try to get photos but i don't really care enough to take the time to do it.
AdeJong 03LA, CA · Mar 17, 2010#26 Originally Posted by
aeipee13 ↑
Anyways, I'm running +37 up front with +24 in the rear (PG 13mm spacers), 15x7 with 195/55/15 tires on DF springs. It rubs occasionally in the rear when loaded down and I hit a bump too fast. Aside from that everything is good.
I'll try to get photos but i don't really care enough to take the time to do it.
rolled or cut fenders?
aeipee13los angeles · Mar 17, 2010#27nope. It's almost perfect, the rear fender barely hits the side wall of the tire. I'm running Dunlop Direzza Z1 star spec. If i had better than the crap DF spring rate i'd probably be fine as is. I could take a bat to the fender or just let nature take it's course and let the tire do the job.
I think your "experimental" fitment would be the perfect fit.
1.5Thread starterTampa · Mar 17, 2010#28thanks guys for your input and Im not trying to blow money but I believe where there's a will there's a way lol. I wana poke out and I want a deep wheel thats why Im looking at +offset and 8in wheels. I want to experiment and I want to be different.
kngrsllSpartanburg, SC · Mar 17, 2010#2915x7 +25 and i never rub.
1.5Thread starterTampa · Mar 17, 2010#30i like to hear things like that ^^ lol
1.5Thread starterTampa · Mar 17, 2010#31would 15x8 with a +15 offset make any difference in rubbing issues?
aeipee13los angeles · Mar 18, 2010#32 Originally Posted by
1.5 ↑ would 15x8 with a +15 offset make any difference in rubbing issues?
yeah. i think that's just over the "limit" of what a stock wheel well can handle.
AdeJong 03LA, CA · Mar 18, 2010#33 Originally Posted by
aeipee13 ↑ yeah. i think that's just over the "limit" of what a stock wheel well can handle.
depends on the tire, suspension and what you do the the fenders
if you think about it, a x8 +15 is the equivalent of a x7 +2 or +3
you will most certainly poke the wheels out though if thats what youre looking for
nerd_vitZSan Diego · Mar 18, 2010#34once i get my car back to the states (in about a month or two) im going to be test fitting some 15x8 +6 offsets in the front. also im going to be trying to fit 15x10 +0 offsets in the rear. i highly doubt the rears will fit, but im going for the aggressive stance so we'll see. heres pics of the car theyre coming off of and the exact wheels they are. im also getting tein coilovers and possibly camber to make it all fit. i'll definitely post pics and info when we work on it.
http://www.stanceworks.com/canibeat/?p=8039 Shoutout to SDSF and Supastar!
1.5Thread starterTampa · Mar 18, 2010#35well if 15x8 +0 is absolutely going to be a problem which seems to be the consensus then I guess ill be going with 15x8 +15 and ill still get to poke which is what im going after.
TamagoOff Grid · Mar 18, 2010#36 Originally Posted by
1.5 ↑ well if 15x8 +0 is absolutely going to be a problem which seems to be the consensus then I guess ill be going with 15x8 +15 and ill still get to poke which is what im going after.
how about 15X9 +36?
http://www.tirerack.com/wheels/Wheel...All&sort=Brand Picture not included in this copy SplitEdmonton · Mar 18, 2010#37you guys are crazy.. you want to be running the HIGHEST offset possible because that's what this car is set-up for. If you're doing a 15x8, you'll want at least a +40 offset. if you run a high enough offset, you might even be able to get away with running a 225 width tire.. like a 225/45R15. Or if you want that stretched look you can run a 215/50R15. <- that's about as far as you can safely stretch onto a 15x8.
aeipee13los angeles · Mar 18, 2010#38Really Split?
coffiendOmaha, NE · Mar 18, 2010#39^ haha. simple, yet effective.
TamagoOff Grid · Mar 18, 2010#40 Originally Posted by
Split ↑ you guys are crazy.. you want to be running the HIGHEST offset possible because that's what this car is set-up for. If you're doing a 15x8, you'll want at least a +40 offset. if you run a high enough offset, you might even be able to get away with running a 225 width tire.. like a 225/45R15. Or if you want that stretched look you can run a 215/50R15. <- that's about as far as you can safely stretch onto a 15x8.
you're wrong actually..
and i hate stretch.
AdeJong 03LA, CA · Mar 18, 2010#41 Originally Posted by
Split ↑ you guys are crazy.. you want to be running the HIGHEST offset possible because that's what this car is set-up for. If you're doing a 15x8, you'll want at least a +40 offset. if you run a high enough offset, you might even be able to get away with running a 225 width tire.. like a 225/45R15. Or if you want that stretched look you can run a 215/50R15. <- that's about as far as you can safely stretch onto a 15x8.
incredible amount of misinformation
also, the op isnt actually asking for what the widest he can run is, he wants to know how aggressively he can make his wheels fit.
1.5Thread starterTampa · Mar 18, 2010#42thank you guys and im starting to second guess the 15x8+0 rims cuz I dont want to have to blow money to pull and roll fenders and shit or have to have too much negative camber and have to replace tires once a year so i think ill be going with the 15x8+15 as it sounds like that wheel wont cause as many problems. and Im not going high offset or wide tires.
TamagoOff Grid · Mar 18, 2010#43 Originally Posted by
1.5 ↑ thank you guys and im starting to second guess the 15x8+0 rims cuz I dont want to have to blow money to pull and roll fenders and shit or have to have too much negative camber and have to replace tires once a year so i think ill be going with the 15x8+15 as it sounds like that wheel wont cause as many problems. and Im not going high offset or wide tires.
15X8 + 20 is cheap.. and no herpeMAX XXR wheels.
Picture not included in this copy Picture not included in this copy aeipee13los angeles · Mar 18, 2010#44 Originally Posted by
1.5 ↑ thank you guys and im starting to second guess the 15x8+0 rims cuz I dont want to have to blow money to pull and roll fenders and shit or have to have too much negative camber and have to replace tires once a year so i think ill be going with the 15x8+15 as it sounds like that wheel wont cause as many problems. and Im not going high offset or wide tires.
Adejong's "fitment" of 15X7 +35 front and +25 rear is perfect if you don't want to roll fenders. I run 15X7 +37 front, +24 rear without rolled fenders. If the my fronts were +35 it would be better looking. If the rear were +25 i don't think i would rub when i hit bumps.
I originally got deleted for calling out Split and his misinformation; i had to "simplify" my response. I guess admin actually read the post and are letting the people handle it now.
GideonSunnyvale, CA · Mar 18, 2010#45 Originally Posted by
Tamago ↑ 15X8 + 20 is cheap.. and no herpeMAX XXR wheels.
As claimed ealier in the thread:
Originally Posted by
marlondog ↑ Like that guy with the blue Yaris with the Racing Dynamics and the 13mm hub spacers? He nearly took off his front fender doing autocross. I think he was running 30 offset wheels.
I don't want to seem as if I'm fueling the flame here, but if we're going to nip misinformation in the butt, I figured I'd point this out. Obviously Tamago since you've seen Enth's car run, you can chime in as to whether or not there's any issues with his fitment and auto-x runs?
TamagoOff Grid · Mar 18, 2010#46 Originally Posted by
aeipee13 ↑ Adejong's "fitment" of 15X7 +35 front and +25 rear is perfect if you don't want to roll fenders. I run 15X7 +37 front, +24 rear without rolled fenders. If the my fronts were +35 it would be better looking. If the rear were +25 i don't think i would rub when i hit bumps.
I originally got deleted for calling out Split and his misinformation; i had to "simplify" my response. I guess admin actually read the post and are letting the people handle it now.
it's kimona, who likes to keep us in the dark about what kimona considers "cookie cutter" fitment.
apparently it's a sore spot..
1.5Thread starterTampa · Mar 18, 2010#47i have no idea what you guys are even talking about right now lol
marlondogLost Angeles · Mar 18, 2010#48Here's what I'm talking about. The front wheels have a +30 offset and the rears +17.
1 attachment not included in this copy
TamagoOff Grid · Mar 18, 2010#49 Originally Posted by
1.5 ↑ i have no idea what you guys are even talking about right now lol
bottom line...
do what you have to do. 0 offset on an 8" wheel is gonna poke.
20 offset with 8" is gonna poke with a "proper" sized tire.
you're out to build a showqueen with stretched tires. why are you even on yarisworld asking questions? go to herra-frush dot cawm. stretch it, poke it, make it look stupiid, rub, ruin tires, all in the name of being herrafrush. .. . .
if you're sensible though, stick to 7" wide wheels and nothing lower than a 20 offset out back and 30 offset up front. enjoy being able to turn your car without destroying your fenders.
yarisugiハワイ · Mar 18, 2010#50I built a show queen. =P
For reference: -REAR- 15x8.5" +13 offset = 1.75" poke out of stock fender (no pull or roll)
Picture not included in this copy