Yarisworld Archive

Has any1 got a 1zz tb that sucessfully works

14 posts · 4,164 views

Toy YarisOriginal postMelbourne , Australia · Feb 19, 2010#1
Hi guys,
I've ordered a 1zz tb now i'm wondering if i should cancel it as most of the posts here a negative about the 1zz tb. I want to know if any one has done this successfully and does it actually make a difference? if so can you please explain the process that needs to be done please.
thanks😕

Replies 13

Maitre_Te_TeQuébec · Feb 19, 2010#2
I have one 1zz TB and it work great when engine hot. No CEL, just fine with a litlel bug at 3000 if I release de gaz, it maintain, but for me, this is not a big probleme. I will do a chip swap with 2 Spare TB (1zz and 1nz)
cali yarisCanoga Park, CA · Feb 19, 2010#3
1. Take a stock 1NZ throttle body, and drill out the rivets that hold the plastic controller to the body. Do the same thing with your 1ZZ throttle body.

2. Chip away the protective sealant on the 1ZZ's adjustment screw.

3. Use small bolts/nuts to install the 1NZ "chip" (black plastic end) onto the 1ZZ throttle body.

4. adjust the screw as needed. The screw determines how open the plate is at idle. If you're revving too high at idle you'll have to back this off by adjusting the screw.

Disconnect the battery for a while to force your motor to go into relearn mode (I can't remember how long).

Does that help?
kngrsllSpartanburg, SC · Feb 19, 2010#4
Originally Posted by cali yaris ↑
1. Take a stock 1NZ throttle body, and drill out the rivets that hold the plastic controller to the body. Do the same thing with your 1ZZ throttle body.

2. Chip away the protective sealant on the 1ZZ's adjustment screw.

3. Use small bolts/nuts to install the 1NZ "chip" (black plastic end) onto the 1ZZ throttle body.

4. adjust the screw as needed. The screw determines how open the plate is at idle. If you're revving too high at idle you'll have to back this off by adjusting the screw.

Disconnect the battery for a while to force your motor to go into relearn mode (I can't remember how long).

Does that help?
did know you could do that?? cool...
YodaFL · Feb 19, 2010#5
I didnt need to adjust anything. Just a chip swap was fine the ecu can adjust the idle by itself.
Toy YarisThread starterMelbourne , Australia · Feb 19, 2010#6
Originally Posted by cali yaris ↑
1. Take a stock 1NZ throttle body, and drill out the rivets that hold the plastic controller to the body. Do the same thing with your 1ZZ throttle body.

2. Chip away the protective sealant on the 1ZZ's adjustment screw.

3. Use small bolts/nuts to install the 1NZ "chip" (black plastic end) onto the 1ZZ throttle body.

4. adjust the screw as needed. The screw determines how open the plate is at idle. If you're revving too high at idle you'll have to back this off by adjusting the screw.

Disconnect the battery for a while to force your motor to go into relearn mode (I can't remember how long).

Does that help?
Thanks yes it does help, but do i swap the electronics or the whole black plastic thing?
Thanks again
tk-421Dagobah · Feb 19, 2010#7
Yeah just replace the black plastic base and it'll work. 👍
PHXDEMONPhoenix, AZ · Feb 19, 2010#8
good luck.
Toy YarisThread starterMelbourne , Australia · Feb 20, 2010#9
I guess i will give it a go will be getting it in a few weeks as a mate owes me money . now coolant lines connect or bypass??
and the tb gasket do you use the old 1 or just use sealastic, i was thinking of using the old gasket and toyota black sealastic ??
eiiLong Beach, CA · Feb 20, 2010#10
undefined
tk-421Dagobah · Feb 20, 2010#11
Originally Posted by Toy Yaris ↑
I guess i will give it a go will be getting it in a few weeks as a mate owes me money . now coolant lines connect or bypass??
bypass
xxae07xxhouston · Feb 20, 2010#12
i dont understand why ive never had problems with my tb...i never swapped chips or any of that stuff. revs oscillated for about 10 after the swap and that was it. no cel or nething and that was a good yr and a half ago...
cali yarisCanoga Park, CA · Feb 20, 2010#13
do i swap the electronics or the whole black plastic thing?
That is where the electronics are. 🙂

Most trouble occurs because of sealing/gasket problems. Make sure to use the rubber O-ring. You'll notice it has one spot that leads to the outside of the TB. So, if you don't use that gasket (or seal it properly with other material), you will have a leak.
Toy YarisThread starterMelbourne , Australia · Feb 23, 2010#14
Cool thanks guys will give it a go, will let you know how it goes..