Yarisworld Archive

Question regarding replacing studs...

21 posts · 8,391 views

DerFlosserOriginal postUSA · Feb 1, 2010#1
I am considering using a spacer in the rear and while searching, I was not able to come across an answer to my question. Is replacing the studs as easy as driving them out after taking off the face of the drum? OR...does one have to remove the pads, springs, pins etc....as well as the rear plate to drive out the studs and insert the new ones? I can't get my car on the lift as my other car is currently in the garage so...any insight would help. 👍

Replies 20

kngrsllSpartanburg, SC · Feb 1, 2010#4
yah, just knock them out with a hammer, get an open ended nut, and tighten them back in!
YAR1SRaleigh, NC · Feb 1, 2010#5
Originally Posted by DerFlosser ↑
I am considering using a spacer in the rear and while searching, I was not able to come across an answer to my question. Is replacing the studs as easy as driving them out after taking off the face of the drum? OR...does one have to remove the pads, springs, pins etc....as well as the rear plate to drive out the studs and insert the new ones? I can't get my car on the lift as my other car is currently in the garage so...any insight would help. 👍
its pretty easy once you get the drum face off.
and you can even use some m8(i think) bolts to get the drum off without tapping it with a hammer.... worked very well with mine. 👍
DerFlosserThread starterUSA · Feb 1, 2010#6
I just looked at some pictures and it doesn't look like there is enough room to get the old studs out nevermind get the new ones in. Can somebody who has actually done this let me know if it's possible by only removing the drum face? Thanks again!
ozmddDFW, TX · Feb 1, 2010#7
Never mind... thinking of hub bolts.
DerFlosserThread starterUSA · Feb 2, 2010#8
OK....so in the 07' Repair Manual it seems to state pictorally that you can indeed knock them out after simply removing the drum face. For those that went with the 10mm spacers....how much longer is the stud? Is it a full 10mm or is it more like 5mm? I am assuming that the lenght is negligible upon installation of the new studs. I really would love to confirm this. Thanks!
cali yarisCanoga Park, CA · Feb 2, 2010#9
H&R studs are longer by exactly the width of the spacer. I can't answer for other brands.
DerFlosserThread starterUSA · Feb 2, 2010#10
Originally Posted by cali yaris ↑
H&R studs are longer by exactly the width of the spacer. I can't answer for other brands.
Thanks for that bit of input. I am also curious as to how those who have done this keep the hub from turning when pulling the new studs through(that is aside from the screwdriver trick in the repair manual). 👍
WeeYariGeorgetown, Ontario, Canada · Feb 2, 2010#11
I pulled mine through with an electric impact wrench. Worked beautifully without spinning the hub.
DerFlosserThread starterUSA · Feb 2, 2010#12
Originally Posted by WeeYari ↑
I pulled mine through with an electric impact wrench. Worked beautifully without spinning the hub.
Great. Thanks! Did you upgrade to longer studs?
WeeYariGeorgetown, Ontario, Canada · Feb 2, 2010#13
Had to. Stock studs with a 10mm spacer only left me with approx 3 or 4 exposed threads for the wheel lugs to grip. Also explains why I responded about using an impact wrench to pull them through ;)
DerFlosserThread starterUSA · Feb 2, 2010#14
Originally Posted by WeeYari ↑
Had to. Stock studs with a 10mm spacer only left me with approx 3 or 4 exposed threads for the wheel lugs to grip. Also explains why I used an impact wrench to pull them through ;)
OK....was this on the front or rear? The reason I ask is because I am trying to find out if I am on the right track here. 🙂 If it was the rear, can you install these by simply removing the drum face and hammering out the old studs while simply installing the new ones through the back of the hub face (using said washer, lugnut and impact)? I am trying to prepare myself for a simple 30 minute to 1 hour job as opposed to thinking it's super simple and spending 6 hours on it and being frustrated as all hell. 👍 Your input if greatly valued! 🍻
WeeYariGeorgetown, Ontario, Canada · Feb 2, 2010#15
Question first. Are you installing hub spacers or wheel spacers?
DerFlosserThread starterUSA · Feb 2, 2010#16
Originally Posted by WeeYari ↑
Question first. Are you installing hub spacers or wheel spacers?

wheel spacers. I already have hub spacers. Hub spacers don't affect stud length as you know. 👍
WeeYariGeorgetown, Ontario, Canada · Feb 2, 2010#17
Thought so, just wanted to be sure. Post#3 confused me a bit.

So yes, it is as simple as all that.

- pull of drum
- start a lug nut onto the stud to protect threads and tap out with a hammer
- insert new longer strud through back of mounting plate. There are only a couple of spots within the drum where there will be enough room to slid the new studs in.
- slid on washer and nut, and tighten down

Done.
DerFlosserThread starterUSA · Feb 2, 2010#18
Originally Posted by WeeYari ↑
Thought so, just wanted to be sure. Post#3 confused me a bit.

So yes, it is as simple as all that.

- pull of drum
- start a lug nut onto the stud to protect threads and tap out with a hammer
- insert new longer strud through back of mounting plate. There are only a couple of spots within the drum where there will be enough room to slid the new studs in.
- slid on washer and nut, and tighten down

Done.
Awesomeness. Thank you very much for confirming this!👍
WeeYariGeorgetown, Ontario, Canada · Feb 2, 2010#19
np
YarisSedanCalifornia - Bay Area · Feb 2, 2010#20
Just a tip put the lugnut on backwards when you are pulling out the new stud and make sure its 100 percent centered till the tapered part is flush against the back of the hub. You might have a use a washer between the lugnut depending on the threads. Also put a dab of antisieze on the tread when pulling it flush. And be careful when removing the lugnut off to put the wheel back on after you pulled the new studs in place they will be extremly burning hot to the touch.
DerFlosserThread starterUSA · Feb 2, 2010#21
Originally Posted by YarisSedan ↑
Just a tip put the lugnut on backwards when you are pulling out the new stud and make sure its 100 percent centered till the tapered part is flush against the back of the hub. You might have a use a washer between the lugnut depending on the threads. Also put a dab of antisieze on the tread when pulling it flush. And be careful when removing the lugnut off to put the wheel back on after you pulled the new studs in place they will be extremly burning hot to the touch.
Gotcha...knew most of that for the most part but does it take that much effort to pull them through that the nut/wahers/stud get that hot? Interesting. Thanks!🍻