hyprmilerOriginal postWisconsin · Dec 21, 2009#1I'll have my scangage in tomorrow. =) Free overnight shipping is amazing. =)
I can't wait to see what kind of numbers I'll be pulling.
Replies 26
cali yarisCanoga Park, CA · Dec 21, 2009#2Aww, didn't support a supporting vendor? 😢
you'll like the Scangauge, it's easy to read and very useful.
hyprmilerThread starterWisconsin · Dec 21, 2009#3Sorry didn't go with the local vendor this time. 🤷
Next time though.
hyprmilerThread starterWisconsin · Dec 21, 2009#4Do you guys sell any of the quick drain oil plugs? Or are those gimmicky?
127.0.0.1NE · Dec 21, 2009#5 Originally Posted by
hyprmiler ↑ Do you guys sell any of the quick drain oil plugs? Or are those gimmicky?
they may be gimmicky. regular plug cannot fail, those might and sometimes do. is engine damage worth the time saved ?
yaris-meAnaheim, CA · Dec 22, 2009#6Fumoto FTW.👍
jambo101Montreal Canada · Dec 22, 2009#7After you get used to the gauge a bit you might want to set the X gauge to show average mpg as the real time mpg reading is all over the place..
X gauges are a bit of a cluster f--- to set up but the average mpg setup goes like this=
From the home screen ( button with red around it ), hit more>more>more>xgauge
Now you can select the memory slot. If its already on 0 and this is the first xgauge you are creating, go ahead and hit the edit button.
You should now be at the TXD screen
Use the + and - buttons on the left side so that the first number is 0 Then use the arrow button on the right side to move over one space Now it depends on what trip function you want to use..
use the + or - again to adjust
0 - for current trip which resets every time you start the vehicle
1 - for today trip which resets after 10 hours of ignition off time
2- for previous day
4- for tank trip
on mine I have 01 for average fuel economy today
next hit the OK button
You should now be at the RXF screen
use the + or - buttons until the first digit is 8.
Then push OK button 3 times until you get to the name screen
Here you can pick any three letters to name your gauge.
I used AFT for average fuel today
Then hit save
Now you can go back to the home screen and hit gauge. Select which of the four spot you want the gauge to appear and hit the button until see the three letters that you just used to name your gauge.
hyprmilerThread starterWisconsin · Dec 22, 2009#8mind if I ask where ya'll mounted yours?
cali yarisCanoga Park, CA · Dec 22, 2009#9when i had one, i put it right in front of me on the steering column.
hyprmilerThread starterWisconsin · Dec 22, 2009#10So I got it in the mail today, and so far I love it.
Still need to mess around with it and get it fully programmed. I think I'm going to zip tie / mount it to my GPS unit.
So far it seems to be fairly accurate when it comes to usage, I just need to get it calibrated and fully set before I trust it any further (not to mention do some math to make sure it's not sweet talking me).
127.0.0.1NE · Dec 23, 2009#11 Originally Posted by
hyprmiler ↑ So I got it in the mail today, and so far I love it.
Still need to mess around with it and get it fully programmed. I think I'm going to zip tie / mount it to my GPS unit.
So far it seems to be fairly accurate when it comes to usage, I just need to get it calibrated and fully set before I trust it any further (not to mention do some math to make sure it's not sweet talking me).
if you fill up using the exact same gas pump, parked the exact same way, and stop at the first
click every time, it cannot do anything but calibrate itself correctly over 2 or 3 tanks. this may vary.
preprogram it for a 2.9 offset and it'll be really close to perfect
(given you do the initial setup properly)
hyprmilerThread starterWisconsin · Dec 23, 2009#12out of curiosity... why 2.9 offset?
127.0.0.1NE · Dec 23, 2009#13 Originally Posted by
hyprmiler ↑ out of curiosity... why 2.9 offset?
because that is what my offset ended up to be and
2.9 will probably get you accurate mileage from the first tank
you can choose not to set it, and it'll take 3 or 4 tanks to
be sure the offset is accurate. 'cuz your first two tanks will be
off, and leave you wondering. you'll prob end up at 2.9 or 3.2
anyhow if you have a 1.5 liter yaris
hyprmilerThread starterWisconsin · Dec 23, 2009#14I just can't find a good place to mount this damn thing....
I think I'm going to try and fasten it to the bottom of my GPS mount. That's tomorrow's task.
Doc ZaiusOttawa, ON, Canada · Dec 24, 2009#15I popped off my A-pillar trim and ran it up there, under the headliner, and mounted it on top of the rear-view mirror. Not a bad spot for it... although a bit hard to read when it's bright out due to contrast.
127.0.0.1NE · Dec 24, 2009#16put mine right on the steering wheel hump in front of the storage bin
shoe-goo and velcro strip. cable up the back side. looks like it belongs there
hyprmilerThread starterWisconsin · Dec 25, 2009#17I don't trust this thing till it's calibrated... but I'm averaging 30-42mpg on the highway on trips.
I set the 11gallon tank
I set the 1.5 Liter engine
The only puzzling thing for me was when I did a full fillup it asked me to cycle though (very slowly I might add) how much I put in the car. I assume I don't touch that and leave it at zero? The quick reference guide wasn't very helpful or specific on that.
127.0.0.1NE · Dec 25, 2009#18you tell it how much gas you put in
if it's estimate is exact and shows what you put in, don't touch it
if it is off, adjust it by what you actually put in
then put in the cost
it is all in the user manual
hyprmilerThread starterWisconsin · Dec 25, 2009#19Yea I did that, just >_<
Merry Christmas btw.
Twistoffate0817Voorhees, NJ · Jan 29, 2010#20Is this or the eco meter better for instant MPG readings?
talnlnkySpokane, Wa · Jan 29, 2010#21 Originally Posted by
Twistoffate0817 ↑ Is this or the eco meter better for instant MPG readings?
i believe the ecometer refreshes twice per second, and the SGII you can set to refresh once every two seconds, once a second, or twice a second.
Kongo-OttoGermany · Jan 30, 2010#22I received my Scangauge II yesterday. Does anybody know if the Horsepower XGauge is supposed to work on the Yaris? I know it cant be very accurate but i just want to know this.
Hard_YarisEdmonton Alberta · Jan 30, 2010#23I got my Horsepower working on the Scangauge II... not sure its accurate reading 11hp some of the time...
then 0hp while in gear and not pressing on the gas. Very Cool for Gas Savings. Take advantage of DFCO (Deceleration Fuel Cutoff).
Master ShakeVA · Feb 1, 2010#24I have a scangauge and love it.
Kongo-OttoGermany · Feb 3, 2010#25 Originally Posted by
Hard_Yaris ↑ I got my Horsepower working on the Scangauge II... not sure its accurate reading 11hp some of the time...
then 0hp while in gear and not pressing on the gas. Very Cool for Gas Savings. Take advantage of DFCO (Deceleration Fuel Cutoff).
I gave it a try and its working now. I dont know how exact the calculation is but it is a funny gadget for sure. 🙂
talnlnkySpokane, Wa · Feb 4, 2010#26 Originally Posted by
Kongo-Otto ↑ I gave it a try and its working now. I dont know how exact the calculation is but it is a funny gadget for sure. 🙂
yeah... i programmed the HP function in last fall.... fun toy for about 15 minutes. I don';t think i've ever seen it go over 80. most of the time it doesn't go above 40. When I idle its in the single digits (2-5hp).
The most helpful guages i've found so far are MPG/MPH/TPS/FWT/RPM.... sometimes i'll look at voltage, air intake, or LOD.
Kongo-OttoGermany · Feb 5, 2010#27I found out that my Scangauge shows me a zero under full throttle. Looks like it thinks the fuel cut is working. Any solution to this? The TPS value is default = 24.