Yarisworld Archive

Lowest offset

17 posts · 5,039 views

Mister ZOriginal postRancho Cucamonga, CA · Dec 6, 2009#1
Whats the lowest offset and widest wheel run on a yaris?

Replies 16

yarisugiハワイ · Dec 6, 2009#2
You can run whatever you like. Depends on how you want your car to look and/or perform.
You have to be more specific on what kind of look you want.
There is a sticky thread on wheels in this section (above).
by the way... welcome to YW.
SilverBackEl Monte, Ca · Dec 6, 2009#3
Welcome to YW!

You also have to ask yourself if you plan on suspension mods too. If so which method: lowering springs, struts, or coilovers? Certain ride heights and spring rates can cause rubbing at certain offsets and rim + tire sizes. It just depends on what you're willing to deal with while driving...
Mister ZThread starterRancho Cucamonga, CA · Dec 6, 2009#4
I'm looking at wheels that are 16x8 +0 offset all around. As far as suspension goes, I was either going with coilovers or the Tein s-techs as this springs give the lowest drop from all the available springs.
supmetSouthern California · Dec 6, 2009#5
There are pics of 15x8 with 20 offset in this thread. Not sure if it helps.. I'd talk to tamago about it, and he could tell you if its doable and/or if you need hub spacers or anything.

NOOB HERE need wheel help

Also, I think DF210s are lower than tein s.techs
Mister ZThread starterRancho Cucamonga, CA · Dec 6, 2009#6
From what I have read is that the s-techs drop the car 1.9 inches all around. The DF210s drop 1.8 in the front and 1.6 in the rear. Unless i am mistaken?
toadbowser's castle · Dec 6, 2009#7
Originally Posted by Mister Z ↑
From what I have read is that the s-techs drop the car 1.9 inches all around. The DF210s drop 1.8 in the front and 1.6 in the rear. Unless i am mistaken?
actually, it's 1.6 front and 1.8 rear👍 however, many people say the dfs sag a little so maybe the difference is minimal🤷
TheRealEnthMiami, FL · Dec 11, 2009#8
if you get coilovers, you'll be fine with that setup
BrentoriusMelbourne, FL · Dec 11, 2009#9
Originally Posted by TheRealEnth ↑
if you get coilovers, you'll be fine with that setup
As long as the ride height is stock!

An 16x8" wheel with 0 offset assuming 205/40 tires will stick out 55mm or 2.2" more than stock steelies/rubber.

Plus the speedometer will read 5.5% faster.

Definitely a no-go with the S-techs!
Black YarisToledo, OH · Dec 11, 2009#10
to tuck a 8 inch wide +0 offset you will have to run a good amount of negative camber and or stretch your tires, or just get a wide body kit..... either way it is just ugly and pointless
coffiendOmaha, NE · Dec 11, 2009#11
^ opinion. Some people like stretch + camber.

Guilty as charged.
MateoNear St.Louis · Dec 12, 2009#12
^ I agree man... maybe I spent to much time on vwvortex when I had my jetta. 🤤
TamagoOff Grid · Dec 12, 2009#13
good luck making it fit.

i'm guessing you're looking at XXR wheels. shame
07blackvitzIrvine Ca · Dec 12, 2009#14
I have 15x8 XXR 501 wheels on my car i tested 0-offset XXR 513 but they poke way to much you gonna have to add lots of camber and have your fenders rolled and pumped to run 0's with +15s im running 3.5 negative camber front and rear with a stretch tire lowered on Tein coilovers and rolled the fender.
yarisugiハワイ · Dec 13, 2009#15
How the heck do you get -3.5 camber in the fronts?
Black YarisToledo, OH · Dec 13, 2009#16
Originally Posted by yarisugi ↑
How the heck do you get -3.5 camber in the fronts?
strut modification
07blackvitzIrvine Ca · Dec 13, 2009#17
What i did was get the SPC camber bolt for the top bolt and ran a Toyota camber bolt for the bottom i forgot what the part number is for the thinnest one is but thats how i got 3.5 negative camber for the from and for the rear i made my own shims similar to what Penguin was selling just a thicker washer.