PETERPOOPOriginal postOahu · Nov 11, 2009#1Well I went to the dyno today. The last time I went to the dyno, I managed to get 133whp. However, that was on my first and only pull. The reason I only did one pull was because I was running too lean to continue with anymore pulls. After that I got 1zz injectors, and my lean problem is non existent. I only now finally made it to the dyno again, and got to do three pulls.
This is my "before" dyno. The reason I say that is, because I had NST make me a custom overdrive crank pulley, with a smaller water pump pulley. This will hopefully give me a couple more lbs of boost. I will be going to the dyno again this Saturday to get my "after" dyno results done. For now, here are my results from today...
Mods: blitz s/c, aFe intake, Megan Header, 2.25" headerback exhaust, 1zz injectors.
Probably could make a few more whp if I had the 1zz throttle body and water/meth injection. However, I don't have plans on using those two. Just the overdrive crank pulley which will be installed and dyno'd this saturday, and then eventually tune everything up with the greddy emanage ultimate.
1st pull in 3rd gear: 136 whp 135tq
2nd pull in 4th gear: 135whp 133tq
3rd pull in 3rd gear:
140whp 135tq
I am positive about the whp numbers, just can't quite remember the torque numbers. I know they only varied from 133-135whp.
I don't have the dyno sheet. The printer was out of ink, and I will get it on Saturday when I dyno with the new pulleys.
Here are the pulleys that I will be installing for the dyno on Saturday.
Originally Posted by NonStopTuning ↑
The first ever CUSTOM NST Overdrive Crank Kit for the Blitz SC Toyota Yaris
Picture not included in this copy
👍👍
Replies 28
cali yarisCanoga Park, CA · Nov 11, 2009#2that just plain ROCKS. very nice. 👏
how much boost did you see at peak?
what was the A/F at peak?
can't wait for Saturday... 😲
H3LlIoNMidatlantic · Nov 11, 2009#3 Originally Posted by
PETERPOOP ↑ Mods: aFe intake, Megan Header, 2.25" headerback exhaust, 1zz injectors.
I can just see somebody rolling in here and being like "Holy sh%t, you picked up 33hp with intake and exhaust!!! 🙄
What did the pulleys cost? One thing too I never knew, is the stock rating of 106 at the wheels or crank? I'm assuming your 140 is to the wheels...
MorganPCB, FL · Nov 11, 2009#4wait.... when did nst make an overdrive pulley?
yarisugiハワイ · Nov 11, 2009#5I think PETERPOOP forgot to add one more important mod to that list. :)
PETERPOOPThread starterOahu · Nov 11, 2009#6woops. blitz s/c ;)
h3lion: I wrote "whp." So yah, to the wheels. Stock is about 85 whp. Toyota advertises 106 to the crank.
Morgan: I've been in talks with them for months about it. ;)
Garm: My AFR on the dynojet was 12-12.5 I believe. However my wideband reads 10.5. They were saying it must be the hi flow cat that is making it read higher ( since they read the AFR from the exhaust tip ). My max boost was 8 lbs of boost.
yaris-meAnaheim, CA · Nov 11, 2009#7All that power and no where to go. 🙂 What's happening with Barbers Point? 🤷
1NZYaris1New Zealand · Nov 11, 2009#8nicely done peter 🙇 🙇.
i will be waiting and watching like everyone else .
All the best for Saturday , you might just make it to half of Garms 310. sorry just stirring 😆
🙌
ozmddDFW, TX · Nov 11, 2009#9Wow! That's a mighty-fine set of pulleys. Glad to see someone really doing things "right", and using a quality-first approach. I think you've got a damn solid setup there. I'm excited to see the updated dyno. BTW - what brand of dyno?
yarisugiハワイ · Nov 12, 2009#10PETERPOOPThread starterOahu · Nov 12, 2009#11wrong. dynojet @ radmotorsports. ;)
H3LlIoNMidatlantic · Nov 12, 2009#12 Originally Posted by
H3LlIoN ↑ What did the pulley cost?
?
PETERPOOPThread starterOahu · Nov 12, 2009#13Since the pulleys are not on the market yet, I don't think I should say. Not sure what NST will be trying to sell them for, if successful.
thebarberGrand Rapids, MI · Nov 12, 2009#14hard to say what they'll charge...
cali yarisCanoga Park, CA · Nov 12, 2009#15ok, let's clear up a couple of things, besides huge PROPS and CONGRATS to peterpoop!
140 whp @ 8 psi is really good for that little blower.
@ thebarber: The overdrive pulleys are for a very small limited market, so they will be a short run and I will bet a paycheck (what's that?) at least a little more expensive.
If NST makes a run, I'll be selling them AND pre-packaged with supercharger kits.
Stock is about 85 whp.
<-- I think 90-95 is what has been reported most frequently.
thebarberGrand Rapids, MI · Nov 12, 2009#16was just throwing out an idea....perhaps i shouldnt have...
yarisugiハワイ · Nov 12, 2009#17You went to RAD - I see.
They better have ink for the printer by Sat.
PETERPOOPThread starterOahu · Nov 12, 2009#18was it 95whp garm? Yah, i don't think I've ever seen a stock dyno.
anonymous userwindward oahu · Nov 13, 2009#19There's stock dyno graphs around here somewhere. The owner of a shop had a yaris dynoed on oahu. It prolly got lost in that stupid hack last year, or earlier this year.
LtNoogieWest Hills, CA · Nov 15, 2009#20Good going, Peter. You could probably get one or two hp more with the old muffler but people on Maui would complain about how loud it is.😆
PETERPOOPThread starterOahu · Nov 15, 2009#21true that! it was a true straight flow design. hey noogie, did you ever install the AEM meth kit yet? I thought you bought it....
chongopantsHouston · Nov 15, 2009#22140whp is awesome, I wish I could get there soon :(
LtNoogieWest Hills, CA · Nov 15, 2009#23 Originally Posted by
PETERPOOP ↑ true that! it was a true straight flow design. hey noogie, did you ever install the AEM meth kit yet? I thought you bought it....
It's still sitting in the garage. One day.
Have you looked at your spark plugs lately?
PETERPOOPThread starterOahu · Nov 15, 2009#24yah i have, they looked ok. however, i don't have my compressor on at all really.
<<<<<<sits and waits.....
PETERPOOPThread starterOahu · Nov 17, 2009#26kngrsllSpartanburg, SC · Dec 8, 2009#27i dyno'd 86 stock...
anonymous userwindward oahu · Dec 9, 2009#28 Originally Posted by
kngrsll ↑ i dyno'd 86 stock...
Woohooo!!
People don't believe me when I say 108 to the crank.
Now i can say 86BHP, and whip all the cars at auto-x (that is until i fix my real auto-x car).
cali yarisCanoga Park, CA · Dec 9, 2009#29^ if it was on a dyno, that's probably 86 whp, not bhp