Replies continued
RevssonSoutheast Wisconsin · Dec 19, 2011#51That ebay site says automatic transmission only, and Devilgirl has a MT.
In one of the posts on a prior page, it states a different part number for a MT kit.
If that is the correct parts number, I could ask my dealership if they have one in stock
or could get one. Can someone verify that part number for the MT?
bronsinnj · Dec 19, 2011#52 Originally Posted by
Revsson ↑ That ebay site says automatic transmission only, and Devilgirl has a MT.
In one of the posts on a prior page, it states a different part number for a MT kit.
If that is the correct parts number, I could ask my dealership if they have one in stock
or could get one. Can someone verify that part number for the MT?
As I understand it same part manual or auto.
The part goes in the engine block what could be different AT to MT?
RevssonSoutheast Wisconsin · Dec 20, 2011#53 Originally Posted by
bronsin ↑ As I understand it same part manual or auto.
The part goes in the engine block what could be different AT to MT?
I was just going by this previous post in the thread:
Block heater I have thought about a block heater, but haven't had the need that I see.
The only time I would want one is at work, and outlets are hard to come by.
I have a garage here at my apartment, so the car is relatively warm and
I don't have to scrap the windows in the morning. Sometimes the outside
of the window will fog up on the way out. 😛
bronsinnj · Dec 20, 2011#54I am hoping the bh will improve mpgs since I only drive the car 6.7 miles to work. If it warmed up faster you would think mpgs would go up.
DevilGirlLehigh Valley, PA · Dec 20, 2011#55I'm just interested in not freezing when I leave for work at 4am. It gets mighty chilly at that hour!! 🙁👎
bronsinnj · Dec 20, 2011#56 Originally Posted by
DevilGirl ↑ I'm just interested in not freezing when I leave for work at 4am. It gets mighty chilly at that hour!! 🙁👎
My experience so far is it makes the cool engine light go out after half a mile instead of a mile plus. Note the coolant temp is only 140 degrees F when the light goes out. So you dont really have heat yet even with the light out.
I wonder if people who have the bh can say if it hellps get heat to the interior noticeably sooner?
swedeON CAN · Dec 24, 2011#57 Originally Posted by
Kluak ↑
anybody purchase this one on ebay and install it? Want to know its good before I buy
BuildCodeNorthern Illinois · Dec 24, 2011#58Either of those should be fine, they look similar. They fit the auto easier than the manual, as you will see from my pics in this thread. I bought mine from a dealer in MN (I think??) that gets them from Canada, they aren't very common in the US. I believe the recommendation is in this thread as well.
And as far as interior heat goes, my ScanGauge reads water temps of a little over 100 deg F after using the block heater overnight, which as mentioned doesn't translate to much heat, since the cold LED stays on till 130 deg F. It does help for getting non-freezing air onto the windshield for faster defrosting. I am currently experimenting to see the shortest amount of time I need the block heater on to get to the max temperature.
BuildCodeNorthern Illinois · Dec 24, 2011#59I still had my PM from user R2D2 who helped me pick my block heater out, PU140-00900 is for the auto, so that will fit. C0140-00900 is for the manual, but you can make the auto version fit manual just fine as I did. And the dealer is Burnsville Toyota of MN.
swedeON CAN · Dec 25, 2011#60Great! Just bought it!
BuildCodeNorthern Illinois · Dec 26, 2011#61 Originally Posted by
swede ↑ Great! Just bought it!
Cool let us know how it goes!
naossoanMB, Canada · Sep 29, 2012#62I'm having a really hard time actually finding the damn hole for the block heater. I saw some pictures where the one for the automatic trans goes, but I have a manual transmission.
Is it in the exact same spot? I jacked the car up as I had better mobility to feel around from the underside of the car, but I could still not feel the hole to insert the heater plug into.
Where exactly is it?
Like....I took the battery out, then just to the left (when standing facing the car) and down of the battery is (I believe) the shifter cables/linkages. Just to the right of that is some kind of....I dunno it's kind of a clunky thing and I can move it with my hand. Seems to have something to do with shifting too. Is it just to the left, and down a smidge from that thing?
I guess it's kind of hard to explain without a picture.
Here are some pictures I manged to take by getting my hand up inside with my camera on my phone. Does it plug in where this little plastic thing is? Or...where is it around here?! This is the shifter cable plate thingy is the darker coloured metal.
EDIT::: Here is a link to an imgur album with some of the pictures.
http://imgur.com/a/7fjcc#0 Where in relation to where these pictures are taken is the plug hole?
BuildCodeNorthern Illinois · Sep 29, 2012#63I don't think you'd have an easy time at all getting to it from the bottom of the vehicle.
Yes it is in the same location for manual trans, just a little more blocked by the linkages which is sounds like you found (move them and have someone watch the gear shifter and you'll know!)
It certainly sounds like you're close to finding it. The inside is very smooth and machined feeling. I don't think words will help as much as the pictures on here.
naossoanMB, Canada · Sep 29, 2012#64WOW was that a pain in the ass AND THEN SOME.
For anyone with a Manual transmission, and I believe this has been said before:
You MUST unbolt the shifting cable mounting bracket thingy. I even had to undo where they connect to the shifting things with the little clips.
You MUST remove a 10mm screw for a wire which is right there.
You MUST remove the small mount in which that wire was screwed into.
The instructions for the block heater make it appear that it slides in from the BACK (back as in the the part of the engine furthest away from the front bumper). THIS IS NOT THE CASE! It slides in FROM THE SIDE! From Right -> Left if facing the engine compartment from the front of the car.
If you don't remove all those parts then the plug cannot slide in straight and it will get STUCK. This happened to me, as I didn't think I needed to remove the small mount for the wiring harness, but once I removed it it slid in easy-peasy.
The other thing is that once you install it, things are extremely tight in there. I was able to re-attach the small mount for the cable, but I was not able to re-attach the cable to that mount, the rubber part of the block heater plug was in the way of this. I even made sure that the plug was pushed in all the way, which is was.
While re-mounting the shifting cable bracket thing it seemed like it just BARELY fit back on. It was right up against the side of the block heater threading (which is useless anyway not sure why it's there).
I double checked to make sure I had the right block heater plug, and it says for the 1NZ-FE engine 1.5L so it had to be the right one, but my god was it tight.
The actual location of the plug is directly beside where the shifting cables bracket thing and the small mounting bracket for that cable is. The actual hole is invisible from the front/side of the engine because there are too many other hoses and stuff in the way, you have to feel for it which is also very awkward and hand-cramping.
Careful when you undo the bolts for the shifting cable bracket, I smashed my hand really hard against the heat shield by the exhaust manifold when the bolt gave, so wear some gloves.
There weren't many good pictures of this location/installation so I took some:
Picture lost · imgur.com

bronsinnj · Sep 29, 2012#65I did mine on my auto trans. There no brackets to remove or anything. But finding the hole and inserting the heater is more involved than it needs to be. All the pictures dont help an aweful lot.
Remove the battery definately.
If someone has an engine out of the car and can post a pic of the location that would help more than anything else.
AltitudeColorado · Sep 29, 2012#66RESIZE YOUR PICS PLEASE
Hard_YarisEdmonton Alberta · Oct 22, 2012#67Just replaced my blockheater a few days ago...
Was a lot to take apart to get at... it was a little tight and most of it happened by feel, took me about 1.5h from start to finish.
the one i pulled out had a ripped boot and was not connecting properly... i did find a folded up piece of cardboard under the plug of the block heater.... when i unfolded the cardboard it was a toyota parts chunk of cardboard... not sure if this is a Toyota Certified fix or not.
cosadoBoise, ID · Jan 16, 2014#68naossoan
Thank you for the pictures! They helped more than anything I've found so far
Amdkt7Nashville, TN · Nov 9, 2014#69Well, I spent a bunch of time trying to find the hole. I found one hole where I thought it should be, but it was not big enough for the heater that I got. Looking at the pictures again I think that was the wrong hole. It should be on the edge of the block, but I could not see anything or feel any holes in that area. Frustrated. I guess I'm going to take it to the dealer to let them install it.
Frank NecrosisYoungstown, Oh · Feb 16, 2017#70After several years of use, my block heater failed. The wires on the plug end became frayed and shorted out. I would prefer to replace the whole heater & cord assembly.
The challenge has been finding part number C0140-00900. My car has a manual trans. I would like to order the correct part this time instead of modifying a heater for an auto trans car.
Any idea where to get p/n C0140-00900 these days? My searches are not finding anything for sale.
Amdkt7Nashville, TN · Feb 17, 2017#71I may have that one Frank. I bought one and never installed it. I could not find a way to access the hole, and never took it anywhere to have it done. The one I bought was for a manual transmission. If you are interested send me a message. I will have to check the part number when I get home.
Amdkt7Nashville, TN · Feb 28, 2017#72I responded, though I don't see it in my private messages (sent). If you don't get my message (Frank N), then post here.
atomic_hojiKincardine, ON, Canada · Nov 12, 2017#73Since this thread is already resurrected, I thought I'd add to it.. 😁
I was looking for the Toyota OEM block heater, but read that Toyota Canada recently issued a recall for the factory unit due to manufacturing faults that could lead to a short circuit.
https://www.toyota.ca/toyota/en/abou...-block-heaters If you can't find the OEM model, the recall may have affected your region as well.
I found 2 options for aftermarket, cartridge style block heaters that are listed to fit our cars:
- Kat's Heaters, p/n: 11813
- Zerostart (Phillips-Temro), p/n: 3100129
When I went to the local Ideal Supply (NAPA in Canada) they said they don't carry the Kat's, that it's only in the U.S. stores. The Zerostart, made by Phillips-Temro, is the one stocked in the Canadian stores.
Installation follows the information given in this thread. There's also a good YouTube video install on a Tacoma and Corolla if you search.
Hope that helps someone stay warm this winter. 👍
-- Adam
David CMontreal · Nov 16, 2017#74I just installed mine on my '07 HB auto. The pictures Naossoan posted really helped. I simply fisted my right arm down there and moved stuff around till I felt a hole underneath the metal hose. Then the fight was to get the Phillips-Temro heater I bought off Amazon.ca (~$53 CAD) in just the right Tetris location so it could slide straight in without snag on the hose and cables. Had to push harder from different positions to get the heater clip to snap in, but all in all it took me about 15 minutes under light cold rain.
Then to run the cord to the front grill. Fugget about it. I park in my yard and when it snows the front grill is 6 feet under. Good luck rampaging the extension cord with the shovel at 4am in the morning. I bought the Noco GCP1 AC port and plan on installing it by the black plastic flashing near the passenger side view mirror if there's enough depth (need 1.5"). That would keep the cord in clear sight and out of the snow so I can easily operate.
David CMontreal · Nov 20, 2017#75IronYarisSaskatchewan · Oct 24, 2021#76 Originally Posted by Ukrainian ↑
What sort of lube was included?
Dielectric grease? Thermal paste?
IronYarisSaskatchewan · Oct 24, 2021#77How easy was it to put everything back?
ZippoYarisBC, Canada · Nov 20, 2022#78This is for a 2007 Yaris with auto trans?
It looks like the right one as for some reason 2007 has a 90 dergree plug end on the heater end, eh?!
I had an issue with my electrical plug in end and decided to just cut the old one off and solder a three prong plug I had from an old programable timer. It was a pain to add but I didn't feel like taking the whole cord out. If my fix last until Spring then I will get this new one.
Thanks for the post and I hope this thread is back to life now!! 👍
Originally Posted by Ukrainian ↑
ZippoYarisBC, Canada · Nov 24, 2022#79Just an update. I got the block heater this morning via Purolator!! The price total was $84. Heater $65, Shipping $15 & Taxes $4. I am pleased as this is a genuine Toyota replacement part unlike all those other heaters you see on Amazon and PartsAvatar, etc. With shipping it costs about the same anyway!
Toyota even revises these things! Mine is REV 03 date of 7/22 on it! Yay!

JakeVIIICanada · Apr 24, 2025#80Does anyone know of a block heater that would be compatible with a 2008 Toyota Vitz with a 2SZ-FE engine?