Yarisworld Archive

N/A setup

23 posts · 14,019 views

Maitre_Te_TeOriginal postQuébec · Oct 5, 2009#1
Il want to do this tread for compare all N/A setup.

My yaris setup:
1zz TB
1zz injector
Borla axel back ( TRD parts )
Home made 2.5 inchs cold air intake

I want to install a free flow catalitic convertor and a 2 inchs exhaust

16 inchs DAI light wight
Eiback coil spring
Trd rear sway bar

I need some idea for my project.

Tanks!

Replies 22

thebarberGrand Rapids, MI · Oct 5, 2009#2
2.5" intake is too big, won't work with the MAF

forget the axleback and get a custom-made exhaust from the resonator back. the cats and resonator are 2" thru and the exhaust shrinks to 1.75" after the resonator. i had mine replaced last week....its worth the effort. skip the high flow cat, not worth the time/effort.

get a dc header because all the other headers are junk

nst underdrive crank pulley and lightweight water pump and alternator

1zz throttle body is ok

1zz injectors not likely req'd for n/a setup

wait for cali_yaris's intake manifold

get lightweight 15" rims, skip the 16's
Maitre_Te_TeThread starterQuébec · Oct 5, 2009#3
Tanks, but for de 2.5 intake, I have buy a fiting for this. I ajust the diameter for the MAF!

http://www.sfxperformance.com/parts/SPT9405.htm

For the cat hi flow, this is because I got one at the past and it is in my room!

tanks for your help!
ruimondPerth, Australia · Oct 5, 2009#4
Originally Posted by thebarber ↑
forget the axleback and get a custom-made exhaust from the resonator back. the cats and resonator are 2" thru and the exhaust shrinks to 1.75" after the resonator. i had mine replaced last week....its worth the effort. skip the high flow cat, not worth the time/effort.
Haha i didn't realise the piping for the cat and resonator were 2" already. Only remembered the exhaust place saying that the piping that they cut off from mid to muffler was 1.75". Guess that's good that i got 2" piping down then.

Hehe learnt some new info.🙂
jounabayamon puerto rico · Oct 5, 2009#5
wat i did is from the maf to the throttel. is put 2 inch tube and from the maf to the fog light 3 inches is kind of wat the aem v2 intake does
posaunemeisterKansas City, MO · Oct 5, 2009#6
Originally Posted by thebarber ↑
the cats and resonator are 2" thru and the exhaust shrinks to 1.75" after the resonator.
About 3 or 4 weeks ago, I tried to do a DIY axleback and failed miserable, because I read many times on the forum that our stock axleback exhaust pipe diameter was 1.75", but it's actually smaller than that. I measured a 1 3/8" ID for the piping just before it enters the muffler. I have an '08 Yaris 'S', but It should not be different than any other Yaris hatchback.
Maitre_Te_TeThread starterQuébec · Oct 5, 2009#7
The 1nz-fe have a 11:1 compression ratio but the prius have a 13:1 compression ratio. What is the different? Piston or culass (head) ...

Because I think that for the N/A setup, if we boost the compression ratio, we can win 10 hp... maybe!?!?
blacksandiegovitzJust chillin' out brah ! · Oct 5, 2009#8
Originally Posted by thebarber ↑
2.5" intake is too big, won't work with the MAF

forget the axleback and get a custom-made exhaust from the resonator back. the cats and resonator are 2" thru and the exhaust shrinks to 1.75" after the resonator. i had mine replaced last week....its worth the effort. skip the high flow cat, not worth the time/effort.

get a dc header because all the other headers are junk

nst underdrive crank pulley and lightweight water pump and alternator

1zz throttle body is ok

1zz injectors not likely req'd for n/a setup

wait for cali_yaris's intake manifold

get lightweight 15" rims, skip the 16's
+2
t0m4sPanama · Oct 6, 2009#9
Originally Posted by thebarber ↑
2.5" intake is too big, won't work with the MAF

forget the axleback and get a custom-made exhaust from the resonator back. the cats and resonator are 2" thru and the exhaust shrinks to 1.75" after the resonator. i had mine replaced last week....its worth the effort. skip the high flow cat, not worth the time/effort.

get a dc header because all the other headers are junk

nst underdrive crank pulley and lightweight water pump and alternator

1zz throttle body is ok

1zz injectors not likely req'd for n/a setup

wait for cali_yaris's intake manifold

get lightweight 15" rims, skip the 16's
cali_yaris is doing an intake manifold???? 👍 where are the updates for this?
TamagoOff Grid · Oct 6, 2009#10
Originally Posted by Maitre_Te_Te ↑
The 1nz-fe have a 11:1 compression ratio but the prius have a 13:1 compression ratio. What is the different? Piston or culass (head) ...

Because I think that for the N/A setup, if we boost the compression ratio, we can win 10 hp... maybe!?!?
no...
crxgamesWalton, Kentucky · Oct 6, 2009#12
Originally Posted by Maitre_Te_Te ↑
The 1nz-fe have a 11:1 compression ratio but the prius have a 13:1 compression ratio. What is the different? Piston or culass (head) ...

Because I think that for the N/A setup, if we boost the compression ratio, we can win 10 hp... maybe!?!?
Prius has a 1nz-fxe which has a completely different style head for efficiency. Though, you are correct that it has a 13:1 compression ratio. The lower end is also suppose to be the same as the 1nz-fe. Your best bet would be to do a 1nz-fxe bottom end with an adapted 1nz-fe head. There is a thread with a lot of details on the possibilities of this somewhere on clubxb.com, though it has not been done yet.

I personally wanna see this done, I just don't have the money to do it right now since I'm building an S13.
TamagoOff Grid · Oct 6, 2009#13
Originally Posted by crxgames ↑
Prius has a 1nz-fxe which has a completely different style head for efficiency. Though, you are correct that it has a 13:1 compression ratio. The lower end is also suppose to be the same as the 1nz-fe. Your best bet would be to do a 1nz-fxe bottom end with an adapted 1nz-fe head. There is a thread with a lot of details on the possibilities of this somewhere on clubxb.com, though it has not been done yet.

I personally wanna see this done, I just don't have the money to do it right now since I'm building an S13.
no, the prius bottom end is nothing special.
lilredrocketDFW, Texas · Oct 6, 2009#14
Tamago didn't you look up the piston part number and they were different?
crxgamesWalton, Kentucky · Oct 6, 2009#15
Originally Posted by Tamago ↑
no, the prius bottom end is nothing special.
Very true. I just looked everything back up.

The extra compression appears to come from the different pistons, no? Someone on scionlife saw gains with 11:1 pistons and an emanage tune.
http://scionlife.com/forums/showthread.php?t=65124
Maitre_Te_TeThread starterQuébec · Oct 6, 2009#16
Ho yeah, I have read this. 13 WHP with prius piston and e-menage. I will look for this !!!!!
PHXDEMONPhoenix, AZ · Oct 6, 2009#17
Originally Posted by Tamago ↑
no...
Explain please. i was under the impression higher compresion = more air/fuel/HP 🤷
advocatelocation · Dec 6, 2009#18
Originally Posted by thebarber ↑
forget the axleback and get a custom-made exhaust from the resonator back. the cats and resonator are 2" thru and the exhaust shrinks to 1.75" after the resonator.
Barber what do you think about getting a custom exhaust done from the catback instead of the resonator back? Why did you recommend to the OP that he start after the resonator?

Is there any other exhaust piping that needs to be increased to 2" besides the resonator-to-muffler piping?

Also if you're running an axleback already would it be easy to go to a muffler shop and have them convert from an axleback to a catback?
thebarberGrand Rapids, MI · Dec 6, 2009#19
Originally Posted by advocate ↑
Barber what do you think about getting a custom exhaust done from the catback instead of the resonator back? Why did you recommend to the OP that he start after the resonator?

Is there any other exhaust piping that needs to be increased to 2" besides the resonator-to-muffler piping?

Also if you're running an axleback already would it be easy to go to a muffler shop and have them convert from an axleback to a catback?
the cat and resonator are right after one another....and it may have been lost in the hack, but when magnaflow was fitting their system to the yaris, they said the cat and res were both 2" thru...so no real need to remove the resonator unless you want a louder exhaust

i paid $200cash for my 2.25" crush-bent exhaust piece from the res to the axle section...

Picture not included in this copy

Picture not included in this copy
advocatelocation · Dec 6, 2009#20
Originally Posted by thebarber ↑
i paid $200cash for my 2.25" crush-bent exhaust piece from the res to the axle section...
Did you have them attach the custom pipe to an axleback you already had installed? Is that possible?

So the piping is the right size after the res but is there another piece that needs to be increased? Maybe the up pipe or the down pipe?
thebarberGrand Rapids, MI · Dec 6, 2009#21
i think its 2" from the header to the backside of the resonator....then it goes down to 1.75"

i had a megan axleback when i had the midpipe done, so ya, they built me a pipe with a new flange to attach to the axle back (any axleback)
advocatelocation · Dec 7, 2009#22
Awesome that's what I wanted to know. Thanks for the help.
sujonol78Indonesia · Dec 7, 2009#23
hi there. i came across this forum when i was browsing for some parts for my 1NZ-FE ( Toyota Vios ). Since we are using the same engine, i thought we could share some of our experiences.

My name is Sujono, M, 32 y/o from Jakarta, Indonesia.
here's what I do with my 1nz-fe:
JFC air filter
Intake induction system
TRD clutch and clutch cover
Apexi Neo
CamCon
Custom exhaust manifold ( straight type, about 3mm larger than the standard one, 4:1 )
Custom muffler

with the Apexi Neo and CamCon working together, I can easily control the AFR and the timing.

dyno test ( without camcon and custom exhaust manifold ): 173Nm ( 4500 RPM ) & 132BHP ( 6000 RPM ).

looking forward to have a good discussion on how to improve our 1nz-fe performance ;)

cheers