Yarisworld Archive

Blinding blue indicator light

68 posts · 16,842 views · page 1 of 2

birdmanOriginal postUSA · Sep 30, 2009#1
When driving the Yaris on dark nights the blue high beam indicator light is so bright that it becomes annoying. I thought I read some where that a resister can be added to reduce the intensity of the light. Has anyone had any success with a fix for this one?

Thanks, Birdman🆘

Replies 67

puetato89orlando · Sep 30, 2009#2
i always half-ass the high beams so it doesnt come on, pretty much inbetween hi and lo it shines more aswell
puetato89orlando · Sep 30, 2009#3
i know, but it blinds when it is really dark out and it gets destracting
puetato89orlando · Sep 30, 2009#4
lol, ok maybe not blinds but still annoying,
AstromanWenatchee, WA · Sep 30, 2009#5
I also find it VERY annoying. I'm about ready to put electrical tape over it 😆
puetato89orlando · Sep 30, 2009#6
or just do what i do😉
birdmanThread starterUSA · Sep 30, 2009#7
You're right,"blinding" is an exaggeration. When I do long late night commutes and my eyes are tiring the brightness of the blue light is annoying, For now I wad up a paper towel to cover it.
BluYrsTallinn, Estonia · Sep 30, 2009#8
Some well-placed scotch tape to diffuse the light a bit?
birdmanThread starterUSA · Sep 30, 2009#9
The tape is an option but I'm hoping for an electrical fix. Thanks for the idea.
MGarganoNJ · Sep 30, 2009#10
Upgrade your headlights to bi-xenon HIDs from Xenon-Vision. For some reason, the way the kits gets wired, it stops the hi-beam indicator from lighting up on the cluster even though the hi-beams work perfectly.
SilverBackEl Monte, Ca · Sep 30, 2009#11
Just don't drive with hi-beams on in the first place. If that little blue light annoys you, just imagine how the driver in front of you feels
TheRealEnthMiami, FL · Sep 30, 2009#12
If that little blue light annoys you, just imagine how the driver in front of you feels
LAWL, just get strong foglights
CTScottUSA, CT · Sep 30, 2009#13
In the picture below, you can see the BEAM LED (D559). You could change its current limit resistor (looks like R640 {which is currently a 202 ohm resistor}, following the trace) to a higher value. Or, a much easier approach is mechanically reduce its output. My standard method for toning down overly bright LEDs on things is to simply dab the LED's lens with a black Sharpie marker. You can also use a think piece of gray or semi opaque plastic.

Beam LED.jpg
scapeBeaufort, South Carolina · Sep 30, 2009#14
i really dislike blue LED indicator lights that show up on everything these days, it truly is annoying, and the blue itself is way too bright; as for the dashboard, i think it makes sense to have one as you don't want to be driving around with your brights on all night-- that's not fair to others, so you should be reminded that it is on; even if it's a tad annoying. so to sum up, I bring nothing productive to the OP, hah :D
you could always crack open the dash and just replace the LED, or add a piece of painters tape onto the front for long drives
marcustoronto, canada · Sep 30, 2009#15
Originally Posted by birdman ↑
When driving the Yaris on dark nights the blue high beam indicator light is so bright that it becomes annoying. I thought I read some where that a resister can be added to reduce the intensity of the light. Has anyone had any success with a fix for this one?

Thanks, Birdman🆘
get a black electric tape and tape over it you wont even notice the tape..
bronsinnj · Sep 30, 2009#16
Yeah if you can get at the circuit board masking the LED itself is the way to go.
supmetSouthern California · Sep 30, 2009#17
There have been studies that show blue light creates more eye strain than any other color, but as others have pointed out, its a function, not a side effect.
AstromanWenatchee, WA · Sep 30, 2009#18
My '71 ford had a red light for the high beam. Much nicer. 🙂
birdmanThread starterUSA · Sep 30, 2009#19
Thanks for all your insights. I seem to remember an article that placed the resister in the wiring coming off of the head light assemblies under the hood (bonnet). Not having to tear apart the dash would be a real plus. But if tearing the dash apart to do it is what I have to do then so be it. I'm after an inconspicuous fix.
CTScottUSA, CT · Sep 30, 2009#20
Originally Posted by birdman ↑
Thanks for all your insights. I seem to remember an article that placed the resister in the wiring coming off of the head light assemblies under the hood (bonnet). Not having to tear apart the dash would be a real plus. But if tearing the dash apart to do it is what I have to do then so be it. I'm after an inconspicuous fix.

A resistor can be added in series with the circuit to avoid having to disassemble the cluster. You could potentially cut into where the signal routes through Connector BA1 under the hood, but it would be easier to add the resistor at the connector entering the cluster. You would cut the gray wire in position 14 and add a resistor between the cut wire. I would start at about 1K Ohms and go up from there to find a desirable brightness.

Conn D2.jpg
birdmanThread starterUSA · Sep 30, 2009#21
Thanks for the info but I'll need a bit more clarification to understand the lingo. What is a cluster? Where under the hood is position I4 and what does that diagram mean? I don't see anything with a BA1 on the diagram. I don't even know where this electrical block is located. Has anyone done a step by step pictorial on this yet?
birdmanThread starterUSA · Sep 30, 2009#22
I posted this already in another section. Being new I'm still trying to find my way around. After long night drives I find the high beam indicator light a bit too bright and I want to reduce it a bit. I drive in remote areas where there is lots of game that I want to avoid hitting so I need the brights on. Has anyone submitted a step by step pictorial on how to add a resister? One member said there was a way to do it under the hood (bonnet) instead of disassembling the dash. The suggestion I got was very thoughtful but way over my head. I'm not afraid to do it myself but I'll have to be led through this one in layman terminology. Thanks.:eyebulge
CTScottUSA, CT · Sep 30, 2009#23
Originally Posted by birdman ↑
Thanks for the info but I'll need a bit more clarification to understand the lingo. What is a cluster? Where under the hood is position I4 and what does that diagram mean? I don't see anything with a BA1 on the diagram. I don't even know where this electrical block is located. Has anyone done a step by step pictorial on this yet?
BA1 is a terminal block within the fuse box under the hood. The place where the resistor would need to be added is on a connector that is under the fuse box, so it would be easier to pop off the trim around the cluster (also known as the combination meter, speedometer, etc.) and make the connection where the wire enters one of the two connectors (connector D2 pictured above) going into it.

Here's a picture of connector D2. Wire 14 is the gray wire third from the left on the bottom row:
CM - Conn D2.jpg

Here is the annoying indicator before modification:
CM - Before.jpg

And, here it is after adding a 2K resistor inline with the gray wire:
CM - After 2K.jpg

Both pictures were snapped with the same camera settings. You can see how the before picture has a glowing halo around the indicator and the second is illuminated, but no where near as much as the before pic.
AlexNet0Rockland, ME · Sep 30, 2009#24
instead of starting a new thread, you should PM tk-421 and ask him to move the other thread here.

the suggestions you got from CTScott are the best I believe you are going to get.

If you would like me to elaborate on the cluster method (the cluster is the circuit board where the speedometer and indicator lights are) then I will post again later.
severous01SE Texas · Sep 30, 2009#25
turn your brightness knob down. it'll dim all lights on dash
CTScottUSA, CT · Sep 30, 2009#26
Originally Posted by severous01 ↑
turn your brightness knob down. it'll dim all lights on dash
The indicators don't dim, just the speedometer and fuel gauge dim.
birdmanThread starterUSA · Sep 30, 2009#27
I'm new at computers and don't have a clue what a PM tk-421 is. CTScott is very smart. I just read his tire pressure warning light shut off switch install. Actually this post is the new improved version of the other. I will send him a message. Thank you. Yarisworld rocks!
CTScottUSA, CT · Sep 30, 2009#28
Originally Posted by birdman ↑
I'm new at computers and don't have a clue what a PM tk-421 is. CTScott is very smart. I just read his tire pressure warning light shut off switch install. Actually this post is the new improved version of the other. I will send him a message. Thank you. Yarisworld rocks!
Look at the last post of the other one. I did a quick test with pics for you.
birdmanThread starterUSA · Sep 30, 2009#29
Thanks Alex. I want to avoid the circuit board approach if possible. Way beyond my comfort zone. I may end up applying a black dot on the plastic shield if it comes to it.
birdmanThread starterUSA · Sep 30, 2009#30
CTScott you rock!
birdmanThread starterUSA · Sep 30, 2009#31
Marcus, At the end of the day I might just do it. Thanks man.
birdmanThread starterUSA · Sep 30, 2009#32
CTScott you are too much man. You must possess an extra chromosome or something. When you spliced the gray wire was the gauge assembly still in the car? If not How do you remove it? Do you have a photo of the 2k resister in place? Does it need soldering? Does it matter which end of the resister is closest to the D2 connecter?
CTScottUSA, CT · Sep 30, 2009#33
Originally Posted by birdman ↑
CTScott you are too much man. You must possess an extra chromosome or something. When you spliced the gray wire was the gauge assembly still in the car? If not How do you remove it? Do you have a photo of the 2k resister in place? Does it need soldering? Does it matter which end of the resister is closest to the D2 connecter?
I tested it out on Crashy (my ebay purchased totaled Yaris), who has no headlights, so i actually jumped power to the indicator to make it light and then added the resistor inline with the jumper. I also have her dash completely removed, so I have easy access to all wiring.

But, to do this on an intact car, you pop the cluster trim, disconnect the connector, and then cut the resistor into the wiring harness. You'll cut the wire (about 2" from the connector to give yourself room to work), strip both ends, attach one end of the resistor to each (resistors aren't polarized, so it doesn't matter which end goes to which), and then either heat shrink it or tape it up.
bronsinnj · Sep 30, 2009#34
Hmmm very interesting and Ive learned something here. Still wouldnt it make a lot more sense to put a piece of colored tape over the high beam indicator rather than take everything apart and all?
birdmanThread starterUSA · Sep 30, 2009#35
Thanks CT. I have one more question regarding this fix. Can you get crimp-on resisters or must they be soldered?
birdmanThread starterUSA · Sep 30, 2009#36
There is yet another question. What gauge wire will the resister be spliced into?
CTScottUSA, CT · Sep 30, 2009#37
You can't get crimp on resistors, but you can crimp them onto the wire (I believe it is 22 AWG) with butt splices.
birdmanThread starterUSA · Sep 30, 2009#38
Would a 1 or 1.5k resister do?
birdmanThread starterUSA · Sep 30, 2009#39
You have been very patient guiding me along to the point where I am confident enough to do this fix. Thank you thank you!
CTScottUSA, CT · Sep 30, 2009#40
Originally Posted by birdman ↑
Would a 1 or 1.5k resister do?
Try the 1.5K, if that's what you have on hand. I tried 1k initially and then moved up to 2k. Even with a 10K resistor it will still illuminate.
birdmanThread starterUSA · Sep 30, 2009#41
I just noticed that the diagram of the connector has "11" 3rd from the left while the photo shows the gray wire in what appears to be the 11 position not the 14th. Why is that?
birdmanThread starterUSA · Sep 30, 2009#42
Is the higher number resister dimming the light more?
birdmanThread starterUSA · Sep 30, 2009#43
I cant imagine where CT gets the energy to keep up with all the questions coming up. CT deserves a medal.
CTScottUSA, CT · Sep 30, 2009#44
The 11 vs 14 thing is because the connector drawings are from the perspective of looking into the end of the connector. In the picture we are looking into the back, so the pin numbers are mirrored.

A higher value resistor does dim it more.
birdmanThread starterUSA · Sep 30, 2009#45
If I wanted to dim it down to a point where it's still easy enough to see during the day if the high beams are mistakenly left on what is highest number resister you'd use?
CTScottUSA, CT · Sep 30, 2009#46
I'd say 10K max.
birdmanThread starterUSA · Sep 30, 2009#47
So thats what you'd personally use?
birdmanThread starterUSA · Sep 30, 2009#48
I have a feeling we're reaching conclusion any time now.
jambo101Montreal Canada · Oct 1, 2009#49
Why not just cut out a little square of duct tape or electricians tape and stick it over the blue light.
CTScottUSA, CT · Oct 1, 2009#50
Originally Posted by birdman ↑
So thats what you'd personally use?
I am going to do this on my 09, when I have a chance, and will probably use somewhere between a 2K and 5K resistor.