Replies continued
KioshiFremont, CA · Oct 15, 2009#151you should be able to get a tracking number option when shipping from any country....just have to tell the original sender or the second (in this case, Mad Dog)...i used tracking to ship to CTScott just because I dont trust the assholes at the post office....$15 tops...
International shipping should be at most $35-$40 tops, as I have shipped an expensive item to a friend in Japan to her obscure house address... and package got to her within a week :)
*MAD DOG*Victoria, Australia · Oct 15, 2009#152 Originally Posted by
Lewis ↑ Never got one from Maddog......not sure if it was available.
Tracking was available, but it was another $20. I sent it registered post and have my receipt. There is a barcode on the receipt.
LewisThread starterNJ · Oct 15, 2009#153The pot will boil when we stop watching it Kioshi.
:-)
Before too long poor CTScott will be struggling with both our our clusters!
spookzSydney, Australia · Oct 15, 2009#154Does the AUDM digital cluster get the 'Auto-Dimming' as well? I don't think I've noticed it before. Let me go and try. So I'm assuming there's a light sensor installed somewhere for the the auto-dimming to work?
advocatelocation · Oct 15, 2009#155I have to agree that seeing CTScott's awesome knowledge makes me envious I didn't finish my electrical engineering degree.
Ah well Software is more my style anyways =)
Can't wait to see the results on kioshi's and lews' clusters!! wooooooooooo!
BTW i think it's time for a new bagel update Lewis.
CTScottUSA, CT · Oct 15, 2009#156 Originally Posted by
spookz ↑ Does the AUDM digital cluster get the 'Auto-Dimming' as well? I don't think I've noticed it before. Let me go and try. So I'm assuming there's a light sensor installed somewhere for the the auto-dimming to work?
It auto dims when the headlights are switched on if you enable that mode. It doesn't do smart dimming with a light sensor.
*MAD DOG*Victoria, Australia · Oct 15, 2009#157Scott,
When you get the Oz Cluster you will notice that it has a display area that says what gear your in, mpg, distance to empty, etc. But for some reason it's not switched on or does not seem to work here. If you could figure out a way (i'm sure you can) to make that stuff work that would be fantastic.
LewisThread starterNJ · Oct 16, 2009#158Bagel update- no package from Oz (if you're married you know there are ALWAYS packages :-) ).
It's only been a week and Tony said the post office down there told him up to 3 weeks time so let's all try to be patient. It might take Scott a bit of time to get to it too- remember he just might have things like work, family etc. to attend to before he can get to his and our hobby projects.
We'll get there - as soon as is feasible- I promise.
Lew
jounabayamon puerto rico · Oct 16, 2009#159 Originally Posted by
Lewis ↑ Bagel update- no package from Oz (if you're married you know there are ALWAYS packages :-) ).
u got that right 🍻
CTScottUSA, CT · Oct 16, 2009#160 Originally Posted by
*MAD DOG* ↑ Scott,
When you get the Oz Cluster you will notice that it has a display area that says what gear your in, mpg, distance to empty, etc. But for some reason it's not switched on or does not seem to work here. If you could figure out a way (i'm sure you can) to make that stuff work that would be fantastic.
Interesting. So, Oz cars don't get MPG. I wonder if EU cars with the digital display do?
Can you give me the part number off of your ECM? I have a feeling that the MPG is calculated by the ECM and is sent to the cluster.
*MAD DOG*Victoria, Australia · Oct 16, 2009#161 Originally Posted by
CTScott ↑ Interesting. So, Oz cars don't get MPG. I wonder if EU cars with the digital display do?
Can you give me the part number off of your ECM? I have a feeling that the MPG is calculated by the ECM and is sent to the cluster.
Ummmmm WTF is ECM? Sorry i'm not a tech head. As for the part number of this ECM where would I find that?
Also over here it would be Kilometers to the litre Km/L as opposed to Miles Per Gallon MPG.
I'm off to bed now as it's Saturday 17/10/2009 1:06 AM.
CTScottUSA, CT · Oct 16, 2009#162 Originally Posted by
*MAD DOG* ↑ Ummmmm WTF is ECM? Sorry i'm not a tech head. As for the part number of this ECM where would I find that?
Also over here it would be Kilometers to the litre Km/L as opposed to Miles Per Gallon MPG.
I'm off to bed now as it's Saturday 17/10/2009 1:06 AM.
The ECM (or ECU) is the main computer. It is mounted to the firewall, under the hood and has two huge connectors plugged into it. The part number is on a sticker. In this picture you can see ECM with its part number sticker (and one of the connectors unplugged):

spookzSydney, Australia · Oct 17, 2009#163I forgot where I read it.. possibly in the manual. But the MPG display only works with South African models. There must be a module which we don't get in Australia.
LewisThread starterNJ · Oct 17, 2009#164Update- not in Saturday's mail
:-(
KioshiFremont, CA · Oct 17, 2009#165:(
What method was it sent through? I forget, if mentioned previously....
LewisThread starterNJ · Oct 17, 2009#166ordinary certified post Kioshi......week one is done- there could possibly be two more weeks to go according to what Tony was told
:-((((((
*MAD DOG*Victoria, Australia · Oct 18, 2009#167 Originally Posted by
CTScott ↑ The ECM (or ECU) is the main computer. It is mounted to the firewall, under the hood and has two huge connectors plugged into it. The part number is on a sticker. In this picture you can see ECM with its part number sticker (and one of the connectors unplugged):
Attachment 29201
Scott,
I've forgotten to look at the part number but will do so tomorrow.
But I have found a good quality picture of what I was talking about....
Oz Cluster
See what I mean by it should display those things but it does not.
*MAD DOG*Victoria, Australia · Oct 19, 2009#168Here are all the numbers on the ECU
89661-52C30
212000-2230 12V
2012230A
Here is a pic of the Oz ECU. It was behind the battery on the firewall.
advocatelocation · Oct 19, 2009#169Good lookin Mad Dog! CTScott is gonna need the part numbers to do RND to see if we can get the gear indicator and MPG to work.
CTScottUSA, CT · Oct 19, 2009#170 Originally Posted by
*MAD DOG* ↑ Here are all the numbers on the ECU
89661-52C30
212000-2230 12V
2012230A
Here is a pic of the Oz ECU. It was behind the battery on the firewall.
Very interesting. The 89661-52C30 ECM is specific to the Australian market on NCP91R-AGPRKQ and NCP91R-AHPRKQ (3 door and 5 door automatics). I forgot that on RHD cars that they hide the ECM behind the battery.
LewisThread starterNJ · Oct 19, 2009#171UPDATE-
The box arrived to NJ today and is on it's way to CTScott.
.......now the next chapter?
KioshiFremont, CA · Oct 19, 2009#172wow, mailed it that fast to Scott huh...
Next chapter is always interesting..... ;)
LewisThread starterNJ · Oct 19, 2009#173 Originally Posted by
Kioshi ↑ wow, mailed it that fast to Scott huh...
Next chapter is always interesting..... ;)
yes Kioshi we have certainly gave Scott some challenges!
*MAD DOG*Victoria, Australia · Oct 19, 2009#174So glad it arrived. Now it's all up to Scott to weave some magic :)
KioshiFremont, CA · Oct 19, 2009#175I have a feeling since you have an 09 w/ ABS, your cluster will be an easy swap...lol
I looked at Mad Dog's hi res pics in the previous page and you too have the ABS icon and stuff.....so no problem with that ;)
I love it when I end up w/ complications in life..
CTScottUSA, CT · Oct 19, 2009#176 Originally Posted by
Kioshi ↑ I have a feeling since you have an 09 w/ ABS, your cluster will be an easy swap...lol
I looked at Mad Dog's hi res pics in the previous page and you too have the ABS icon and stuff.....so no problem with that ;)
I love it when I end up w/ complications in life..
Lewis mentioned an interesting dilemma with it; The connectors are on opposite sides, so the cables won't reach.
KioshiFremont, CA · Oct 19, 2009#177Thats something I didn't catch in the photos from Mad Dog. The only thing I can think of for that at the moment would be do find a salvaged Yaris and cut the wires off that, unless the same gauge wires can be spliced and soldered onto the ones on the connector.
CTScottUSA, CT · Oct 19, 2009#178 Originally Posted by
Kioshi ↑ Thats something I didn't catch in the photos from Mad Dog. The only thing I can think of for that at the moment would be do find a salvaged Yaris and cut the wires off that, unless the same gauge wires can be spliced and soldered onto the ones on the connector.
I'll fire it up on the bench first and then to run it in Crashy, I'll have to splice an extra foot onto each wire.
LewisThread starterNJ · Oct 20, 2009#179yes Scott -the humor of this situation can help offset the extra work involved for you regarding the cables.
imagine if everything is inverted like the cables- for instance the speed would go down on the speedometer as you go faster etc.!
I know i bit off more than i can chew with the OZ cluster- luckily we have somebody here with very sharp teeth- Scott!
p.s. they say water goes down the drain anti-clockwise in OZ- perhaps that was a warning!
KioshiFremont, CA · Oct 20, 2009#180😆😆
Gotta love the people here.
CTScottUSA, CT · Oct 21, 2009#181Update: I received the OZ cluster from Lewis today!
I immediately had to open the box and hook it up on Crashy. With the swapped connectors (since it is for a RHD Yaris) I just hooked up connector D1, which has power, CAN bus, fuel gauge, tach, speed, etc (the other just has the feeds for a bunch of the indicator lights).
It powered up fine and the fuel gauge showed proper level. So, I started the car and the tach worked correctly, but the speedometer stayed at zero. This cluster is off an ABS car, so that makes sense, as Crashy is non-ABS.
The issue though is that the cluster is indeed angled to... the passenger (at least on this side of the world). The VFD (vacuum fluorescent display) is reversed and is mounted in that chunk at the bottom and is pointed to the left. A concave mirror magnifies and inverts the VFD and angles the display to the USDM passenger.
Being an Engineer, I just had to take it apart to see how it was setup and to snap some pics. Here they are:
Powered up:
Close up of the VFD:
Close up of the clock/mileage VFD:
Concave mirror:

1NZYaris1New Zealand · Oct 21, 2009#182So could you transplant the guts of the aussie cluster , into the USDM
unit , or is it not that easy 😆
CTScottUSA, CT · Oct 21, 2009#183 Originally Posted by
1NZYaris1 ↑ So could you transplant the guts of the aussie cluster , into the USDM
unit , or is it not that easy 😆
The USDM one is just a flat plane. The Aussie one has the lens in the same place, but the guts and case are completely different to make the VFD work correctly. I was initially thinking that you could modify the bottom chunk and the back to point towards the left, but the upper portion has a molded tunnel that is angled from left to right. It would take some creative plastic work to make the display point left.
*MAD DOG*Victoria, Australia · Oct 21, 2009#184Scott and Lewis,
Glad it works. Looks like some more work is required to make it useable for you though.
Scott,
I know you just got the unit, but is there any chance of a fix so the Km/L would work for us Aussies?
Attached picture not available
*MAD DOG*Victoria, Australia · Oct 21, 2009#185I think this picture sums up this thread.
:)
CTScottUSA, CT · Oct 21, 2009#186 Originally Posted by kustom play ↑
bummer it doesnt work
so how does it look from the driver side? not well or is it kinda tolerable?
well back to looking for a USDM S Cluster
Without modification the speedometer/tach portion are really not viewable at all from the driver's side.
KioshiFremont, CA · Oct 22, 2009#187sedan cluster should be the same size as the liftback cluster, but the plugs to connect are different from the liftback......
Also.....is your car ABS enabled kustom? If not, you will run into problems like Lewis and I.... :P
KioshiFremont, CA · Oct 22, 2009#188I have someone on here who is test fitting a 09 w/ ABS cluster on his 07 non-ABS car....I'll let you know whether it works or not..
But: 08 w/ ABS accepted my RS cluster.
Scott's 08 w/o ABS didnt accept it His 09 with ABS did...
So i highly doubt yours would accept a cluster w/ a tach...speed data won't be sent the same way like it is through the speedometer only cluster~ jus saving you the trouble and money...
But go for it, we already have 2 other guinea pigs on here hahaha
LewisThread starterNJ · Oct 22, 2009#189CTScottUSA, CT · Oct 22, 2009#190 Originally Posted by kustom play ↑
so it looks like its a bust for LHD cars then :(
so looks like the only way to get a tachometer and speedo is the get the USDM tach/speedo combo then
Scott, Anyway to rig up a sedan cluster? How far off is the fit?
I always see those for sale and there super cheap!
The sedan cluster may (?) be the same size, but it mounts differently. It's mounting screws are out on the ends, rather than out in front. The right connector is the same (pinout and all). The left is a wider connector, but the pin functions are identical.
CTScottUSA, CT · Oct 22, 2009#191 Originally Posted by kustom play ↑
so maybe it would fit if we could find a way to mount it?
but would it have the issues with the read outs? like say an 07 sedan with an 07 liftback?
I was just looking at sedan cluster pictures on ebay and the sedan one is a very different shape than the LB one.
CTScottUSA, CT · Oct 22, 2009#192 Originally Posted by kustom play ↑
ok get back to making the tach fit the clock area
I'm making good progress on it.
KioshiFremont, CA · Oct 22, 2009#193 Originally Posted by kustom play ↑
ok get back to making the tach fit the clock area
so demanding....lol
I wonder if the OZ cluster will have odo adjusting problems like my RS cluster....?
CTScottUSA, CT · Oct 22, 2009#194 Originally Posted by
Kioshi ↑ so demanding....lol
I wonder if the OZ cluster will have odo adjusting problems like my RS cluster....?
I hooked it up to my test bench last night and had the same result with making the speedo change but the odo didn't increment. I just need to get to the bottom of the extra bytes in the speed message.
KioshiFremont, CA · Oct 22, 2009#195 Originally Posted by
CTScott ↑ I hooked it up to my test bench last night and had the same result with making the speedo change but the odo didn't increment. I just need to get to the bottom of the extra bytes in the speed message.
Did your 09 send any additional messages from my RS cluster that could help you out with that? I know you said you were going to try that out in my thread...dont know~
CTScottUSA, CT · Oct 22, 2009#196 Originally Posted by
Kioshi ↑ Did your 09 send any additional messages from my RS cluster that could help you out with that? I know you said you were going to try that out in my thread...dont know~
My 09 sent the same data to both its own cluster and to your RS cluster. It's entirely possible that the odo increment data is sent in an entirely different message. I have 11 more messages from the 09 data capture to decipher.
LewisThread starterNJ · Oct 23, 2009#197Scott - what about starting a new thread keeping us informed on the progress and release of the Yargauge? It seems like the best answer for so many of us who want a tach but within the confines of the existing OEM cluster setup (i.e. not a separate tachometer on the dash and don't want to have to mess with the odometer flashing.
This thread on the OZ cluster is about as dead as a doornail.
*MAD DOG*Victoria, Australia · Oct 23, 2009#198 Originally Posted by
Lewis ↑ This thread on the OZ cluster is about as dead as a doornail.
Maybe for you but not for me. I'm hoping Scott can figure out a way to make the Km/L and gear display work.
LewisThread starterNJ · Oct 23, 2009#199sorry Tony- my mistake in wording- I just meant that for all the folks looking for a tach in the cluster it was dead- not dead for everyone.
CTScottUSA, CT · Oct 23, 2009#200 Originally Posted by
Lewis ↑ Scott - what about starting a new thread keeping us informed on the progress and release of the Yargauge? It seems like the best answer for so many of us who want a tach but within the confines of the existing OEM cluster setup (i.e. not a separate tachometer on the dash and don't want to have to mess with the odometer flashing.
This thread on the OZ cluster is about as dead as a doornail.
The YarGauge has its own thread that I update.
Lewis, If you don't mind I'll attempt to make the necessary modifications to make the OZ cluster visible to the USDM driver.