Yarisworld Archive

Racerfreak's Suspension

129 posts · 30,455 views · page 1 of 3

RacerFreakXXXOriginal postSomers NY · Sep 8, 2009#1
This is what I have so far, I have had my springs for a while but wanted to wait for my sway bar before I installed them. I have everything now and will be installing them sometime in the next week or two. So far I have AOE TigerTech lowering springs and Ultra Racing 23mm rear sway bar. I'll keep an update on how the springs and the sway bar compare. I measured a 3" gap on my front tire and 3.5" gap on my rear tire. This isn't 100% accurate but I know I'm only of by 1/4 of an inch give or take.

Picture not included in this copy

Replies 128

TamagoOff Grid · Sep 8, 2009#2
best measurement is from the ground up, not from the tire to the fender.

looks like you have half a start to a decent suspension. get some struts and shocks before you install those springs
AdeJong 03LA, CA · Sep 8, 2009#3
Originally Posted by Tamago ↑
best measurement is from the ground up, not from the tire to the fender.

looks like you have half a start to a decent suspension. get some struts and shocks before you install those springs
+2349057809345

or else youre gonna have to the exact same thing again to install the struts. HUGE waste of time and money

lookin good so far though!
RacerFreakXXXThread starterSomers NY · Sep 8, 2009#4
Are you kidding, I got quoted at $300-700 from shops to install springs. I'm gonna install them myself, just gonna rent some spring compressors and I have a few mechanic friends who said they would lend me their garage and tools and help. Oh and I'm not buying shocks because I'm going to buy coilovers, these are just for the next year or two.
TamagoOff Grid · Sep 8, 2009#5
you don't need a spring compressor :)

make sure to take off your wiper tray, it'll make those front struts so much easier!
MUSKOKA800Chatham, Ontario, Canada · Sep 9, 2009#6
To simplify the process, install the swaybar only after changing out both rear springs.
And yes, without upgrading the dampers and depending on the rates of the new springs you do run the risk of pogoing down the road, ultra-rice style.
SpeedjunkiejpJacksonville, FL · Sep 9, 2009#7
Like Tamago said, a spring compressor is not needed going from stock to lowered. the springs are shorter and will not need compressing to put the top hat on. Taking the top hat off just use air gun and stand back LOL. This is the funnest part IMO to installing springs.
detroiterMetro Detroit · Sep 9, 2009#8
I'm running AOE TigerTecs, UR 23mm rear sway bar and Tokico Blues. Your going to LOVE the setup if you throw on the shocks as well. Be careful though, you might start eating through tires from having way too much fun once you learn how it handles ;)
MUSKOKA800Chatham, Ontario, Canada · Sep 9, 2009#9
Originally Posted by Speedjunkiejp ↑
Like Tamago said, a spring compressor is not needed going from stock to lowered. the springs are shorter and will not need compressing to put the top hat on. Taking the top hat off just use air gun and stand back LOL. This is the funnest part IMO to installing springs.

I chose to spend $30.00 (on sale) for a quality compressor and keep my teeth intact. 😁
TamagoOff Grid · Sep 9, 2009#10
Originally Posted by MUSKOKA800 ↑
I chose to spend $30.00 (on sale) for a quality compressor and keep my teeth intact. 😁
you can rent them for free from your local auto parts store.
kngrsllSpartanburg, SC · Sep 9, 2009#11
if you buy good struts, you wont need coilovers in a year.

what is the advantage to getting coilovers in a year?
TamagoOff Grid · Sep 9, 2009#12
Originally Posted by kngrsll ↑
if you buy good struts, you wont need coilovers in a year.

what is the advantage to getting coilovers in a year?
agreed. no one ever adjusts them 'for height' like they think they will. set it and forget it.

a cheap set of coilovers (ksport, megan, tein basic) will have struts that are similar to garbage, whereas buying a nice set of tokicos (or in my case, thank you Ken, koni yellows) puts you in premium strut-land.


if you're buying coilovers just to buy coilovers, you might as well buy some KW V3's lol
kngrsllSpartanburg, SC · Sep 9, 2009#13
Originally Posted by Tamago ↑
agreed. no one ever adjusts them 'for height' like they think they will. set it and forget it.

a cheap set of coilovers (ksport, megan, tein basic) will have struts that are similar to garbage, whereas buying a nice set of tokicos (or in my case, thank you Ken, koni yellows) puts you in premium strut-land.


if you're buying coilovers just to buy coilovers, you might as well buy some KW V3's lol
and if you are getting blues, i would buy xD blues, they have got to be stiffer. i love my tokicos, they beat the hell out of me lol
RacerFreakXXXThread starterSomers NY · Sep 9, 2009#14
for coilovers I was considering silk road, cusco zero-one, or tein super compact if i could get my hands on some. You are right I may like it better with struts but i want to have .5 clearance.

Why do a lot of people act like i'll blow a strut within the first month of having them on stock struts? I thought there were plenty of people out there with springs on stock struts for a year plus?
AdeJong 03LA, CA · Sep 10, 2009#15
Originally Posted by RacerFreakXXX ↑
for coilovers I was considering silk road, cusco zero-one, or tein super compact if i could get my hands on some. You are right I may like it better with struts but i want to have .5 clearance.

Why do a lot of people act like i'll blow a strut within the first month of having them on stock struts? I thought there were plenty of people out there with springs on stock struts for a year plus?
i think youll realize that you wont really want to spend the money on coils once you get a correctly set up spring/shock/strut combo

youre not gonna enjoy the full effects of getting springs if this is just a temporary fix

why do you want coils? for height adjustment?
detroiterMetro Detroit · Sep 10, 2009#16
We are all suggesting you get the Tokicos or a performing shock/strut because your better off doing it right the first time around and not half assing it, since you already have some good springs and rear sway bar to throw on. Trust me, if you get the Tokico shocks/struts, you'll have the same exact set up that I'm running and you WON'T be sorry. Ever wonder what it's like to piss off some people with some more "expensive, sporty" cars in the turns? You'll find out soon enough if you go with upgrading the shocks/struts as well.
AdeJong 03LA, CA · Sep 10, 2009#17
Originally Posted by detroiter ↑
We are all suggesting you get the Tokicos or a performing shock/strut because your better off doing it right the first time around and not half assing it, since you already have some good springs and rear sway bar to throw on. Trust me, if you get the Tokico shocks/struts, you'll have the same exact set up that I'm running and you WON'T be sorry. Ever wonder what it's like to piss off some people with some more "expensive, sporty" cars in the turns? You'll find out soon enough if you go with upgrading the shocks/struts as well.
+1

i could already do it stock. now i dont have to try as hard LOL
RacerFreakXXXThread starterSomers NY · Sep 10, 2009#18
Yea, for $320 shipped you really can't go wrong, maybe I can hold off a bit for the shocks... however I am going to get coilovers for maily being able to change dampening rates. Does anyone know exactly what you reuse on the stock struts? I may just buy those parts so I can swap my stock suspension in for winter.
Kaotic LazagnaCentral Valley, CA · Sep 10, 2009#19
Yeah, I like my TRD shocks/S.Tech springs combo. But like I've said, I can really use a rear sway bar.
MUSKOKA800Chatham, Ontario, Canada · Sep 10, 2009#20
Originally Posted by Tamago ↑
you can rent them for free from your local auto parts store.

True, but my local stores tool was damaged and with no replacement on the horizon.
So for a measly $30.00 I have the tool inhand and can do the job at my leisure, not just when it's available (often booked out). Plus now I have it to share with other local enthusiasts.
TamagoOff Grid · Sep 10, 2009#21
yes, it's useful if you're working on cars other than yarii, but it's completely unnecessary when installing lowering springs 😁
scapeBeaufort, South Carolina · Sep 10, 2009#22
is there any benefit to upgrading the shocks without getting new springs? I'm not sure I want to lower my car, I practically bottom out in and around town; and sometimes go off road; but want a bit of finer touch on the handling
TamagoOff Grid · Sep 10, 2009#23
Originally Posted by scape ↑
is there any benefit to upgrading the shocks without getting new springs? I'm not sure I want to lower my car, I practically bottom out in and around town; and sometimes go off road; but want a bit of finer touch on the handling
absolutely, upgrading struts/shocks with stock springs will handle BETTER than a yaris on lowering springs and stock struts/shocks :)
LafiroNYC · Sep 10, 2009#24
Alright, so I am a victim of stock shocks/struts ( Which are dead now ), but I have TRD springs installed.

So what should I do for a good ride, quality? Change my springs? Or keep them and get the Tokico Blues?
TamagoOff Grid · Sep 10, 2009#25
if you like the drop, keep the springs you have. definitely get some up-rated shocks/struts

kyb GR2's are another good-yet-cheap alternative to stock struts.

around $220 + shipping from tirerack
LafiroNYC · Sep 11, 2009#26
I like the drop, a LOT.
I like the handling, I just don't like how rough they are. I was wondering if I changed them to NF210's, and some Tokico shocks, maybe it would be better, or thats just a bad combination. If so, I will just go ahead and purchase the Tokico's and keep the TRD's I have now.

Its that the streets here in NYC, SUCK. So many bumps, and potholes. Unfixed for years in lots of locations that people drive through everyday unfortunately.

I would just want the car to remain on the floor, and not allow the tires to bounce off the floor causing jolts to go through the car, and slight loss of traction while in turns(highway speed), especially on wet floors.
largeorangefontSo Cal, OC · Sep 11, 2009#27
Don't waste your money with NF210s, they are about the same rate and height as TRD springs. You will but them on and feel no difference.

You can get KYB GR2s if you want a stock replacement, or get the Tokico Blues if you want something a bit stiffer.

Originally Posted by Lafiro ↑
I like the drop, a LOT.
I like the handling, I just don't like how rough they are. I was wondering if I changed them to NF210's, and some Tokico shocks, maybe it would be better, or thats just a bad combination. If so, I will just go ahead and purchase the Tokico's and keep the TRD's I have now.

Its that the streets here in NYC, SUCK. So many bumps, and potholes. Unfixed for years in lots of locations that people drive through everyday unfortunately.

I would just want the car to remain on the floor, and not allow the tires to bounce off the floor causing jolts to go through the car, and slight loss of traction while in turns(highway speed), especially on wet floors.
RacerFreakXXXThread starterSomers NY · Sep 11, 2009#28
detroiter do you have any pics of your car with the springs and struts? I'd love to see what it looks like.
kngrsllSpartanburg, SC · Sep 11, 2009#29
it will look the same with struts... the ride height wont change.
frownonfunRGV, Texas · Sep 11, 2009#30
Originally Posted by Tamago ↑
yes, it's useful if you're working on cars other than yarii, but it's completely unnecessary when installing lowering springs 😁
can you stop saying compressors are completely unnecessary. they are a safe way to get the stock spring off the stock strut. not sure how that is unnecessary. were u able to do it without hurting yourself? maybe. but that doesn't make it safe.
detroiterMetro Detroit · Sep 12, 2009#31
Originally Posted by RacerFreakXXX ↑
detroiter do you have any pics of your car with the springs and struts? I'd love to see what it looks like.


I'll take a couple for you tomorrow morning. Supposed to be a nice sunny day so shouldn't be a problem :)
TamagoOff Grid · Sep 12, 2009#32
Originally Posted by frownonfun ↑
can you stop saying compressors are completely unnecessary. they are a safe way to get the stock spring off the stock strut. not sure how that is unnecessary. were u able to do it without hurting yourself? maybe. but that doesn't make it safe.
i've done at least 40 spring installs without a spring compressor and NEVER been injured.

my technique is simple, safe, and saves time over monkeying around with compressors.

by the way i own a spring compressor set, and do use it when necessary, but it's simply not needed on a car as light as the yaris.
kngrsllSpartanburg, SC · Sep 12, 2009#33
I have gotten away with it too. I have had some hairy moments with out one (ie strut ended up about 30 feet away 😲 lol) but in general, you dont need one.
detroiterMetro Detroit · Sep 12, 2009#34
RacerFreak....Here's those pics I promised you I'd take this morning.

Aoe TigerTec Springs, Tokico Blue shocks/struts, Ultra Racing 23mm Sway bar

Like I said, it's a very tasteful drop. It's not a 4x4 and it's not slammed either.
I'm very pleased with the springs and matched up with the Tokicos and UR sway bar,
it's a killer combination. I really do suggest you just getting the shocks so you can
do it right the first time and make it that much better as well.

Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
RacerFreakXXXThread starterSomers NY · Sep 12, 2009#35
your car looks great thank you. I'm kinda debating about getting rid of the springs now and getting bc coils... but I have to really think about it.
detroiterMetro Detroit · Sep 12, 2009#36
In all honesty, like a few other stated as well, you more than likely will just set the coilovers on a setting and never change them again. It's a lot of money to spend on something you might only mess with very sparingly. Before spending alot of money on coilovers, I HIGHLY suggest you spend the $300, which is nothing compared to a decent set of coilovers, see how you like the setup (of which I'm sure you would love it!) before spending that kind of amount.
AdeJong 03LA, CA · Sep 13, 2009#37
Originally Posted by frownonfun ↑
can you stop saying compressors are completely unnecessary. they are a safe way to get the stock spring off the stock strut. not sure how that is unnecessary. were u able to do it without hurting yourself? maybe. but that doesn't make it safe.
i just did my suspension the other day and it came off completely fine. i rented a spring compressor and it ended up being a complete waste of time (not money since rental is free)
regalPA · Sep 13, 2009#38
Originally Posted by detroiter ↑
In all honesty, like a few other stated as well, you more than likely will just set the coilovers on a setting and never change them again. It's a lot of money to spend on something you might only mess with very sparingly. Before spending alot of money on coilovers, I HIGHLY suggest you spend the $300, which is nothing compared to a decent set of coilovers, see how you like the setup (of which I'm sure you would love it!) before spending that kind of amount.

Are there springs available with rates as high as coilovers? I wish my TRD springs were stiffer, but don't know that my Tokico Blues could handle a stiffer spring. Looking back, I think coilovers may make a lot of sense for the Yaris.
detroiterMetro Detroit · Sep 13, 2009#39
Well as far as I know, the AOE TigerTec springs are the hightest spring rate available right now for lowering springs, not comparing to coilovers. The TigerTecs are 4k front and 3k in the rear. From my guess, they are a great bit stiffer than the TRD springs. Anyone care to chime in that knows for sure?
LafiroNYC · Sep 13, 2009#40
I wonder if there is any way to modify that torsion beam? in the back of our cars so that we can cut it in the middle, and attach it to the car in some other fashion. This way we get truely independant rear suspension. It has always been a thought. ugh the amount of stuff I want to do to my car is rediculous. I can't keep thinking at about this stuff lol.
rob323Joyner, Brisbane · Sep 13, 2009#41
Originally Posted by Lafiro ↑
I wonder if there is any way to modify that torsion beam? in the back of our cars so that we can cut it in the middle, and attach it to the car in some other fashion. This way we get truely independant rear suspension. It has always been a thought. ugh the amount of stuff I want to do to my car is rediculous. I can't keep thinking at about this stuff lol.
Not easily due to the pivot point being located infront of the beam. You may as well fabricate a whole new rear beam setup from scratch instead.
frownonfunRGV, Texas · Sep 13, 2009#42
Originally Posted by AdeJong 03 ↑
i just did my suspension the other day and it came off completely fine. i rented a spring compressor and it ended up being a complete waste of time (not money since rental is free)
ok fair enough. i just don't think everyone necessarily knows what they are doing if it's their first time doing this. and plus since they are free and take less than 5 mins to put on i don't see the harm in using them. but if you guys are absolutely sure no one could ever possibly hurt themselves taking off the yaris stock springs then i'll shut up. i just personally would never count out the possibility.
lilredrocketDFW, Texas · Sep 13, 2009#43
Racer. You said you were thinking about getting coils. Do you want them for adjusting the Dampning of the shocks if so them look the the Tokico HTS shocks and struts more than the standard pair but worth it too!!
TamagoOff Grid · Sep 13, 2009#44
independant rear trailing arm is still garbage. it serves no purpose, and the fact that you'd have to put a big F.U. rear swaybar, so you're not independant anymore anyway. your alignment problems associated with trailing arm still exist.

add that to the extra weight required to pull it off and you've just done a pointless mod.

edit:

Volkswagen rabbit/gti is the godfather of the trailing arm rear suspension. if VW could have improved on it by now, they would have. the R32 rear suspension is essentially what you'd be doing if you cut your beam in half, however, they add another control arm to the mix.
RacerFreakXXXThread starterSomers NY · Sep 13, 2009#45
Originally Posted by lilredrocket ↑
Racer. You said you were thinking about getting coils. Do you want them for adjusting the Dampning of the shocks if so them look the the Tokico HTS shocks and struts more than the standard pair but worth it too!!
do they even make those shocks for the car? I actually wanted only about .5-1" clearance and wanted to be able to adjust the dampening. I'm going to get the tokico blue's and see how I feel about the car with them on.
lilredrocketDFW, Texas · Sep 13, 2009#46
Don't get the blues then the HTSs (reds) ask Garm I believe he can get the reds they are a little over double the cost of blues I think. Kngrsll has the reds on his car
RacerFreakXXXThread starterSomers NY · Sep 13, 2009#47
rofl... a little over double the cost is about $700 and for tripple I can get BC coilovers. My original intention was to get coilovers but I got springs for temp cuz they are cheap but I'd rather get blue's and get coilovers later than pay that much for struts.
detroiterMetro Detroit · Sep 13, 2009#48
After you get the blues and throw all your goodies on, you might just end up keeping that setup. Never know!
RacerFreakXXXThread starterSomers NY · Sep 14, 2009#49
exactly... I'm gonna get 5zigen fn01r-c 16x7 +33 with 10mm penguin spacers on the rear :D soI'll see how the setup looks with the drop.
kngrsllSpartanburg, SC · Sep 14, 2009#50
i love my shocks and springs, i wouldnt trade them for any coilover i have seen yet. i cant wait to try out some of the stiffer rear Fit springs. it handles really well with the stock rear fit springs on it now.