Yarisworld Archive

So...I cracked a weld...

18 posts · 4,416 views

SabretoothOriginal postSt Cloud FL · Aug 27, 2009#1
Its official, I might be the first confirmed case of a Megan Exhaust taking a crap on their owner...lol

I noticed earlier this week that my car was louder, I figured prolly something was loose or I had a leak somewhere... I checked the gasket where the axleback is, its tight and even.

Then I decided to go ahead and check to see if I had a crack in the muffler, piping, whatever...nope, not that either. So then I decided to check the welds around the "flange" where the axleback meets to the midpipe, yep...there it was, inside weld has a small crack in it.

Best part about it all, I never hit ANYTHING within the last week, month, or even a year that would cause the damage to the exhaust...lol

Only plus side to this is, my car sounds a bit meaner, It "putts" a bit now while engine braking. Completely noticeable change in the sound and loudness of the exhaust.


New Header/Exhaust setup coming soon! Contemplating a straight pipe, 2.25'', double res, center tip exhaust.



I dont mean to turn this into a debate thread, but it more than likely will become that. Just sharing my story and learnings along the way to building a better car.

Replies 17

CASTREXCosta Rica · Aug 27, 2009#2
I cracked the tranny mount and one of the shifter cables on my Yaris... And it's only 20K miles.

Toyota sucks...

🤷
lilredrocketDFW, Texas · Aug 27, 2009#3
I think JT258 cracked his Megan header but he didn't put the spring for the bolts thats why his cracked
HerbicidalRoseville, CA - USA. · Aug 27, 2009#4
Hmmmm. I just installed a Megan header on my Yaris but I was not able to reuse the Toyota factory bolts (with the spring around them) when connecting the Megan header to the mid-pipe. My Toyota mechanic buddy says that connection is designed to flex, that's why the bolts have the springs. I could not reuse them on the Megan header because they do not match the factory thread pitch. In my opinion, that was a big engineering boo boo on Megan's part. 👎 They should have used the same pitch of thread so we could reuse factory bolts. Now that is a rigid connection, when it should be a flexible one. I've kept my spring bolts and I may pull the header and drill out Megans thread and helicoil the correct threads in place.

I'm currently dealing with an air/fuel sensor issue so I don't have any seat time with the Megan header yet.
SabretoothThread starterSt Cloud FL · Aug 27, 2009#5
Ya...i am kinda glad I sold my Megan Header...

I will be looking into a DC one soon enough
ddongbaphay · Aug 27, 2009#6
Call Megan. They're really good about customer service. They might send you a weld in the mail or something.
lilredrocketDFW, Texas · Aug 27, 2009#7
Herbicidal don't drill out the header just go to a parts store and get the right thred pitch bolts then reuse the springs with the new bolts
PHXDEMONPhoenix, AZ · Aug 27, 2009#8
Originally Posted by ddongbap ↑
Call Megan. They're really good about customer service. They might send you a weld in the mail or something.
Sending welds in the mail WTF 😆😆😆 Megan is just glorified ebay IMO. I'm not suprised this happened.
supmetSouthern California · Aug 27, 2009#9
Originally Posted by Sabretooth ↑
Best part about it all, I never hit ANYTHING within the last week, month, or even a year that would cause the damage to the exhaust...lol
I must be retarded for scraping my stock exhaust with stock springs 🤷

Props for being the worlds most careful driver.
SabretoothThread starterSt Cloud FL · Aug 27, 2009#10
^^^
I try, lmao!
HerbicidalRoseville, CA - USA. · Aug 27, 2009#11
Originally Posted by lilredrocket ↑
Herbicidal don't drill out the header just go to a parts store and get the right thred pitch bolts then reuse the springs with the new bolts
Thanks for the suggestion. 👍 Although it may take some looking to find the right bolt that will accommodate the spring, etc.
SabretoothThread starterSt Cloud FL · Aug 27, 2009#12
nope...a large thick washer works fine on a smaller bolt when trying to compress a spring...just need something to guide the spring to keep it somewhat center. Ghetto-fab sometimes works.
jt258HOUSTON · Sep 2, 2009#13
AND THATS WHY I GLAD I SWITCHED TO DC SPORTS NEVER HAD A PROBLEM SINCE.
SabretoothThread starterSt Cloud FL · Sep 2, 2009#14
Well...the thread is about the Megan Exhaust Axleback exhaust, not their header.
kngrsllSpartanburg, SC · Sep 2, 2009#15
i was afraid that this thread was going to be about chassis welds, thank god it isnt.

a cracked weld is not what you want at 95 mph in a right hand kink lol
SabretoothThread starterSt Cloud FL · Sep 2, 2009#16
Your dragon days would be numbered if thats the case...😆
kngrsllSpartanburg, SC · Sep 2, 2009#17
Originally Posted by Sabretooth ↑
Your dragon days would be numbered if thats the case...😆
The S2000 has problems with the chassis welds cracking in the front 😲
YarisPRMayaWest, Puerto Rico · Sep 2, 2009#18
Originally Posted by CASTREX ↑
I cracked the tranny mount and one of the shifter cables on my Yaris... And it's only 20K miles.

Toyota sucks...

🤷
...same her mine broke @ 22K. I have a looong list of things gone wrong with my car but i ahve to thank God for the warranty I have used it a lot