Goku87, so far I don't have any solid info. I am looking into purchasing a Chinese clone of the techstream VIM for $1500. I believe, based on Mike's dealer's response, that it can be done using techstream.
TACH-cluster replacement-resetting ODO?
92 posts · 56,363 views · page 2 of 2
Replies continued
jebus that is a lot of $$$
It is indeed, but it is a whole lot less than $7,500 for the real Toyota one. My interest in it is to "sniff" its communication when doing various things to the ECM or other ECU's. This would allow me to build inexpensive modules to allow others to do those same tasks. It also has the ability to flash the ECM. Sniffing that process is the key to cracking the ECM.
does anyone have a 08 yaris lb automatic trans ecu with 35000 miles or less on the car when it was pulled im looking for one to buy ?
Has anyone tried this yet? I just read through it all and didn't see anyone saying this didn't work.Originally Posted by CTScott ↑As a side note, a while back nickhjort sent me some pics from when we were trying to figure out if we could get the 07-08 clusters to drive cruise control lights.
Looking back though the pics recently I realized that the cluster has a "core" module with the microcontroller on it, which is plugged into a "carrier" board (i.e. the big circuit board with the lights and speedo). The mileage on the cluster end is stored in flash memory within this microcontroller. If the cold boot via battery disconnect doesn't work, It may be possible to move the core over from the old to new cluster. The question is if the microcontroller is programmed generically and it drives whatever is available on the carrier it is plugged into, or if it is programmed specifically for the carrier.
Attachment 27136
ive been scouring junk yards here, back home, and on the internet-a-plenty.
i'm almost tempted to say screw it and get the one from the stealership.
its only $460.00ish....
only....... 🙁
i'm almost tempted to say screw it and get the one from the stealership.
its only $460.00ish....
only....... 🙁
Someone from Puerto Rico did, and it did not work for him - The new cluster had a blank display for mileage with the old cluster's core. It may be that you can only swap out ones from the same vintage, or it may be that it just doesn't work.Originally Posted by jdms ↑Has anyone tried this yet? I just read through it all and didn't see anyone saying this didn't work.
It's also possible they didn't install it correctly, or one of the 50 or so pins were bent, etc. that's a pretty fragile piece. I think that idea makes a lot of sense though.
I just want a clear answer... will a cluster with a Tach work in a Yaris that did not come with a Tach >.> millage doesn't really concern me.
yes it will, at a meet last week, we had a 09 S automatic cluster swapped into a pre 09 no tach (manual), worked, we dont know about ODO tho.
looking back on this i guess i'm glad i never got the new cluster lol.
I just bought a cluster from ebay and waiting for arrival. For me, I am after with the tach.
Is the odometer reading stays with the ecm or it follows the cluster ecu?🆘
Is the odometer reading stays with the ecm or it follows the cluster ecu?🆘
It stays with the cluster ECU. The ECM doesn't store odo data.Originally Posted by du2efs ↑I just bought a cluster from ebay and waiting for arrival. For me, I am after with the tach.
Is the odometer reading stays with the ecm or it follows the cluster ecu?🆘
Thanks CTScott:Originally Posted by CTScott ↑It stays with the cluster ECU. The ECM doesn't store odo data.
83800-52F80 ----> 83800-52F30 ..fingers cross👍
83800-52F30 is Canada/Mexico 06-07 for non-ABS, so it will work on yours and will be in KM.
I think it has the ABS..this is the description i got from toyodiy.comOriginally Posted by CTScott ↑83800-52F30 is Canada/Mexico 06-07 for non-ABS, so it will work on yours and will be in KM.
83800-52F30 NCP93..MTM..CND; WITH 15 INCH DISC WHEEL & CRUISE CONTROL & ABS(ANTI-LOCK BRK SYSTM)-WITH(WITHOUT BRAKE ASSIST)
My new sedan instrument cluster 83800-52F30

My old instrument cluster 83800-52F80

Many thanks to ebay seller LKQ

My old instrument cluster 83800-52F80

Many thanks to ebay seller LKQ
du2efs... If you use a flash light on the cluster, can you see the outline of the "Cruise" control logo on the cluster??.. It should be near the top right side of the speedo..
Originally Posted by du2efs ↑My new sedan instrument cluster 83800-52F30
My old instrument cluster 83800-52F80
Many thanks to ebay seller LKQ
the cluster p/n 83800-52F30 I got has no cruise control led or indicator. I have checked the PCB, no resistor and smt led. :(
I noticed that the Illumination(dial and pointer) is not working after the swap. Everything else is working except the dial pointer illumination.
I have compared the cluster ecu board part by part and its same.Probably the programming is different as i tried to swap the ecu board with the tach and non-tach, the dial and ponter lights works but the tach and speedo is not working. 😠
Last resort is to jumper the clock backlight to the pointer and dial.
I have compared the cluster ecu board part by part and its same.Probably the programming is different as i tried to swap the ecu board with the tach and non-tach, the dial and ponter lights works but the tach and speedo is not working. 😠
Last resort is to jumper the clock backlight to the pointer and dial.
Before you swapped the ECU was it just the Tach dial and pointer not illuminating, or both the Speedo and Tach dials/pointers?
after the swap, the gauge backlight, pointers(tach+speedo) is not working..Rest of the functions is working.Originally Posted by darkMINI ↑Before you swapped the ECU was it just the Tach dial and pointer not illuminating, or both the Speedo and Tach dials/pointers?
Below my observation:
My wiring harness is not the same. The canadian cluster has the illumination control and GCC/EU model don't have. To fix this, You have to swap/jumper or rig the illumination pinout of the new cluster.
I put it back my original cluster as I am annoyed without the illumination/backlight. Everything works fine. From here, I noticed also that they have different programming cluster daughter board. Tried to swap their daughter boards also but the results is more bad(none of the pointers is working).
So, I've been searching all these Tach Cluster threads and still have not been able to verify if I can put a tach cluster in my '08 3dr HB MT US base model. If it is possible does anyone have an idea of which clusters will work without issue?
I was thinking of trying a cluster from an '08 US HB auto trans model.
We need to make a chart showing what will work with what.
I was thinking of trying a cluster from an '08 US HB auto trans model.
We need to make a chart showing what will work with what.
For USDM ones, the key is getting one with ABS if your car has it and without if it doesn't. In some cases the opposite will still work, but you are always safe if you match for ABS.Originally Posted by darkMINI ↑So, I've been searching all these Tach Cluster threads and still have not been able to verify if I can put a tach cluster in my '08 3dr HB MT US base model. If it is possible does anyone have an idea of which clusters will work without issue?
I was thinking of trying a cluster from an '08 US HB auto trans model.
We need to make a chart showing what will work with what.
Right on Scott, that narrows the search a bit.
Love your snowplow BTW
Love your snowplow BTW
Thread revival time!
I've been plowing though as many threads as I can, but I still can't find the part number for a USDM cluster w/tach and ABS. I've found some part numbers on villagetoyotaparts.com and toyoDIY, but the descriptions are either absent, or not helpful.
Here's what I've found so far at villagetoyotaparts.com for a 2010 USDM 3DR MT:
83800-52L30 - speedo only (2010 hatch, ebay listing)
83800-52L40 - ???
83800-52N61 - speedo only (2009 hatch, ebay listing)
83800-52N71 - w/tach and ABS
83800-52P01 - ???
83800-52X00 - ???
Could someone with a USDM hatch with tach pull their cluster and verify the part number?
*edit*
Ok, after more poking around at toyotapartszone.com, I found about a dozen part numbers for the 09 North American hatch. Sadly, they either say "Mexico spec" or "not available". The descriptions seem to be a bit better, but having a description for a part that doesn't exist anymore is pretty useless. =/
I've been plowing though as many threads as I can, but I still can't find the part number for a USDM cluster w/tach and ABS. I've found some part numbers on villagetoyotaparts.com and toyoDIY, but the descriptions are either absent, or not helpful.
Here's what I've found so far at villagetoyotaparts.com for a 2010 USDM 3DR MT:
83800-52L30 - speedo only (2010 hatch, ebay listing)
83800-52L40 - ???
83800-52N61 - speedo only (2009 hatch, ebay listing)
83800-52N71 - w/tach and ABS
83800-52P01 - ???
83800-52X00 - ???
Could someone with a USDM hatch with tach pull their cluster and verify the part number?
*edit*
Ok, after more poking around at toyotapartszone.com, I found about a dozen part numbers for the 09 North American hatch. Sadly, they either say "Mexico spec" or "not available". The descriptions seem to be a bit better, but having a description for a part that doesn't exist anymore is pretty useless. =/
Originally Posted by CrankyOldMan ↑Thread revival time!
I've been plowing though as many threads as I can, but I still can't find the part number for a USDM cluster w/tach and ABS. I've found some part numbers on villagetoyotaparts.com and toyoDIY, but the descriptions are either absent, or not helpful.
Here's what I've found so far at villagetoyotaparts.com for a 2010 USDM 3DR MT:
83800-52L30 - speedo only (2010 hatch, ebay listing)
83800-52L40 - ???
83800-52N61 - speedo only (2009 hatch, ebay listing)
83800-52N71 - ???
83800-52P01 - ???
83800-52X00 - ???
Could someone with a USDM hatch with tach pull their cluster and verify the part number?
*edit*
Ok, after more poking around at toyotapartszone.com, I found about a dozen part numbers for the 09 North American hatch. Sadly, they either say "Mexico spec" or "not available". The descriptions seem to be a bit better, but having a description for a part that doesn't exist anymore is pretty useless. =/
For an 09+ with ABS and the Tach: 83800-52N71
I know this Thread is almost 4yrs old... Don't Shoot Me!
On the 09+ LB w/abs WITH TACH, does it matter?, or which Part # is correct for 5-Speed and which for AT?
On the 09+ LB w/abs WITH TACH, does it matter?, or which Part # is correct for 5-Speed and which for AT?
I got 07 hatch none tach and I found one for $150 09 hatch with tach. Can anyone provide me some information here please. Can i just swap it over and plug and play or I need to change wht hardness. Thx!!!
09 S Cluster needs to be matched with car with abs or the mph needle wont move.
S cluster doesnt matter Auto or Manual.
Harness is the same, its simple plug and play.
S cluster doesnt matter Auto or Manual.
Harness is the same, its simple plug and play.
Thanks for reply. So all 09 cluster comes with abs. Can i get one with out abs and then both will be working fine. thx!Originally Posted by ezhacker1 ↑09 S Cluster needs to be matched with car with abs or the mph needle wont move.
S cluster doesnt matter Auto or Manual.
Harness is the same, its simple plug and play.
With US ones ALL come WITH ABS. The speedometer issue is only when using a JDM cluster on a non ABS US car. If you use a U.S. ABS one on a non ABS car the ABS and brake lights will always be on. You can disable those lights to make it usable.
Thank you very much! CTScottOriginally Posted by CTScott ↑With US ones ALL come WITH ABS. The speedometer issue is only when using a JDM cluster on a non ABS US car. If you use a U.S. ABS one on a non ABS car the ABS and brake lights will always be on. You can disable those lights to make it usable.
I read this whole thread, is there an end all answer for this?
I'm reading "discon the battery first and it'll work" then "that doesn't work" then "the dealer can do it" then "the dealer can't do it"
What's the actual answer here??
I'd sure love to have a tach, on the cluster on my 08 manual...
I'm reading "discon the battery first and it'll work" then "that doesn't work" then "the dealer can do it" then "the dealer can't do it"
What's the actual answer here??
I'd sure love to have a tach, on the cluster on my 08 manual...
The final and definite answer is it can only be done by someone with specialized equipment to reflash the EEPROM on the module. It can't be done by disconnecting the battery and it can't be done by the dealer. I have the equipment and offer the service, if you track one down.Originally Posted by MJZ ↑I read this whole thread, is there an end all answer for this?
I'm reading "discon the battery first and it'll work" then "that doesn't work" then "the dealer can do it" then "the dealer can't do it"
What's the actual answer here??
I'd sure love to have a tach, on the cluster on my 08 manual...
Good to know!Originally Posted by CTScott ↑The final and definite answer is it can only be done by someone with specialized equipment to reflash the EEPROM on the module. It can't be done by disconnecting the battery and it can't be done by the dealer. I have the equipment and offer the service, if you track one down.
CT, I'm thinking about doing the swap to the type S to get the tach. If I did this what would flashing the mileage include? I.e. do I need to send it to you with my old cluster or something and how much would you want?
You would just have to send me the new one (and shoot me a pic of your current one with its current mileage). I charge $40 + return shipping to reprogram them.Originally Posted by scoobopdan ↑CT, I'm thinking about doing the swap to the type S to get the tach. If I did this what would flashing the mileage include? I.e. do I need to send it to you with my old cluster or something and how much would you want?
Good to know CT, I'm in the middle of moving so it may take a month or two but i'll definitely be PMing you in the future, thanks!
Hello,
Could anyone help me with an instrument cluster pinout for a 2003 EU Yaris TS?
I have attached some pictures with the plugs.
There are 2 connectors (22 and 18 pins), and one 6 pins smaller connector that goes with the buttons.
Thank you!








Could anyone help me with an instrument cluster pinout for a 2003 EU Yaris TS?
I have attached some pictures with the plugs.
There are 2 connectors (22 and 18 pins), and one 6 pins smaller connector that goes with the buttons.
Thank you!









Forgot to mention: it's MkII (facelift) version (in the reg book, it's written 2004). But the parts are marked with 2003 :)
Solved it. I'll post some walkthrough and pictures later.
Basically it's very similar to Funcargo pinout.
Basically it's very similar to Funcargo pinout.