Yarisworld Archive

Changing to LED-bulbs

22 posts · 11,305 views

JochenOriginal postGullegem - Belgium · Aug 3, 2009#1
I've changed every interior bulb to LED-bulbs so I got that nice white (a little blue) look.

Picture not included in this copy

The difference between LED-bulbs (in front) and original bulbs (middle)
Picture not included in this copy

This one is a little more blueish than the lights in front.
Picture not included in this copy

Before and after:
Picture not included in this copy

Even changed the one in the trunk
Picture not included in this copy

Picture not included in this copy

And finally, the license plate
Picture not included in this copy

Replies 21

CtrlAltDefeatIndianapolis IN · Aug 3, 2009#2
nice! I hope to do that too some day, but I'm working on strictly performance right now...
Sparks Toyota-TRDMyrtle Beach, SC · Aug 3, 2009#3
That looks good!


Tim
JumpmanYarisSO. INDIANA · Aug 3, 2009#4
I changed them as well they seem to be less bright then the stock ones but i still like them
NorkotikEl Monte CA · Aug 4, 2009#5
PRETTY TIGHT
kacWest/Central Illinois · Aug 4, 2009#6
very nice results. What LEDs did you buy? Where did you get 'em? How much did they cost? Was it an easy change?
enobmort42Denver, CO · Aug 4, 2009#7
i just placed my order a little while ago through autolumination.com to do my parking, brake, reverse, turns, side markers, dome/map/trunk, and license plate all in LED.. it cost me about $85-90 i think?
IsLNdbOiLas Vegas, NV · Aug 5, 2009#8
I've changed all of my interior lights too. Got mine from VLEDs. Still waiting for someone to try using a white, 4" CFL in place of the rear license plate light.
JochenThread starterGullegem - Belgium · Aug 5, 2009#9
It's pretty easy, but here's a small DIY.

I used T10 bulbs like this for the map lights and license plate (about 6$ for 2):
Picture not included in this copy

A bulb like this for the dome light (31mm) and the trunk (37mm). Note that these are 2 different sizes. (about 10$ each)
Picture not included in this copy


Picture not included in this copy
Use a screwdriver at those 4 points, just pull the lights out (no turning or pushing, just pulling)

Picture not included in this copy
Use a screwdriver at those 2 points

Picture not included in this copy
Use a screwdriver at this side, plug it out by pushing the clip at the connector, change the bulb, plug it in

And that's how easy it is.

The license plate was a bit trickier. There's 2 clips at the sides you have to pull inwards and then pull it down. It doesn't come out that easy.
Then just turn the socket en pull it out, change bulb and put everything back.
kacWest/Central Illinois · Aug 5, 2009#10
Nice little DIY, this is something I would like to do in the near future.
rock On!
mario.guzmanCalifornia · Aug 22, 2009#11
I just wanted to know where you bought those LED lights and if they are simple to install. I have an '08 Yaris Sedan that I'd like to do that too. My main focus right now is to change the back lights that shine on the License Plate itself to be LED.

So, again, I'd like to know where I can buy them, if they are easy to install and if I need to buy anything else. I'm assuming it's just the bulb you change for everything? Also, around what range of price should I be looking in? Thanks!!!

Mario G.
Riverside, CA
ethelitershouston · Aug 23, 2009#12
great write up. autoillumination...
47_MasoN_47Northwest Alabama · Aug 24, 2009#13
I was going to do the same thing. The first ones I bought are some for the license plate, but I'm having a hard time getting to the bulbs to replace them :( I'll look for those 2 clips you talk about and see if I can get it.
JochenThread starterGullegem - Belgium · Aug 24, 2009#14
Picture not included in this copy

Don't use screwdrivers but small pliers, so you can hold the clips and pull it. You have to wiggle the whole thing a bit. Pull a bit on the left, a bit on the right, ...
I also had to remove my license plate because I couldn't pull the whole thing down.

Oh, and a small tip: Test the light before you put everything back in 😉


ps. Sorry for the cellphone pic, our camera is broken.
RedRideMiddletown, NY · Aug 24, 2009#15
Very useful DIY. 👍
Personally, I just (today) installed some "Polarg M4 B1 hyird" hyper white bulbs in my map lights.
I just happend to have them on hand (I use them in my other car) and I already installed them in my front parking and license plate lights.

However, I just ordered a led bulb for the dome light. The DIY informed me what size (31mm) to get. 🙂
47_MasoN_47Northwest Alabama · Aug 25, 2009#16
Hmm I'm guessing you have the liftback? I don't see those clips anywhere on the sedan :(
JochenThread starterGullegem - Belgium · Aug 25, 2009#18
Originally Posted by 47_MasoN_47 ↑
Hmm I'm guessing you have the liftback? I don't see those clips anywhere on the sedan :(
Yes, it's a hatchback.
47_MasoN_47Northwest Alabama · Aug 25, 2009#19
I figured it out for the sedan.

Open the trunk and remove the 2 rubber plug things that hold the cloth cover to the inside of the trunk lid. Pull down on that slightly so that you can see the 2 wires that go to the bulbs for the lag lights. Twist, but not too hard, and it should move about 1/4" or so. If it seems to be taking a lot of force twist it the other way. Once it moves the 1/4" or so it should just fall free, then you can disconnect the bulb housing deal from the wire and pull the bulb from the housing. It took considerable force to get the bulbs out for mine. Then you can put the new bulbs in and you are good to go! I'll take pictures of mine tonight when it gets dark :)
husaynkhanmauritius · Apr 17, 2010#20
hi. if you can explained me how to remove the dome lights?
Yaris4everAustralia · Apr 17, 2010#21
Great thread, thanks for the info & those led bulbs really make a big difference!!!!!
JochenThread starterGullegem - Belgium · Apr 18, 2010#22
Originally Posted by husaynkhan ↑
hi. if you can explained me how to remove the dome lights?
Hi, I explained everything in post #9: Changing to LED-bulbs