ChinoCharlesOriginal postOH · Jul 29, 2009#1Picture not included in this copy
Discuss. 😆 Nexus, Tamago, Garm, etc... if you'd like to bring some of our private conversations into this thread to add to the knowledgebase of the community, feel free. I'll post some of what I took away from it when I'm not at work. I'll just say that I'm excited at what this thing will do when the tune is right! Looks like that 180 WHP might be in this thing after all.
Sorry for the crap picture. They're supposed to e-mail me the actual graph eventually. Also, no AFR! I need me a wideband, like, yesterday.
Replies 35
TamagoOff Grid · Jul 29, 2009#2you need to pull fuel out in that valley.
honestly the graph is useless without an AFR chart :( sorry dude.
i'd imagine you're pulling too much timing with the Blue too.
time to buy a wideband! *cough cough*
ChinoCharlesThread starterOH · Jul 29, 2009#3No, you're right and I know that. I guess question one is, well, a multi-part question. LOL
[1] Is the e-manage blue strong enough to continue under the assumption that this is what I'll be using to tune it OR do I need to start thinking standalone?
[2] What widebands would work well?
[3] What is this Nexus keeps talking about regarding a narrowband sim and why is that so important?
TamagoOff Grid · Jul 29, 2009#41. the emanage has potential to do the job, because you're only running 10 psi. you're well within the parameters available in the emanage at this point.
2. any wideband will work, most are 5 wire "bosch" setups. my Innovate G2 (LC1+ gauge) actually comes with a wideband controller that will simulate your stock o2 sensor if need be, and has narrowband and wideband outputs built in, as well as some datalogging. great unit (IMO better than the AEM unit)
3. narrowband SIM is used to basically trick the stock ECU into seeing "stoich" even when it's not. so you can add fuel without the stock ECU fighting the Greddy unit.
ChinoCharlesThread starterOH · Jul 29, 2009#5OK, so step one is probably:
[1] Get and install a wideband
[2] Get a cable for the e-manage, the software and a laptop
[3] Go to the track and datalog a run
Does that seem reasonable?
TamagoOff Grid · Jul 29, 2009#6don't need to do track to datalog. i recommend street tuning, since the car is primarily driven on the street. make it easy to drive, and the power will come second (but still improve over your current numbers.. unless there's something wrong with your snail)
ChinoCharlesThread starterOH · Jul 29, 2009#7Well the good news is that the impeller spins freely and there is no shaft play. We just checked it last weekend.
Street tuning it is.
cali yarisCanoga Park, CA · Jul 29, 2009#8agreed that without an a/f curve, you can't do much with that dyno chart. Further, a boost curve would be really useful too. If you're making full boost (10psi) but not power and the equipment is sound, you need fuel and timing adjustments to bring that number up.
something odd though - our rev limiter is 6250, but your dyno goes past that. What's up with that? Tamago?
ChinoCharlesThread starterOH · Jul 29, 2009#9I just posted it to show that it needs help, basically. We can still figure out what needs to be done. The apparent answer is I need some AFR readings pronto, which I already knew but I like having you guys chime in every step of the way. I trust y'all. Why this is happening (power flatline) will come with time and a little effort.
TamagoOff Grid · Jul 29, 2009#10 Originally Posted by
cali yaris ↑ something odd though - our rev limiter is 6250, but your dyno goes past that. What's up with that? Tamago?
are you sure that's not 6520? 62 is really low.
mikenacaratoBrentwood, TN · Jul 29, 2009#11my car hits 6500 then bounces
CASTREXCosta Rica · Jul 29, 2009#12^^
Yeap, the redline is at 6,400rpm and the limiter will kick in very shortly after it. So 6,500 sounds about right...
cali yarisCanoga Park, CA · Jul 29, 2009#136250 is our rev limiter, most of the dynos show peak power at about 5800, including mine both stock and turbo'd.
yeah i see mine over-revving too.
CASTREXCosta Rica · Jul 29, 2009#14 Originally Posted by
Tamago ↑ 3. narrowband SIM is used to basically trick the stock ECU into seeing "stoich" even when it's not. so you can add fuel without the stock ECU fighting the Greddy unit.
So basically could allow us to remove the OE O2 sensor and have it replaced it with a wideband and feed the ECU with the simulated signal?
Would this have the same "effect" of a MAF clamp?
Doesn't our cars have some sort of hybrid O2 sensor? I read somewere that although the OE sensor is not a wideband it is somewhat more advance than a regular narrow band sensor...
Just some thoughts.
ChinoCharlesThread starterOH · Jul 29, 2009#15Keep the thoughts coming. I'll be referencing this thread often in the coming weeks and I need the info.
TamagoOff Grid · Jul 29, 2009#16 Originally Posted by
cali yaris ↑ 6250 is our rev limiter, most of the dynos show peak power at about 5800, including mine both stock and turbo'd.
yeah i see mine over-revving too.
where are you getting this 6250 number?
cali yarisCanoga Park, CA · Jul 29, 2009#17My car. If you rev up your motor slowly, that's where the rev limiter engages -- at least on my car it does. Anyone else test in that way?
TamagoOff Grid · Jul 29, 2009#18 Originally Posted by
cali yaris ↑ My car. If you rev up your motor slowly, that's where the rev limiter engages -- at least on my car it does. Anyone else test in that way?
your car has stand-alone engine management.
ChinoCharlesThread starterOH · Jul 29, 2009#19Mine definitely revs above 6,250. 6,500 is limit.
Nexus1155Dorchester · Jul 29, 2009#20OK you punk, so heres the deal, i got the cable and a pressure sensor to send you in the mail so you will be on your way, hopefully that wideband can sim a narrowband signal. then we can get rid of your CEL and get to logging and tuning the car how it should be tuned. and that little dropoff that your prob sensing, i dont remember where you said is prob where the system sees boost and is like HOLY S why is there pressure like that
ChinoCharlesThread starterOH · Jul 29, 2009#21LOL. Plan is to buy Tamago's wideband next week. Onwards!
Penguin GarageFL · Jul 30, 2009#22sucks they didn't plug in a tail pipe sniffer to get you some A/F readings. :(
peak increase looks good though, over 40hp over stock is a nice bump. :)
Will be following, once a viable tuning solution and some of the bugs are figured out we may go boosted. :)
Nexus1155Dorchester · Jul 30, 2009#23Chino i actually got a 2.5BAR MAP Sensor for you right here from an Audi with harness. Should be good for about 22psi like youll ever see that much!!! :P :P Very Simple, just find some place to plug it on the intake, comes with 3 Wires, should just be Signal, 5v, ground right into the connector and you should be good to go, or hopefully lol
So with the jankyness were rigging up, with the wideband, MAP Sensor, and injector harness, and soon ignition harness you should be running at the peak of your peeformance
cali yarisCanoga Park, CA · Jul 30, 2009#24 your car has stand-alone engine management.
duh. which is currently set to 7000. I meant before that, sorry if I wasn't clear that we were talking about the rev limiter in the stock Yaris ECU.
ChinoCharlesThread starterOH · Jul 30, 2009#25 Originally Posted by
Nexus1155 ↑ Chino i actually got a 2.5BAR MAP Sensor for you right here from an Audi with harness. Should be good for about 22psi like youll ever see that much!!! :P :P Very Simple, just find some place to plug it on the intake, comes with 3 Wires, should just be Signal, 5v, ground right into the connector and you should be good to go, or hopefully lol
So with the jankyness were rigging up, with the wideband, MAP Sensor, and injector harness, and soon ignition harness you should be running at the peak of your peeformance
You are the man!
ChinoCharlesThread starterOH · Aug 5, 2009#26Map sensor: CHECK
Picture not included in this copy Audi boost sensor... to be the fourth manufacturer's part to be installed on this car. 😆 Thanks Nexus!
1 attachment not included in this copy
ChinoCharlesThread starterOH · Aug 5, 2009#27Oh, update: Big 3 Racing in Medina, Ohio agreed to run the car on the dyno with a wideband and scan the codes and give me a proper reading and all that fun crap. I'm trying to get in there this weekend.
cali yarisCanoga Park, CA · Aug 5, 2009#28 to be the fourth manufacturer's part to be installed on this car.
I bet you have more than four. 😉 I've never counted, probably shouldn't. LOL
ChinoCharlesThread starterOH · Aug 5, 2009#29CAR manufacturer. LOL. Toyota, Mitsubishi, BMW, Audi... what am I missing?
Nexus1155Dorchester · Aug 6, 2009#30LOL what do you have from a BMW?! But yeah no problem, hopefully the cable works out well for you too, but i still need to find out what kind of pressure sensor that is. I know it sends 0-5v which is fine, just need to see what it reads to... I'm almost positive its 2.5bar
cali yarisCanoga Park, CA · Aug 6, 2009#31 to be the fourth manufacturer's part to be installed on this car.
Apparently, I was missing the word CAR. LOL
But an overall brand list WOULD be kind of fun. 😉
ChinoCharlesThread starterOH · Aug 6, 2009#32UPDATE: Just got off the phone with Monkey Wrench Racing in Michigan. They tuned a local 2ZZ with an e-manage blue and I was referred by him, and after reading up on their projects I think I'm going to Michigan. If anyone is going to figure it out, they will. They're the guys you go to to make serious power in your Lotus. Might need an E-manage ultimate, but I'm going to leave that to the experts. The tuner is @ Bonneville for the next week or so so I won't know for sure until later this month.
CASTREXCosta Rica · Aug 6, 2009#33Good Call.
MWR are the guys to ask when it comes down to the 1ZZ and the 2ZZ engines. Close enough to our little 1NZ.
BTW, did I mention that I received a confirmation from Boomslang and they will be coming out a PnP FIC harness for the yaris in the next few weeks?
off topic, but this should be goos news for the people looking into FI.
ChinoCharlesThread starterOH · Aug 17, 2009#34UPDATE: Just talked to MWR and we're slated to tune my car in two months, mid October sometime. That will give me enough time to tie some things up on this end. The wait begins.
cali yarisCanoga Park, CA · Aug 17, 2009#35awesome!! meet ya at IA next year?
ChinoCharlesThread starterOH · Aug 17, 2009#36It is on my friend!