In your Youtube links its says under 'more info' you are running under drive pulley/s...so not anymore? or is it a c-one brand?
My 2007 Yaris S doing 350,000 miles in less than 3yrs.
73 posts · 26,114 views · page 2 of 2
Replies continued
I've had a few cars get into the 200k mileage, so I'm glad you write about the obvious need for maintenance, b/c I don't think the OP is doing proper maintenance (brakes, balljoints, etc.), especially when safety is a factor. I also mentioned the valves earlier, but I don't think I went into detail as you did here. i'm not sure what else the tapping could be, as valves go at this point in time.Originally Posted by bronsin ↑The source of your pinging is carbon deposits on the cylinder head/pistons. You might consider having the head removed and decarbonized. Also ask them to check your valves and guides for replacement. (valve job) You really want to consider replacing the valves at this point because its POSSIBLE the head of one of them (probably an exhaust valve) could break off and smash up the engine. Your mileage decrease is probably due to valve sealing issues. I also have to believe your timing chain should be checked/replaced too. If it breaks it will destroy the engine. BTW have you had the ball joints/tie rods/steering rack checked? Any failure here and you crash/die. Good luck with it!
@ trini: but still, 350k is amazing, are you the google maps guy? lol
I knock on wood for you!
That pinging might be the beginnings of some rod-wear. My Geo started doing that about 80k miles ago. Still runs great, but I couldn't trust it anymore for long distance travel due to the noise and slight power loss. When a few mechanics confirmed my suspicion, I bought my Yaris. The Geo has 230k miles. 350+K miles sounds good--if my back holds out. Trying to reach the steering wheel is slowly destroying it.
Originally Posted by wornways ↑That pinging might be the beginnings of some rod-wear. My Geo started doing that about 80k miles ago. Still runs great, but I couldn't trust it anymore for long distance travel due to the noise and slight power loss. When a few mechanics confirmed my suspicion, I bought my Yaris. The Geo has 230k miles. 350+K miles sounds good--if my back holds out. Trying to reach the steering wheel is slowly destroying it.
Rod bearings with play in them do not hang around for 80,000 miles, they quickly self destruct. Probably all you needed was a valve job. Although after 230k miles a new car would be a lot more dependable...
I have a dynomax exhaust, but cruising at 70mph, you don't hear any intake or exhaust noise. The car is almost as quiet as factory while cruising.Originally Posted by Split ↑do you have an exhaust system as well? I'm baffled that you'd drive so much with an intake and header, doesn't the noise get to you after a while? I suppose if you have the factory muffler on you're probably okay.
I had an NST pulley, but I sold it.Originally Posted by Kioshi ↑In your Youtube links its says under 'more info' you are running under drive pulley/s...so not anymore? or is it a c-one brand?
the mechanical head/valves is the achilles heal of this engine, it is a very involved jon to adjust them, at 350K they definately need adjustment. But It would be cheaper to drive till a valve drops and replace with a low milage JY pull.
Yes its probably asking a lot for a Toyota mechanic to adjust these valves. No other Toyota uses this system. And there are very few ECHOs/Yaris's sold compared to other Toyotas. You might be better off taking the car to a motorcycle mechanic because this system is common on motorcycle engines. Although....it IS relatively easy to CHECK the valve clearances for the home mechanic. Its adjusting them thats involved.
I got a Yaris (2007) which is 18 months old and 81K with no problems yet! Also have a 2005 Ford Ranger with 378K. Started to ping sometime back and I was using high test so I wouldn't have to listen to the marbles in the engine. Finally had Ford look at it and they stated that the time chain had streched. I told them it wasn't worth it to replace the chain so they reset the timing to a place where the pinging stopped. Don't know whether it was advanced or retarded. Now I'm back to low test fuel and I really don't feel a major difference. So add the chain to all the possible pinging issues.
JEM
JEM
How much mileage did you put on the NST pulley before you sold it and why sold it? cause NST pulley's will be my next mod. 😕Originally Posted by trini_per4mance ↑I had an NST pulley, but I sold it.
Guys, the pinging that I'm hearing is very rear and I only hear it for like a second or two when the engine is under 99% load sometimes. I don't think it's my valves or timing chain, but then again, I may be wrong. I think is has to do with the fuel and the fact that my O2 sensors and knock sensor have 350K miles on them. So, they may not be functioning 100%.
So do you have a video made of the 350,000 rollover? Post it up!
🎉
🎉
ohh my god that is freaking awesome!!!!! you should contact toyota inmediatly and get sponsored, discounts and you could be on TV lol
awesome dude, freaking awesome..
awesome dude, freaking awesome..
Yes, I do have a video. But I need to get someone who can edit it and add captions and music to it. I would like to do a compilation of all the vids I have, from the 100k mile vid up to the most recent 350k vid. Anyone willing to help me out with doing this? I would greatly appreciate it. Thanx!Originally Posted by Kal-El ↑So do you have a video made of the 350,000 rollover? Post it up!
🎉
WISHFUL THINKING.😆 sponsorship from toyota😆Originally Posted by toyo ↑ohh my god that is freaking awesome!!!!! you should contact toyota inmediatly and get sponsored, discounts and you could be on TV lol
awesome dude, freaking awesome..
trini,
Any update on the "ping" issue after the MAF cleaning, injector cleaner, etc?
TIA
R2
Any update on the "ping" issue after the MAF cleaning, injector cleaner, etc?
TIA
R2
Yeah, it's almost gone. I very rarely hear it for a second once in a blue moon.Originally Posted by R2D2 ↑trini,
Any update on the "ping" issue after the MAF cleaning, injector cleaner, etc?
TIA
R2
Cool, thanks!
R2
R2
i thought you had a magnaflow exhaust?Originally Posted by trini_per4mance ↑I have a dynomax exhaust, but cruising at 70mph, you don't hear any intake or exhaust noise. The car is almost as quiet as factory while cruising.
Maybe if you have time you can create a "View User's Garage" so we can see what's your yaris mod's and some pictures.
Congrats! :D
I have either a dynomax or magnaflow oem replacement exhaust with 2.25" inlet and outlet with a stock looking elbow tip facing down. I wanted the performance but keep it looking stock as possible.Originally Posted by Split ↑i thought you had a magnaflow exhaust?
Trini How did u put 350K in this 07 sedan?