Yarisworld Archive

0/1 guage through firewall?

23 posts · 6,781 views

POORSHAOriginal postNE CT · Jul 19, 2009#1
For smaller wire I know about the grommet behind the battery. How about larger wire ?

Replies 22

BrianRiverside, CA · Jul 19, 2009#2
It'll still fit through the same grommet behind the battery. There's a lot of room there.
ChinoCharlesOH · Jul 19, 2009#3
With the Yaris, just drill another damn hole. LOL. I hate wiring Yarii.
POORSHAThread starterNE CT · Jul 19, 2009#4
I would drill, I just don't want to hit anything. I can't believe there isn't an unused plug on the fire wall.
BrianRiverside, CA · Jul 19, 2009#5
I got the plug that connects to my fog light switch through the grommet behind the battery
easily so a 0/1 gauge wire will be no problem. Why a 0/1 gauge wire though? How much power
are you planning on running through it? Just curious.
POORSHAThread starterNE CT · Jul 19, 2009#6
1500 watts
IllusionXBrossard, QC · Jul 20, 2009#7
the grommet does fit gauge 0 wire..
POORSHAThread starterNE CT · Jul 21, 2009#8
Thanks for the info
talnlnkySpokane, Wa · Jul 21, 2009#9
I don't think I saw this grommet you people talk of... do you have to yank the battery to see it, or gain access?

I've got some 2/0awg that i'd like to run, but I couldn't find a place that it'd fit... so i'm running some 4awg that I had laying around.
BrianRiverside, CA · Jul 21, 2009#10
I pulled the winshield wiper assembly off because I didn't want to remove my STB to
get the battery out and it was much easier to access that way.
IllusionXBrossard, QC · Jul 21, 2009#11
Originally Posted by Brian ↑
I pulled the winshield wiper assembly off because I didn't want to remove my STB to
get the battery out and it was much easier to access that way.
the correct way of doing it is removing the windshield wiper/wiper motor assembly.
ChinoCharlesOH · Jul 21, 2009#12
Well that certainly explains a lot of things. 😆 Thanks!
POORSHAThread starterNE CT · Aug 9, 2009#13
The trick to putting o/1 through the fire wall is to remove half the car first.
1) remove wipers
2) remove wiper trim
3) remove wiper motor assembly
4)remove radio trim
5) remove guage bezel
6) remove guage cluster
7) remove a pillars
8) remove dash
now you can start with the wire, solder a ring terminal on to the wire. Pull the wire from the interior to the engine bay.

done. 4+ hrs👍
SlickHouston, Texas · Aug 9, 2009#14
Just to add a bit of install info... There is another unused rubber grommet on the passanger side, about 4 inches below the roof of the engine bay and about 6-8 inches from the side. It comes below the dash, which can be easily accessed by pulling the carpet back a little ways and looking up. Will give pics if asked.
goku87AK · Aug 15, 2009#15
Originally Posted by Slick ↑
Just to add a bit of install info... There is another unused rubber grommet on the passanger side, about 4 inches below the roof of the engine bay and about 6-8 inches from the side. It comes below the dash, which can be easily accessed by pulling the carpet back a little ways and looking up. Will give pics if asked.
ryotaRochester NY · Aug 15, 2009#16
Originally Posted by Slick ↑
Just to add a bit of install info... There is another unused rubber grommet on the passanger side, about 4 inches below the roof of the engine bay and about 6-8 inches from the side. It comes below the dash, which can be easily accessed by pulling the carpet back a little ways and looking up. Will give pics if asked.

this is the one i used for my wire
AlexNet0Rockland, ME · Aug 15, 2009#17
^ i used this for my fogs as well, it should be a few inches farther than the engine ECU to the passenger side, looking from in front of the car, directly left of the ECU.
SlickHouston, Texas · Aug 16, 2009#18
Thats good, I watch this post for days and nothing, and then the day after I re-run the power wire I see that pics are wanted 😢 oh well, i'll post a few pics in a day or two, cause i'm a lazy pos 😈 And a 4 guage fits through the grommet as well, looks like enough room to squeez a 0 with a little fuss but not impossible.
HapaHawaii, USA · Nov 27, 2009#19
Originally Posted by Slick ↑
Just to add a bit of install info... There is another unused rubber grommet on the passanger side, about 4 inches below the roof of the engine bay and about 6-8 inches from the side. It comes below the dash, which can be easily accessed by pulling the carpet back a little ways and looking up. Will give pics if asked.
hurt my finger doing this T_T
HapaHawaii, USA · Nov 27, 2009#20
its more like 1 inch from the engine roof
skdragonTrujillo Alto Puerto Rico · Mar 5, 2010#21
i wanna see pics of the one behind the battery. its my first yaris ad i had it like for 3 weeks now. Please
CTScottUSA, CT · Mar 5, 2010#22
Originally Posted by skdragon ↑
i wanna see pics of the one behind the battery. its my first yaris ad i had it like for 3 weeks now. Please
Here's a pic of it looking up under the dash:

Picture not included in this copy
CTScottUSA, CT · Mar 5, 2010#23
And, here's a pic from the engine side. Not that the wiper cowling and the metal tray that the wiper motor mounts to are removed in this picture:

Picture not included in this copy

1 attachment not included in this copy