vodkalushOriginal postRochester, NY · Dec 4, 2006#1Description:
To change every none-white indicator light to either white or blue.
****The backlighting to the Speedometer and Tach use a piece of "smoked plastic/acryllic" to spread the light of serveral LEDs across the face of the speedo and various parts of the cluster, meaning any replacement color would be slightly "smoked" or slightly darker then the attended output color. My theory is that if you use a higher output LED then you could offset the "smoke".
Tools Needed:
- Philips head screw driver
- Hands
- Soldering Iron (with small tip)
- 30 New LEDS’s
*** I ordered these White LEDS -
http://www.eled.com/product.asp?cata...EPT2012RWF%2DA (replaced stock white with theses; not necessary)
*** I ordered these Blue LEDs -
http://www.eled.com/product.asp?cata...=EP2012PBC%2DA (replaced all non-white with these; well until i ran out :-) )
- Extra Solder
- Needle nose pliers
Instructions:
1. Remove outer “molding” around stereo and guage cluster
Picture lost · kgillette.googlepages.com 2. Remove both sets of wire’s going to gauge cluster, then unscrew two screws holding the gauge cluster
Picture lost · kgillette.googlepages.com 3. Bring the cluster indoors to a static free environment (or have a static wrist band).
Picture lost · kgillette.googlepages.com 4. Flip over the guage cluster, unscrew the 3 screws, then pop the black tabs, remove white backing
Picture lost · kgillette.googlepages.com 5. Remove “raised board,” lift+pull straight out
Picture lost · kgillette.googlepages.comPicture lost · kgillette.googlepages.com 6. Flip over gauge cluster, and then pull out the “gauge needles” (pull from base of the needle;the round part, they are on tight, but will come loose)
Picture lost · kgillette.googlepages.com 7. Admire the bare circuit board :drools:; take note of the LED positions
Picture lost · kgillette.googlepages.com 8. Use pliers and “grip” middle of OEM LED, use the soldering iron in other hand and heat up one point of the LED solder point and then lift with the pliers on that side of the LED, after one side is free heat-up the other side of the LED and lift the LED off the board.
There is an arrow at the bottom of the LED point the arrow in the same direction as the arrow on the circuit board and re=solder the LED (please Google “how to solder” if you are not familiar with soldering) (x30ish)
Picture lost · kgillette.googlepages.com 9. After repeating step 8 on all LED colors that you wish to change, then reverse the steps to put back together the Gauge Cluster (make sure you put the longer gauge needle on the speedometer)
Picture lost · kgillette.googlepages.com hope this helps
Replies 88
vodkalushThread starterRochester, NY · Dec 5, 2006#2👍
ViolinNew Jersey · Dec 5, 2006#3Sweet!
Did you have any trouble getting the needles put back on correctly?
ViolinNew Jersey · Dec 5, 2006#4What LEDs did you use? Where did you get them?
vodkalushThread starterRochester, NY · Dec 5, 2006#5edited first post to include LEDs; I'm also going to work on labling the circuit-board picture with a "layout map," that that prob wont happen until the end of the week.
vodkalushThread starterRochester, NY · Dec 5, 2006#6 Originally Posted by
Violin ↑ Sweet!
Did you have any trouble getting the needles put back on correctly?
nope, they slip right back on, when you plug the cluster back in (well atleast mine seemed to) the needles seem to "re-align" themselves
vodkalushThread starterRochester, NY · Dec 5, 2006#7if anyone does this and only has a speedometer (no tach) but notices that they have 2 of these (pic below) please PM me.
punchBarrie, ontario · Dec 5, 2006#8guess chino owes you some booze!
ViolinNew Jersey · Dec 5, 2006#9Thanks for this vodka - I hope the hatch is similar.
What soldering iron do you use for this work?
vodkalushThread starterRochester, NY · Dec 5, 2006#10some cheap-o radio shack one; however now thinking about it, I did use a small tipped soldering point.
1st post updated.
KatanaUnder the hood! · Dec 5, 2006#11Perfect!
Wish I could find a DIY for mine!
vodkalushThread starterRochester, NY · Dec 5, 2006#12the design shouldnt have changed that much from the 06-07.... and there really shouldnt be a real difference between the LB and Sedan (other then physical size), takeing apart the whole thing (include car removal) should take maybe 10-15mins. I say give it a shot.
KatanaUnder the hood! · Dec 5, 2006#13Thanks for anwsering!
Well, the thing is that mine is digital!
vodkalushThread starterRochester, NY · Dec 5, 2006#14 Originally Posted by
Katana ↑ Thanks for anwsering!
Well, the thing is that mine is digital!
well you know that means that you could change the "backlighting" of the digital read outs (a pic would help), I'm gonna take a guess and say that the construction of the housing is similar but the amount of soldering will go up drasticly (the sedans intergrated LCD uses 32 LEDs and its only somthing like 3x5inches (or somthing like that) )
paultyler_82USA · Dec 6, 2006#15There is a big difference between LB and Sedan, the Sedans use standard LED backlit gauges like the celica, the LB's use Optitron, which, as I understand, is high contrast white LED's behind layers of colored and smoked acryllic. As for the Digital readouts... you might try disassembling your cluster and attaching colored celophane paper to the segment LEDs underneath, this is what i30 and Maxima people do to change the digital displays on thier radios, A/C's, and clocks.
KatanaUnder the hood! · Dec 6, 2006#16I am planning on disassembling the panel, to figure out what's behind.
vodkalushThread starterRochester, NY · Dec 6, 2006#17 Originally Posted by
paultyler_82 ↑ There is a big difference between LB and Sedan, the Sedans use standard LED backlit gauges like the celica, the LB's use Optitron, which, as I understand, is high contrast white LED's behind layers of colored and smoked acryllic. As for the Digital readouts... you might try disassembling your cluster and attaching colored celophane paper to the segment LEDs underneath, this is what i30 and Maxima people do to change the digital displays on thier radios, A/C's, and clocks.
well as far as the speedo-tach-and "backlighting" then the sedan is the same way, I wasnt interested in chaning the backlighting (just the gauge cluseter indicators) but, you could change all the LEDs; which include the lighting to the smoked arcyllic (it seems to use what I'm gonna call "light tubes" to lite the acryllic) if you change the "backlight color" the outcome will be a slightly darker color then what you buy; so if you get a "high intensity" LED you might be able to make up from the "smoke"
edit:
but then again the only way to know for sure is to have someone with an LB take apart their gauge cluster to see just whats there (a posted pic for verification would be flipp'n sweet)
vodkalushThread starterRochester, NY · Dec 6, 2006#18I have updated some information in the first post.
ViolinNew Jersey · Dec 6, 2006#19When I took mine apart before, I didn't see any LEDs and was pretty confused. I'll have another go at it and post some photos.
H8SGASSan Diego, CA · Dec 7, 2006#20Yet again great work......You know it's a new car right? 😁 (<---for the rest of you this is a joke from the WNY Meets)
BeauFrederick, Maryland. USA · Dec 10, 2006#21
Picture lost · kgillette.googlepages.com
What about your parking indicator? Why is it still Green?
Is there a way to make that blue as well?
vodkalushThread starterRochester, NY · Dec 11, 2006#22haha, yeah, its still green because I mis-judged the amount of LEDs that I would need, I didnt have enough for either the gear indicators or the door indicator. I will be finishing the color change, but not till after christmas (everythings to hecktic :-) )
||)) (o) ||\||Southwest PA · Dec 23, 2006#23Ok after a few dumb mistakes and 3 packs of smokes later, heres my outcome of my gauge cluster led change! Keep in mind the stereo screen isnt that bright in person. Kudos to Mr.Vodka!
Picture lost · i143.photobucket.com ||)) (o) ||\||Southwest PA · Jan 13, 2007#24Heres a little more clear of a picture. Sorry just wanted to bump the thread
Picture lost · i143.photobucket.com
vodkalushThread starterRochester, NY · Jan 14, 2007#25Nice to see some other brave soles out there! I like the theme it ties in the whole center together 👍
vodkalushThread starterRochester, NY · Jan 23, 2007#26Update For LB Owners: This can be done on a LB
It wont be for a little while, but I will post a modified DIY, as the Cluster looks a little different when taking it apart.
Will keep you all updated.
Jem_hadarCollingwood, ON · Jan 26, 2007#27 Originally Posted by
vodkalush ↑ Update For LB Owners: This can be done on a LB
It wont be for a little while, but I will post a modified DIY, as the Cluster looks a little different when taking it apart.
Will keep you all updated.
NICE! Thank you, looking forward to reading your post. I have a Canadian Hatchback, and I want to change just the backlighting from the bright white light, to a nice blue, like that used in VWs!! 😎
FROM THIS:
Picture lost · www.canadiandriver.com
TO THIS: Picture lost · www.canadiandriver.com (EDIT: I wonder if it'd be a problem if i DID NOT wannt to change as well the white lighting of the right-hand box part that holds the fuel bars, ODO and time? I'd like that left white as it is, but just change the lighting for the tach and speedo to blue!)
heheh and *maybe* the other warnings to red instead of the orange colour ;)
vodkalushThread starterRochester, NY · Jan 26, 2007#28I dont think you'll have problem with doing the switch... yours may be a little diff when taking it apart (as there is a slight difference with the LB cluster versus the Sedan) but its all pretty straight forward.. just be sure to take your time 👍
vodkalushThread starterRochester, NY · Jan 26, 2007#29oh yah: dont make the mistake I did, be sure to take the cluster apart and count how many LEDs you will need and then add another 5 (in case of mistakes/loss) before you order the new LEDs or else you may end up with a 3/4 completed cluster like mine 🙁
theFEVAMiami, FL · Jan 27, 2007#30i have a red sedan and was debating on whether to change all of the interior lights to red, or red and blue... does anyone have feedback on how the red leds would look? also for the dome lights im worried the light will look a lil pink... suggestions please
R0ME0Seattle, WA · Mar 21, 2007#31Any update on this vodka for the liftback?
brickhardmeatInner City, Dallas · Mar 21, 2007#32I think he fell off the face of the earth.
vodkalushThread starterRochester, NY · Mar 22, 2007#33haha, lifes been busy as all....
The liftback cluster can be changed.... chino tore his apart and took some pics. In-fact the lb cluster will be easier to change (as there are less LEDs to change out)
ChinoCharlesOH · Mar 22, 2007#34 Originally Posted by
vodkalush ↑ haha, lifes been busy as all....
The liftback cluster can be changed.... chino tore his apart and took some pics. In-fact the lb cluster will be easier to change (as there are less LEDs to change out)
Yeah, then I spent the next month trying to get the speedo pin not to stick at 40 MPH. That cluster is a PITA.
brickhardmeatInner City, Dallas · Mar 22, 2007#35I got my blue LED's today for the cluster and the stereo. I ordered 100 so hopefully i will have enough. I am going to have to beg my Dad to help me out with this one. This is his kind of thing though so hopefully I can get him into it. I'll post some pics of the L/B whenever I finally get it completed. I am wondering if there is a way to removed the greenish layer in the cluster. Looks like it is all one piece. I really wouldn't mind it staying white but I hate the green lines.
brickhardmeatInner City, Dallas · Mar 22, 2007#36by the way these suckers are freakin' tiny as freak, what the freak
gonna need a microscope
ChinoCharlesOH · Mar 22, 2007#37 Originally Posted by
brickhardmeat ↑ I got my blue LED's today for the cluster and the stereo. I ordered 100 so hopefully i will have enough. I am going to have to beg my Dad to help me out with this one. This is his kind of thing though so hopefully I can get him into it. I'll post some pics of the L/B whenever I finally get it completed. I am wondering if there is a way to removed the greenish layer in the cluster. Looks like it is all one piece. I really wouldn't mind it staying white but I hate the green lines.
100 is going to be a ton of overkill. Lucky for you I need the same ones. I'll take a cluster's worth off your hands when you're done. PM sent.
yrsdrgnSF,CA · Mar 22, 2007#38Take some pics of the underside of the LB cluster!!!!! Must look at by pictures before attempting install myself!!!! Thanks 👍
Jem_hadarCollingwood, ON · Mar 22, 2007#39 Originally Posted by
yrsdrgn ↑ Take some pics of the underside of the LB cluster!!!!! Must look at by pictures before attempting install myself!!!! Thanks 👍
indeed! +1
vodkalushThread starterRochester, NY · Mar 23, 2007#40haha, overkill is def better the underkill (as it is in my case) --- because nothing is worse then a half finished stereo+gauge cluster........
yrsdrgnSF,CA · Mar 23, 2007#41yea but you did the DIY thingy first so that's redemption hehe
uncleyarisToronto · Mar 24, 2007#42good to see VODKA back!!!!!!!!!!! 👍
ChinoCharlesOH · Mar 25, 2007#43Guys... I did take pictures of the inside of the LB cluster. Search.
yrsdrgnSF,CA · Mar 25, 2007#44 Originally Posted by
ChinoCharles ↑ Guys... I did take pictures of the inside of the LB cluster. Search.
I've been searching. Haven't seen any pics of the inside of the cluster and solder points. Maybe I'm just not putting the right words in the search thingy.
Black YarisToledo, OH · Mar 25, 2007#45I tried searching for Chino we tod did.... nothing WTF?
ChinoCharlesOH · Mar 25, 2007#46Gimme a second.
EDIT: Can't find it right now. This is going to take a while. Be patient.
yrsdrgnSF,CA · Mar 31, 2007#47 Originally Posted by
ChinoCharles ↑ Gimme a second.
EDIT: Can't find it right now. This is going to take a while. Be patient.
*second passes by* 🙄 🙄 😁
ChinoCharlesOH · Mar 31, 2007#48Oh jeez, I forgot all about this... and I'm on my way out the door again! Vodkalush... help! Where are those pictures???
BUELLER???
I'M DESPERATE HERE!
elsteverino889MIA! · Apr 1, 2007#49Ive scene this thread like a thousand times and I want somebody to do this for me bcuz i surely cant...any takers give u $50 some vodka...but u have to come down to Miami, FL
vodkalushThread starterRochester, NY · Apr 2, 2007#50chino, I cant find the damn pics either... for some reason I thought they where posted in a "branched" thread... I'll keep looking though...