Yarisworld Archive

DIY: Removing rear "toyota" and "yaris" emblems in 5 mins without heat! vid inside!

16 posts · 15,139 views

spkrmanOriginal post2 · Nov 19, 2006#1
No heat needed... the only "tools" you need are your fingers and some floss or fishing line. I used cheap floss with good results, it broke a few times but it got the job done. Use the floss to saw at the adhesive behind the emblems, keep your hands close to the car to make things easier.

When thats done, just knock off the foam adhesive with your finger - easier if you spray with water.

Follow the vid below its pretty self explanatory.

Easy, quick, and nice clean look afterwords :)

Replies 15

hasher22Australia Sydney · Nov 20, 2006#2
YAY! YOU GOT IT OFF!!!

nice vid tutorial too..... Mr. Nakey Yaris
spkrmanThread starter2 · Nov 20, 2006#3
Originally Posted by hasher22
YAY! YOU GOT IT OFF!!!

nice vid tutorial too..... Mr. Nakey Yaris
yep, by the time I'm done there will be nothing but a motor and a seat 🤘
eTiMaGoBangkok, Thailand · Nov 20, 2006#4
Cool! I think I will attempt this tonight... There are two extra very annoying badges put on by the dealer, but they are on very thin adhesive, I hope I can pull them off ok...
spkrmanThread starter2 · Nov 20, 2006#5
the process should work with anything attached with foam adhesive, if its extra thin, use extra thin fishing wire :)
ChinoCharlesOH · Nov 20, 2006#6
Not to take the wind out of your sails because you did a nice job, but this tutorial has been done. For everyone looking to post a new tutorial, you should always search the forums and see if you're posting something someone has already explained.

At least the newbies know now, though. 😁
ChinoCharlesOH · Nov 20, 2006#7
Well, I could make it... hehe.

Oh no, now everyone is afraid to swear. LOL who did that post, echo_hrs?
ChinoCharlesOH · Nov 20, 2006#8
HAHA! You're in rare form tonight aren't you.
spkrmanThread starter2 · Nov 20, 2006#9
Originally Posted by ChinoCharles
Not to take the wind out of your sails because you did a nice job, but this tutorial has been done. For everyone looking to post a new tutorial, you should always search the forums and see if you're posting something someone has already explained.

At least the newbies know now, though. 😁
Saw it after I posted this, at least I added a vid to the mix!
ChinoCharlesOH · Nov 21, 2006#10
I'll give you that, haha. Nice touch. What did you use?
spkrmanThread starter2 · Nov 21, 2006#11
Originally Posted by ChinoCharles
I'll give you that, haha. Nice touch. What did you use?
use for what?

for the vid? Windows movie maker :)
ChinoCharlesOH · Nov 21, 2006#12
To record itttt... digital camera with video feature, full out digital camcorder, or did you record this from a VHS tape. HAHA
spkrmanThread starter2 · Nov 21, 2006#13
Originally Posted by ChinoCharles
To record itttt... digital camera with video feature, full out digital camcorder, or did you record this from a VHS tape. HAHA
beta MAX!

digital picture cam with vid feature :)
UncleMoSeattle · Sep 15, 2009#14
Originally Posted by spkrman ↑
No heat needed... the only "tools" you need are your fingers and some floss or fishing line. I used cheap floss with good results, it broke a few times but it got the job done. Use the floss to saw at the adhesive behind the emblems, keep your hands close to the car to make things easier.

When thats done, just knock off the foam adhesive with your finger - easier if you spray with water.

Follow the vid below its pretty self explanatory.

Easy, quick, and nice clean look afterwords :)

I appreciate this as I perform the same task in a much slower manner.
custom LftbackHouston, TX · Sep 15, 2009#15
wow, ancient BUMP! haha
hexengonbby · May 6, 2010#16
do u have video to remove the front emblem